Energy Calculation of the Stacking Fault in Fcc Metals by Embedded-Atom Method

JM Zhang,XJ Wu,YH Huang,KW Xu

DOI: https://doi.org/10.7498/aps.55.393

2006-01-01

Abstract:The stacking fault energies of fcc metals have been calculated by the embedded-atom method for 10 fcc metals, Cu, Ag, Au, Ni, Al, Rh, Ir, Pd, Pt and Pb. The calculated values are in good agreement with experimental results, that of Rh and Ir excepted.

What problem does this paper attempt to address?

Calculations of Stacking-Fault Energy for Fcc Metals and Their Alloys Based on an Improved Embedded-Atom Method

XL NIE,RH WANG,YY YE,YM ZHOU,DS WANG

DOI: https://doi.org/10.1016/0038-1098(95)00506-4

IF: 1.934

1995-01-01

Solid State Communications

Abstract:An accurate and simple model for calculating stacking fault energies has been developed based on our improved embedded-atom method. Using this model we have calculated stacking fault energies for some pure fcc metals and some fcc disordered solid solutions for NiCu, NiCo, NiAl alloys. The calculated results are in good agreement with the experimental ones.
Self-energy and Interaction Energy of Stacking Fault in Fcc Metals Calculated by Embedded-Atom Method

He Gang,Rong Yonghua,Xu Zuyao

DOI: https://doi.org/10.1007/bf02916884

2000-01-01

Science China Technological Sciences

Abstract:The stacking fault energies of five fcc metals (Cu, Ag, Au, Ni and Al) with various quantivalences have been calculated by embedded-atom method (EAM). It indicated that the stacking fault energy is mainly determined by the metallic bond-energy and the lattice constant. Thus, monovalent fcc metals should have different stacking fault energies, contracy to Attree’s conclusion. The interaction energy between stacking faults one {111} layer apart in a fcc metal is found to be 1/40–1/250 of its self-energy, while it becomes zero when the two stacking faults are two layers apart. The twin energy is just half of the energy of intrinsic stacking fault energy without the consideration of lattice relaxation and the energy of a single intrinsic stacking fault is almost the same as that of extrinsic stacking fault, which are consistent with the results from the calculation of Lennard-Jones force between atoms, but differ from Attree’s result.
Generalized Stacking Fault Energy in Fcc Metals with Meam

Xiu-Mei Wei,Jian-Min Zhang,Kewei Xu

DOI: https://doi.org/10.1016/j.apsusc.2007.07.078

IF: 6.7

2007-01-01

Applied Surface Science

Abstract:The second nearest-neighbor modified embedded atom method (2NN-MEAM) is used to investigate the generalized stacking fault (GSF) energy surfaces of eight FCC metals Cu, Ag, Au, Ni, Pd, Pt, Al and Pb. An offset is observed in all the metals for the displacement δus of unstable stacking fault energy from the geometrically symmetric displacement point δus0. The offset value is the greatest for Al and the smallest for Ag. By analyzing the stable stacking fault energy γsf and unstable stacking fault energy γusf, it can be predicted that stacking fault is more favorable in Cu, Ag, Au, and especially in Pd than the other metals, while it is most preferred to create partial dislocation for Ag and to create full dislocation for Al.
Generalized Stacking Fault Energies for Embedded Atom FCC Metals

