Optimization of Catalytic Hydrogenation L-Alanine to L-Alaninol

XU Wei-xiang,MA Lei

DOI: https://doi.org/10.3969/j.issn.1006-4184.2012.08.008

2012-01-01

Abstract:Ru/C was used to be the catalyst for hydrogenation of L-Alanine to L-Alaninol.The effects of reaction temperature,H2 pressure and pH of the solution were considered.Otherwise,pretreatment activated carbon improved yield of target product.

What problem does this paper attempt to address?

Liquid-phase Hydrogenation of 2,2,4,4-Tetramethyl-1,3-cyclobutanedione over Supported Ru Based Catalysts

Yuxi Si,Lei Yang,Chengxiang Wang,Youwei Cheng,Siyu Yao,Lijun Wang,Xi Li

DOI: https://doi.org/10.1016/j.catcom.2022.106453

IF: 3.51

2022-01-01

Catalysis Communications

Abstract:A series of supported Ru based catalysts (support = AC, Al2O3, SiO2, HZSM-5) were prepared with different methods and applied in the hydrogenation of 2,2,4,4-tetramethyl-1,3-cyclobutanedione (CBDK) to 2,2,4,4-tetramethyl-1,3-cyclobutanediol (CBDO). Detailed catalyst characterizations of XRD, TEM, BET, ICP, XPS and NH3-TPD methods were applied to investigate the support effect and influence of preparation methods. Complete conversion of the substrate was achieved with the selectivity of CBDO up to 99.1% over Ru/AC catalysts. The superiority of Ru/AC catalyst prepared with chemical precipitation method over other counterparts were attributed to the larger specific surface area, smaller metal particle size and better Ru dispersion, which was more favorable for the hydrogenation of CBDK.
An Efficient and Reusable Embedded Ru Catalyst for the Hydrogenolysis of Levulinic Acid to Γ‐valerolactone

Zuojun Wei,Jiongtao Lou,Chuanmin Su,Dechao Guo,Yingxin Liu,Shuguang Deng

DOI: https://doi.org/10.1002/cssc.201601769

IF: 8.4

2017-01-01

ChemSusChem

Abstract:To achieve a higher activity and reusability of a Ru-based catalyst, Ru nanoparticles were embedded in N-doped mesoporous carbon through a hard-template method. The catalyst showed excellent catalytic performance (314h(-1) turnover frequency) and recyclability (reusable five times with 3% activity loss) for the hydrogenolysis of levulinic acid to -valerolactone. Compared with the mesoporous carbon without N-doping and conventional activated carbon, the introduction of N-dopant effectively improved the dispersion of Ru nanoparticles, decreased the average size of Ru nanoparticles to as small as 1.32nm, and improved the adsorption of levulinic acid, which contributed to the increase in the activity of the catalyst. Additionally, the embedding method increased the interaction between Ru nanoparticles and carbon support in contrast with the conventional impregnation method, thus preventing the Ru nanoparticles from migration, aggregation, and leaching from the carbon surface and therefore increasing the reusability of the catalyst.
Visible-Light-Promoted Selective Hydrogenation of Crotonaldehyde by Au Supported ZnAl-Layered Double Hydroxides: Catalytic Property, Kinetics, and Mechanism Investigation

Lei Fang,Wei Luo,Yue Meng,Xiaobo Zhou,Guoxiang Pan,Zheming Ni,Shengjie Xia

DOI: https://doi.org/10.1021/acs.jpcc.8b05463

2018-01-01

Abstract:alpha,beta-Unsaturated alcohols are a group of important chemicals and have frequently been synthesized by catalytic hydrogenation method due to its low cost and environmental friendly nature. However, the synthesis of high reactivity and selectivity catalyst that Visible light favors C=O hydrogenation is very challenging. Many references have reported the results of selective hydrogenation of crotonaldehyde to crotonyl alcohol, which either have high conversion and low selectivity or high selectivity and low conversion. Herein, Au-supported ZnAl-layered double hydroxides (Au/ZnAl-LDHs) were synthesized and used on the hydrogenation reaction of crotonaldehyde (CDE) to crotonyl alcohol (COL) under the moderate reaction conditions supplied with light irradiation. The experimental results indicated that the reactivity of CDE hydrogenation and selectivity of COL both have been greatly improved under visible light irradiation, from 42% to 99% for conversion of CDE, from 59.5% to 96% for COL selectivity, of COL both have been greatly improved under visible light irradiation, from 42% to 99% for conversion of CDE, from 59.5% to 96% for COL selectivity, and from 101 to 272 h(-1) for TOF, compared with no irradiation. On the basis of the proposed kinetics equation, it can be concluded that irradiation can not only remarkably increase the reaction rate of selective hydrogenation of CDE to COL but also obviously decrease the activation energy of the reaction system. The enhancement of photocatalytic property of is exactly due to the support of Au, which can be proved by the dependence of the catalytic performance on the wavelength range of light as well as the UV-vis result. In addition, the possible CDE catalytic reaction mechanism was concluded based on the calculation of surface adsorption and hydrogenation reaction path using the DFT method, which is well explained and supports the experimental results.
Catalytic Hydrogenation of Levulinic Acid to Gamma-Valerolactone over Ni/ZrO2

