Abstract:High undercooling rapid solidification process has a significant impact on the solidified microstructure and mechanical properties of materials. In this study, particles with a diameter range between 100 and 1100 μm of ternary Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys were prepared by a drop tube. The evolution process of particle-solidified microstructure with decreasing particle diameter was analyzed using XRD, SEM, and TEM. For Zr 50 Cu 40 Al 10 alloy, the solidified microstructure in the particle diameter ranges of 200–1100 μm is composed of an amorphous phase and a primary B2-ZrCu high-temperature metastable phase. As the particle diameter reduces, the retained crystalline phase in the solidified microstructure decreases progressively, and the dendrite grain length gradually becomes finer. When the particle diameter is reduced to below 200 μm, the crystalline phase has completely disappeared, and the solidified microstructure evolves into a completely amorphous structure. For Zr 49 Cu 46 Al 5 alloy, in the particle diameter range of 400–1100 μm, the solidified microstructure consists of primary B19'-ZrCu phase, a small amount of Cu 10 Zr 7 phase and Zr 14 Cu 51 phase. As the particle diameter reduces, a grain refinement phenomenon also occurs in the solidified microstructure and the dendritic morphology changes from equiaxed grain to rod-shaped dendrite. The amorphous phase appears when the particle diameter is lowered to 470 μm and solidified microstructure evolves into a completely amorphous structure as the particle diameter is reduced to 146 μm. The nanoindentation results show that the micromechanical properties of amorphous composite microstructures are superior to the single component composition of crystalline or amorphous phase for Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys. The reinforcement effect on the amorphous phase is related to the content of the second crystalline phase. Moreover, under similar particle diameters, the mechanical properties of Zr 50 Cu 40 Al 10 particles are always better than those of Zr 49 Cu 46 Al 5 particles.

Liquid phase separation of Cu–Cr alloys during the vacuum breakdown

Influence of Microstructure on Dielectric Strength of Cucr Contact Materials in A Vacuum

Arc Characteristics and Microstructure Evolution of W–Cu Contacts During the Vacuum Breakdown

Effect of Ni Addition on the Dielectric Strength and Liquid Phase Separation of Cu–Cr Alloys During the Vacuum Breakdown

The Solidification of Cucr Alloys under Various Cooling Rates

Phase Transformation in Melt Layer of CuCr Contact Materials after Breaking Operations

Rapid Solidification Structure Refinement Mechanism in Highly Undercooled Cu Based Ternary Alloys

Formation of Cu-rich crystalline/NiNb-rich amorphous composite induced by liquid phase separation

Rapid Solidification of Cu60Co30Cr10 Alloy under Different Conditions

Liquid Phase Separation and Solidification of Cu40Co3oCr30 Alloy under Different Cooling Conditions

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Liquid separation behavior of Cu-Co alloy during isothermal process at high temperature

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

Growth Velocity-Undercooling Relationship and Structure Refinement Mechanism of Undercooled Ni-Cu Alloys

Solidification Microstructure in a Supercooled Binary Alloy

Dynamics and microstructural evolution of bulk amorphous Cu 12.5 Ni 10 Zr 41 Ti 14 Be 22.5 during phase separations: a small-angle neutron scattering approach

Effects of Zr addition on the liquid phase separation and the microstructures of Cu-Cr ribbons with 18-22 at.% Cr

Supercooling, Isothermal Soaking and Liquid Phase Separation of Cu–Co Alloys

Liquid and Solid Phase Separation During Melt Spinning and Annealing in Melt-Spun Cu–Cr Ribbons

Crystalline and amorphous microstructure evolution of Zr-Cu-Al ternary alloys solidified in drop tube

Phase and microstructure evolution in Cu-In-Cr alloys