JA Zimmerman,HJ Gao,FF Abraham

DOI: https://doi.org/10.1088/0965-0393/8/2/302

IF: 2.421

2000-01-01

Modelling and Simulation in Materials Science and Engineering

Abstract:Atomistic calculations for the [112]-generalized stacking fault (GSF) energy curve are performed for various embedded atom models of FCC metals. Models include those by Voter and Chen: Angelo, Moody and Baskes; Oh and Johnson; Mishin and Farkas; and Ercolessi and Adams. The resulting curves show similar characteristics but vary in their agreement with the experimental estimates of the intrinsic stacking fault energy, gamma(sf), and with density functional theory (DFT) calculations of the GSF curve. These curves are used to obtain estimates of the unstable stacking fault energy, gamma(us), a quantity used in a criterion for dislocation nucleation. Curves For nickel and copper models show the theoretically expected skewed sinusoidal shape; however, several of the aluminium models produce an irregularly shaped GSF curve. Copper and aluminium values for gamma(us) are underestimates of calculations from DFT, although some of the nickel models produce a value matching one of the available DFT results. Values for gamma(sf) are either fitted to, or underestimate, the measured results. For use in simulations, the authors recommend using the Voter and Chen potential for copper, and either the Angelo, Moody and Baskes potential or the Voter and Chen potential for nickel. None of the potentials model aluminium well, indicating the need for a more-advanced empirical potential.
Stacking fault energy of face-centered cubic metals: thermodynamic and ab initio approaches

Ruihuan Li,Song Lu,Dongyoo Kim,Stephan Schönecker,Jijun Zhao,Se Kyun Kwon,Levente Vitos

DOI: https://doi.org/10.1088/0953-8984/28/39/395001

2015-11-27

Abstract:The formation energy of the interface between face-centered cubic (fcc) and hexagonal close packed (hcp) structures is a key parameter in determining the stacking fault energy (SFE) of fcc metals and alloys using thermodynamic calculations. Often the contribution of the planar fault energy to the SFE has the same order of magnitude as the bulk part, and thus the lack of a precise information about it can become the limiting factor in thermodynamic predictions. Here, we differentiate between the actual interfacial energy for the coherent fcc(111)/hcp(0001) interface and the "pseudo-interfacial energy" that enters the thermodynamic expression for the SFE. Using first-principles calculations, we determine the coherent and pseudo- interfacial energies for six elemental metals (Al, Ni, Cu, Ag, Pt, and Au) and for three paramagnetic Fe-Cr-Ni alloys. Our results show that the two interfacial energies significantly differ from each other. We observe a strong chemistry dependence of both interfacial energies. The calculated pseudo-interfacial energies for the Fe-Cr-Ni steels agree well with the available literature data.

Materials Science
A determination of the stacking-fault energy of some pure F.C.C. metals

I. L. Dillamore,R. E. Smallman,W. T. Roberts

DOI: https://doi.org/10.1080/14786436408222963

1964-03-01

Abstract:A method for determining the stacking-fault energy of f.c.c. materials has been developed using an already-established dependence of preferred orientation on stacking-fault energy. An empirically determined parameter, characteristic of the type of rolling texture exhibited by the metal, is related to the stacking-fault energy value obtained by measurements of dislocation node radius, and from the γ value for the three metals, Ag, Cu and ni the stacking-fault energy of Th, Au, Pd, Rh, Pt and Yb has been obtained by interpolation using measured values of the texture parameter.

materials science, multidisciplinary,physics, applied, condensed matter,metallurgy & metallurgical engineering
Structure and Stacking-Fault Energy in Metals Al, Pd, Pt, Ir, and Rh

J Cai,F Wang,C Lu,YY Wang

DOI: https://doi.org/10.1103/physrevb.69.224104

IF: 3.7

2004-01-01

Physical Review B

Abstract:The generalized stacking faults of Al, Pd, Pt, Ir, and Rh are investigated by a parametrized tight-binding potential. The stacking-fault energies (SFEs) are calculated to be in good agreement with experimental data, except for Al. More important, it is found that the SFE of Pt may be reduced by 14% by atom relaxation while the effect of atom relaxation on the SFEs of Al, Pd, Ir, and Rh are small. Thus, it is concluded that the effect of atom relaxation on SFE should be important, especially for an alloy system where radii difference between two constituting elements is large.
Stacking-fault energies for Ag, Cu, and Ni from empirical tight-binding potentials

R. Meyer,L. J. Lewis

DOI: https://doi.org/10.1103/PhysRevB.66.052106

2002-07-12

Abstract:The intrinsic stacking-fault energies and free energies for Ag, Cu, and Ni are derived from molecular-dynamics simulations using the empirical tight-binding potentials of Cleri and Rosato [Phys. Rev. B 48, 22 (1993)]. While the results show significant deviations from experimental data, the general trend between the elements remains correct. This allows to use the potentials for qualitative comparisons between metals with high and low stacking-fault energies. Moreover, the effect of stacking faults on the local vibrational properties near the fault is examined. It turns out that the stacking fault has the strongest effect on modes in the center of the transverse peak and its effect is localized in a region of approximately eight monolayers around the defect.