Dong Sheng,Jie Fu,Xiuyang Lv

2016-01-01

Abstract:Five kinds of nickel supported zirconia (Ni/ZrO2) catalysts were prepared and characterized by N2 physisorption, X-Ray diffraction and transmission electron microscope(TEM) analysis. The effects of nickel loading and different reaction conditons on the catalytic activity were studied. The results showed that the conversion of levulinic acid increased with the increase of nickel content. It was found that the highest conversion could be achieved over 50 % Ni/ZrO2 and the highest turnover frequency(TOF) was obtained over 30% Ni/ZrO2. The reaction was accelerated with the increase of reaction temperature and much favored in dioxane than in water. The highest conversion of levulinic acid (99.1%) and yield of gamma-valerolactone (91.6%) were achieved after 9 hours under the conditions of 200℃ and hydrogen pressure of 5 MPa in dioxane.
Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare Γ-Valerolactone

Jie Fu,Dong Sheng,Xiuyang Lu

DOI: https://doi.org/10.3390/catal6010006

IF: 3.9

2016-01-01

Catalysts

Abstract:Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3) with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA) to prepare γ-valerolactone (GVL). The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior to the activity in water. Nitrogen physisorption, X-ray diffraction, and transmission electron microscopy were employed to characterize the fresh and used catalysts. The effects of the nickel loading, temperature, hydrogen pressure, and substrate/catalyst ratio on the catalytic activity were investigated.
Kinetics insights into structure sensitivity of Ru catalyzed L-alanine hydrogenation to alaninol

Rui Song,Chang Yao,Wenhua Li,Nihong An,Yafeng Shen,Nina Fei,Xiaohu Ge,Yueqiang Cao,Xuezhi Duan,Xing-Gui Zhou

DOI: https://doi.org/10.1039/d4re00420e

IF: 5.2002

2024-10-19

Reaction Chemistry & Engineering

Abstract:Hydrogenations achieved on supported metal catalysts are normally structure sensitive, and comprehensive understandings on such sensitivity are pivotal for gaining insights into the active sites as well as the design of catalysts. Herein, a serials of differently sized Ru nanoparticles supported on carbon nanotube (CNT) were prepared and employed as catalysts for L-alanine hydrogenation to examine the structure sensitivity of amino acid hydrogenation. The reaction rates for L-alanine conversion and the formation of alaninol are demonstrated to be strongly dependent on the sizes of Ru nanoparticles, highlighting the structure sensitivity of the L-alanine hydrogenation. The activation energies extracted from kinetics studies are insensitive to the sizes of Ru nanoparticles on the Ru catalysts sized ≥1.3 nm with similar electronic properties, pointing to a predominant type of active site for L-alanine hydrogenation. By further combining model calculations with the shape of Ru nanoparticles determined by transmission electron microscopy, the Ru(101) sites are identified as the dominant active sites for L-alanine conversion and alaninol formation, which is further rationalized by density functional theory calculations. The kinetics insights into such structure sensitivity are believed to be important for the design and optimization of catalysts for the reaction.

chemistry, multidisciplinary,engineering, chemical
Optimization Study on Catalytic Reduction of CO2 into Formic Acid Under Hydrothermal Conditions