Materials Science
Calculation of the Stacking Fault Energies of Fe-Mn Alloys by Embedded-Atom Method

戎咏华,孟庆平,何刚,徐祖耀

DOI: https://doi.org/10.16183/j.cnki.jsjtu.2003.02.007

2003-01-01

Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University

Abstract:Embedded-atom method (EAM) was introduced to calculate the stacking fault energies (SFE) of Fe-Mn alloys. The calculated results based on Johnson's truncation model and its modified model indicate that the SFE in Fe-20Mn alloy increases with the increase of Mn content and the tendency is well consistent with our experiments. Moreover, the SFE in Fe-20Mn is well agreement with that thermodynamically calculated by Kato et al. The SFE or γ phase in Fe-Mn alloys with α(Mn)=20%-55% can be expressed as; SFE (mJ/m 2)=23.3+0.269 α(Mn)%.
Density functional theory calculations of generalized stacking fault energy surfaces for eight face-centered cubic transition metals

Yanqing Su,Shuozhi Xu,Irene J. Beyerlein

DOI: https://doi.org/10.1063/1.5115282

IF: 2.877

2019-09-12

Journal of Applied Physics

Abstract:In this work, we use density functional theory to calculate the entire generalized stacking fault energy (GSFE) surface for eight transition metals with a face-centered cubic structure: Ag, Au, Cu, Ir, Ni, Pd, Pt, and Rh. Analysis of the <math> ⟨ 112 ⟩</math> GSFE curves finds that the displacements corresponding to the unstable stacking fault energy are larger than the ideal value for all eight metals except Ag and Cu. Over the entire surface, Pt is found to not possess well-defined local maxima or minima, suggesting spreading in favor of dissociation of the dislocation core, unlike the other seven metals. Our calculations also reveal that at a large <math> ⟨ 112 ⟩</math> displacement, where atoms on two {111} adjacent planes are aligned, an anomalous local minimum occurs for Ir and Rh. The oddity is explained by relatively large, localized atomic displacements that take place in the two metals to accommodate the alignment that do not occur in the other six metals. In addition to the fully calculated surfaces, we characterize a continuous 11-term Fourier-series function, which provides a particularly excellent representation of the GSFE surfaces for Ag, Au, Cu, Ni, and Pd.

physics, applied
Effective Stacking Fault Energy in Face-Centered Cubic Metals

Ke-Qiang Li,Zhen-Jun Zhang,Lin-Lin Li,Peng Zhang,Jin-Bo Yang,Zhe-Feng Zhang

DOI: https://doi.org/10.1007/s40195-018-0718-4

2018-01-01

Acta Metallurgica Sinica (English Letters)

Abstract:As a typical configuration in plastic deformations, dislocation arrays possess a large variation of the separation of the partial dislocation pairs in face-centered cubic（fcc） metals. This can be manifested conveniently by an effective stacking fault energy（SFE）. The effective SFE of dislocation arrays is described within the elastic theory of dislocations and verified by atomistic simulations. The atomistic modeling results reveal that the general formulae of the effective SFE can give a reasonably satisfactory prediction for all dislocation types, especially for edge dislocation arrays. Furthermore, the predicted variation of the effective SFE is consistent with several previous experiments, in which the measured SFE is not definite, changing with dislocation density. Our approach could provide better understandings of cross-slip and the competition between slip and twinning during plastic deformations in fcc metals.
Twin-boundary and Stacking-Fault Energies in Al and Pd.

JH XU,W LIN,AJ FREEMAN

DOI: https://doi.org/10.1103/physrevb.43.2018

1991-01-01

Abstract:The (111) twin-boundary and stacking-fault energies of aluminum and palladium were investigated with use of the all-electron total-energy linear muffin-tin orbitals method based on the local-density approximation. Fault energies are determined by comparing the total energies obtained for the same-size supercells for each of two cases (with and without fault). The calculated values of the twin, intrinsic, and extrinsic fault energies, 130 +/- 15 (97 +/- 5), 270 +/- 50, and approximately 330 ergs/cm2 for aluminum (palladium) are generally 30% larger than experiment. This discrepancy between the calculated and observed values may be attributed to the neglect of relaxation, the effect of the (finite) size of the supercell (at most 28 atoms/cell), and/or the use of the local-density approximation. Our calculated results appear to verify the correctness of the empirical relationship 2E(tw) congruent-to E(SF), where E(tw) and E(SF) are the twin and stacking-fault energies, respectively.
Stacking Fault Energies in Austenitic Stainless Steels

Jun Lu,Lars Hultman,Erik Holmstrom,Karin H. Antonsson,Mikael Grehk,Wei Li,Levente Vitos,Ardeshir Golpayegani

DOI: https://doi.org/10.1016/j.actamat.2016.03.042

IF: 9.4

2016-01-01

Acta Materialia

Abstract:We measure the stacking fault energy of a set of 20 at% Cr-austenitic stainless steels by means of transmission electron microscopy using the weak beam dark field imaging technique and the isolated dislocations method. The measurements are analyzed together with first principles calculations. The results show that experiment and theory agree very well for the investigated concentration range of Mn (0-8%) and Ni (11-30%). The calculations show that simultaneous relaxation of atomic and spin degrees of freedom is important in order to find the, global energy minimum for these materials. Our results clearly show the great potential of the weak beam dark field technique to obtain accurate measurements of the stacking fault energy of austenitic steels and that the reliable predictability of first principles calculations can be used to design new steels with optimized mechanical properties. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Calculation of the Surface Energy of Fcc Metals with Modified Embedded-Atom Method

JM Zhang,F Ma,KW Xu

DOI: https://doi.org/10.1016/j.apsusc.2005.10.043

IF: 6.7

2004-01-01

Applied Surface Science

Abstract:The surface energies for 38 surfaces of fcc metals Cu, Ag, Au, Ni, Pd, Pt, Al, Pb, Rh and Ir have been calculated by using the modified embedded-atom method. The results show that, for Cu, Ag, Ni, Al, Pb and Ir, the average values of the surface energies are very close to the polycrystalline experimental data. For all fcc metals, as predicted, the close-packed (111) surface has the lowest surface energy. The surface energies for the other surfaces increase linearly with increasing angle between the surfaces (hkl) and (111). This can be used to estimate the relative values of the surface energy.
Alloy Model for the Stacking Fault Energy

XL Nie,YM Zhou,LP Zhong,DS Wang,RH Wang,YY Ye

1996-01-01

Abstract:An accurate and simple model of stacking fault energy for alloys (solid solutions) has been developed based on the embedded-atom method. The calculated value of stacking fault energy, 35 mJ/m(2) for 304 austenitic stainless steel, is in a good agreement with the experimental one, 30 mJ/m(2). In the present model we find that the Hirth's empirical relationship is also suitable for alloy.
Thermodynamic Calculation of Stacking Fault Energy in Fe–Mn–Si Shape Memory Alloys

XJ Jin,JH Zhang,TY Hsu

DOI: https://doi.org/10.1016/s0261-3069(00)00006-6

2000-01-01

Abstract:Based on thermodynamic considerations together with measurement of the stacking fault probability (Psf) by X-ray diffraction profile analysis, the stacking fault energy (SFE, γ) of austenite in Fe–Mn–Si shaped memory alloys can be estimated. For instance, the stacking fault energy of an fcc(γ) phase in an Fe–30.3Mn–6.06Si was calculated as 7.8 mJ/m2. Compositional dependence of stacking fault energy in these alloys with certain composition range has also been derived as SFE(γ)=180.54+7.923 wt.% Mn–46.38 wt.% Si (J/mol), showing that the stacking fault energy increases with the addition of Mn and decreases with the addition of Si.
Computational Thermodynamic and First-Principles Calculation of Stacking Fault Energy on Ternary Co-based Alloys