Jun Cheng,Tingting Si,Xin Wang,Jianzhong Liu,Junhu Zhou,Kefa Cen

DOI: https://doi.org/10.11715/rskxjs.R201608015

2017-01-01

Abstract:Catalytic reduction of CO2 into formic acid was investigated through hydrothermal reactions with Al as reducer and Ni/Cu as catalysts.A thermodynamic analysis was carried out to evaluate four potential reaction path-ways of CO2 hydrothermal reduction.It was found that the most feasible pathway was as follows:HCO3-+2,H≒HCOO-+H2O,and active H atom was the best existence state of reduced hydrogen.The influences on formic acid product and carbon conversion efficiency of molar ratios of Ni/Al,Cu/Al and Al/C,reaction time and temperature were investigated in Al-Ni and Al-Cu reaction systems.It was proved experimentally that the carbon conversion efficiency during CO2reduction into formic acid with Cu catalyst was higher than that with Ni cata-lyst.The carbon conversion efficiency was 29.1%, during CO2reduction into formic acid at 300,℃ for 120 min when the molar ratio of Al/Cu/NaHCO3was 8:8:1.
Promoting Effect of Ni on the Catalytic Production of Alanine from Lactic Acid over RuNi/AC Catalyst

Ying Liu,Lei Zhang,Shixiang Feng,Xi Chen

DOI: https://doi.org/10.1021/acs.iecr.2c01168

2022-01-01

Industrial & Engineering Chemistry Research

Abstract:A series of RuNi bimetallic catalysts supported on activated carbon were prepared to study the reductive amination of lactic acid. Among the tested catalysts, the catalyst containing 40% Ni and 60% Ru was selected as the optimal catalyst. The yield of alanine significantly increased to 64% using the Ru6Ni4 catalyst supported on an activated carbon, which was 1.5 times that using the monometallic Ru catalyst supported on an activated carbon. A number of characterization methods such as transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and temperature-programmed reduction (TPR) were used to characterize monometallic and bimetallic catalysts. The strong electron transfer between Ni and Ru and the highly dispersed structure of metal on the surface of the support contributed to the excellent catalytic performance of Ru6Ni4. The Ru6Ni4 catalyst supported on activated carbon also exhibited good activity in the reductive amination of other alpha-hydroxyl acids to corresponding amino acids.
Alkali Ions Secure Hydrides for Catalytic Hydrogenation

Ruixuan Qin,Lingyun Zhou,Pengxin Liu,Yue Gong,Kunlong Liu,Chaofa Xu,Yun Zhao,Lin Gu,Gang Fu,Nanfeng Zheng

DOI: https://doi.org/10.1038/s41929-020-0481-6

IF: 37.8

2020-01-01

Nature Catalysis

Abstract:Catalytic hydrogenation is one of the backbones of the chemical industry. Controlling the reaction behaviour of the activated hydrogen species over oxide-supported metal catalysts is essential. Aside from the expected addition to substrates, the activated hydrogen species would also destroy the active structures. Here we show that, with the assistance of alkali cations, the atomically dispersed Ru( iii ) on Al 2 O 3 exhibits enhanced performance in the hydrogenation of a broad range of substrates. The alkali cations facilitate the hydrogenation mediated by heterolytic hydrogen species, which not only restrain the hydride species from migrating to interfacial oxygen, thus suppressing the reduction and aggregation of ruthenium, but also stabilize the negatively charged transition states and intermediates through enhanced Columbic attraction. Distinctively, an inverse H/D isotope effect related to H 2 splitting as the rate-determining step over the atomically dispersed ruthenium-catalysed hydrogenation is predicted and confirmed.
Catalytic hydrogenation of aromatic ring over ruthenium nanoparticles supported on α-Al2O3 at room temperature

Wei Jiang,Jing-Pei Cao,Chen Zhu,Ming Zhao,Zhong-Hai Ni,Xiao-Yan Zhao,Jin-Xuan Xie,Liang Zhao,Yun-Peng Zhao,Hong-Cun Bai

DOI: https://doi.org/10.1016/j.apcatb.2022.121137

2022-06-01

Abstract:Selective hydrogenation of aromatic ring represents an essential process for the valorization of lignin in the chemical industry but achieving this process at low temperature is still a challenge. Herein, a series of Ru-based catalysts were investigated. It is found that Ru/γ-Al2O3 with small Ru metal particle size shows the low activity in this system. A unique and strong metal-support interaction for Ru/γ-Al2O3 indicates that the strongly bounded Ru-O-Al sites lead to the positive charge of Ru species. In contrast, Ru/α-Al2O3 with well-dispersed Ru nanoparticles supported on α-Al2O3 can successfully catalyze the selective hydrogenation of lignin-derived aromatic compounds at room temperature. Ru/α-Al2O3 has the excellent recyclability, air stability and the highest activity. The selective hydrogenation of aromatic ring for Ru/α-Al2O3 results from the fast dissociation of H2 and the high adsorption energy of aromatic ring as revealed by X-ray absorption spectra, X-ray photoelectron spectroscopy and density functional theory calculations.