Tria Laksana Achmad,Wenxiang Fu,Hao Chen,Chi Zhang,Zhi-Gang Yang

DOI: https://doi.org/10.1016/j.commatsci.2017.11.004

IF: 3.572

2017-01-01

Computational Materials Science

Abstract:Theoretical calculation of stacking fault energy (SFE) needs to be investigated closely in each alloy system due to the complex effect between different elements. In this study, we have revealed that the computational thermodynamic approach and first-principles density-functional-theory (DFT) calculations are capable of calculating the SFE for developing and designing ternary Co-based alloys with low SFE and excellent mechanical properties. Interaction between Ni and Cr atoms in ternary systems can make a distinct effect to the SFE while interaction between Cr and Mo atoms gives more charge transfer then lower the SFE. Effect of alloying atom position and Cr concentrations of Co-Cr-W alloys was studied and explained regarding the electronic structure. In high Cr concentrations, Cr atoms that dispersing uniform are more useful to improving the strengthening effect than those dispersing segregatively.
Effects of Stacking Fault Energy on the Deformation Mechanisms and Mechanical Properties of Face-Centered Cubic Metals

Zhang Zhefeng,Li Keqiang,Cai Tuo,Li Peng,Zhang Zhenjun,Liu Rui,Yang Jinbo,Zhang Peng

DOI: https://doi.org/10.11900/0412.1961.2022.00548

IF: 1.797

2023-01-01

ACTA METALLURGICA SINICA

Abstract:Stacking fault energy (SFE) can play a crucial role in plastic deformation and damage mechanisms of face-centered cubic (fcc) metals. This study mainly summarized the following results: (1) With the reduction of SFE, the slip mode of fcc metals gradually changes from a facile cross-slip wavy mode to a planar mode until deformation twinning occurs; (2) The concept of effective SFE is applied to investigate the variation of SFE with dislocation density in the fcc metals, with the increase in dislocation density, the effective SFE increases; (3) The reduction of SFE is not the only factor determining the formation of deformation twins in fcc metals. In terms of calculating the competition between simulated slipping and twinning using the first principles, the critical criterion for forming deformation twinning in fcc metals was established; (4) The fatigue dislocation configuration of high-, medium-, and low-SFE fcc metals were analyzed and the judgment conditions for forming regular persistent slip bands (PSBs) are proposed; (5) With the increase in Al content, the SFE of Cu-Al alloy decreases, resulting in a simultaneous increasing trend in the tensile strength and the uniform elongation due to the increasing planar slip degree; (6) The exponential strain-hardening model can accurately describe the tensile strain-hardening process of Cu-Al alloys. The quantitative relationship among yield strength, tensile strength, and uniform elongation of Cu-Al alloy with different alloy compositions and microstructure states was successfully predicted; (7) With the increase in Al content, the fatigue strength of Cu-Al alloy is improved. Increasing Al content at the same strain amplitude will enhance its low-cycle fatigue life. Based on the experimental results above, it is shown that the alloy composition affects the deformation and damage mechanisms, and the evolution process of microscopic defects (dislocations, twins) in fcc metals and alloys. Thus, it drastically affects the tensile and fatigue properties of the fcc metals and alloys. These results provide experimental evidence and a theoretical basis for improving the mechanical properties and service reliability of fcc metals and alloys via alloy designing.
Can experiment determine the stacking fault energy of metastable alloys?

Xun Sun,Song Lu,Ruiwen Xie,Xianghai An,Wei Li,Tianlong Zhang,Chuanxin Liang,Xiangdong Ding,Yunzhi Wang,Hualei Zhang,Levente Vitos

DOI: https://doi.org/10.1016/j.matdes.2020.109396

2021-02-01

Abstract:Stacking fault energy (SFE) plays an important role in deformation mechanisms and mechanical properties of face-centered cubic (fcc) metals and alloys. In many concentrated fcc alloys, the SFEs determined from density functional theory (DFT) calculations and experimental methods are found having opposite signs. Here, we show that the negative SFE by DFT reflects the thermodynamic instability of the fcc phase relative to the hexagonal close-packed one; while the experimentally determined SFEs are restricted to be positive by the models behind the indirect measurements. We argue that the common models underlying the experimental measurements of SFE fail in metastable alloys. In various concentrated solid solutions, we demonstrate that the SFEs obtained by DFT calculations correlate well with the primary deformation mechanisms observed experimentally, showing a better resolution than the experimentally measured SFEs. Furthermore, we believe that the negative SFE is important for understanding the abnormal behaviors of partial dislocations in metastable alloys under deformation. The present work advances the fundamental understanding of SFE and its relation to plastic deformations, and sheds light on future alloy design by physical metallurgy.

materials science, multidisciplinary
Effect of vacancy defects on generalized stacking fault energy of fcc metals

Ebrahim Asadi,Mohsen Asle Zaeem,Amitava Moitra,Mark A Tschopp

DOI: https://doi.org/10.1088/0953-8984/26/11/115404

2014-03-19

Abstract:Molecular dynamics (MD) and density functional theory (DFT) studies were performed to investigate the influence of vacancy defects on generalized stacking fault (GSF) energy of fcc metals. MEAM and EAM potentials were used for MD simulations, and DFT calculations were performed to test the accuracy of different common parameter sets for MEAM and EAM potentials in predicting GSF with different fractions of vacancy defects. Vacancy defects were placed at the stacking fault plane or at nearby atomic layers. The effect of vacancy defects at the stacking fault plane and the plane directly underneath of it was dominant compared to the effect of vacancies at other adjacent planes. The effects of vacancy fraction, the distance between vacancies, and lateral relaxation of atoms on the GSF curves with vacancy defects were investigated. A very similar variation of normalized SFEs with respect to vacancy fractions were observed for Ni and Cu. MEAM potentials qualitatively captured the effect of vacancies on GSF.

Energy Calculation of the Stacking Fault in Fcc Metals by Embedded-Atom Method

Calculations of Stacking-Fault Energy for Fcc Metals and Their Alloys Based on an Improved Embedded-Atom Method

Self-energy and Interaction Energy of Stacking Fault in Fcc Metals Calculated by Embedded-Atom Method

Generalized Stacking Fault Energy in Fcc Metals with Meam

Generalized Stacking Fault Energies for Embedded Atom FCC Metals

Stacking fault energy of face-centered cubic metals: thermodynamic and ab initio approaches

A determination of the stacking-fault energy of some pure F.C.C. metals

Structure and Stacking-Fault Energy in Metals Al, Pd, Pt, Ir, and Rh

Stacking-fault energies for Ag, Cu, and Ni from empirical tight-binding potentials

Calculation of the Stacking Fault Energies of Fe-Mn Alloys by Embedded-Atom Method

Density functional theory calculations of generalized stacking fault energy surfaces for eight face-centered cubic transition metals

Effective Stacking Fault Energy in Face-Centered Cubic Metals

Twin-boundary and Stacking-Fault Energies in Al and Pd.

Stacking Fault Energies in Austenitic Stainless Steels

Calculation of the Surface Energy of Fcc Metals with Modified Embedded-Atom Method

Alloy Model for the Stacking Fault Energy

Thermodynamic Calculation of Stacking Fault Energy in Fe–Mn–Si Shape Memory Alloys

Computational Thermodynamic and First-Principles Calculation of Stacking Fault Energy on Ternary Co-based Alloys

Effects of Stacking Fault Energy on the Deformation Mechanisms and Mechanical Properties of Face-Centered Cubic Metals

Can experiment determine the stacking fault energy of metastable alloys?

Effect of vacancy defects on generalized stacking fault energy of fcc metals