chemistry, physical,engineering, chemical, environmental
Improved Catalytic Activity and Stability for Hydrogenation of Levulinic Acid by Ru/N-doped Hierarchically Porous Carbon

Zhongzhe Wei,Xuefeng Li,Jiang Deng,Jing Wang,Haoran Li,Yong Wang

DOI: https://doi.org/10.1016/j.mcat.2018.01.024

IF: 4.6

2018-01-01

Molecular Catalysis

Abstract:The catalytic transformation from levulinic acid (LA) into gamma-valerolactone (GVL) is of great interest as it is an impressive strategy to convert lignocellulosic platform chemical into high value-added compounds. Herein, a novel heterogeneous catalyst made of Ru nanoparticles (NPs) supported on N-doped hierarchically porous carbon from biomass, Ru/NHPC, was shown to be highly active, selective and stable in this transformation. The reaction can proceed smoothly under mild conditions in aqueous media even at room temperature. The catalyst Ru/NHPC could be recycled for 13 consecutive runs exhibiting no obvious activity decay, much better than that of Ru NPs supported on activated carbon. The process offers an efficient, environmentally responsible, and safe approach to high production of GVL.
Preparation of Raney Ni Catalyst and Research on Its Catalytic Hydrogenation Performance for Alkenyl Aromatics

XIA Jiajia,LUO Guohua,XU Xin,WANG Yanli,CHEN Han

DOI: https://doi.org/10.3969/j.issn.1008-1143.2013.07.013

2013-01-01

Abstract:The influence of mass ratio of pseudo-boehmite to Ni-Al alloy,nitric acid concentration,mass ratio of water to powder and calcination temperature on the strength of the catalysts was investigated.The catalysts were characterized by XRD and TG-DTA.The results illustrated that the compressive strength of the catalysts increased first and then decreased with the enhancement of mass ratio of pseudo-boehmite to Ni-Al alloy,nitric acid concentration,mass ratio of water to powder and calcination temperature.The catalyst with optimal strength was prepared under the condition as follows: mass ratio of pseudo-boehmite to Ni-Al alloy 1.5,nitric acid mass fraction 6%,mass ratio of water to powder 0.21 mL.g-1 and calcination temperature 860 ℃.The catalytic performance of the catalyst was evaluated using the hydrogenation of styrene and methylstyrene as the probe reaction.The results showed that the conversion rate of both styrene and methylstyrene could reached 100% approximately under the condition of reaction pressure 2 MPa,reaction temperature 80 ℃,reaction time 500 h,raw material space velocity 2 h-1,and V(H2) ∶ V(oil) = 300 ∶ 1.Furthermore,the catalyst stability could be maintained excellently during the whole evaluation process.
Catalytic Conversion of CO2 to Value-Added Products under Mild Conditions

Yulv Yu,Jin Huang,Yuan Wang

DOI: https://doi.org/10.1002/cctc.201801346

IF: 4.5

2018-01-01

ChemCatChem

Abstract:The catalytic synthesis of multi-carbon alcohols (MCA, CnH2n+1OH, n >= 3) and higher hydrocarbons from CO2 and H-2 under low or even ambient temperature are realized for the first time over a prepared bimetallic catalyst composed of nanoparticles of Pt and Ru supported on Fe3O4 (Ru-Pt/Fe3O4). At 40 degrees C, the selectivity for alcohols, MCA, and higher hydrocarbons reached 77.1 %, 4.5 %, and 19.5 %, respectively, while that for methane was only 3.4 % (carbon based). As revealed by isotope tracer experiments using O-18 labeled water, in the hydrogenation of CO2 over Ru-Pt/Fe3O4, MCA could form by catalytic hydrolysis of alkyl, a novel reaction pathway enabling the formation of MCA at low temperature, which is different from the previously reported one based on CO insertion at high temperature. It was discovered that in Ru-Pt/Fe3O4, both Ru and Pt nanoparticles played catalytic roles in the reduction of CO2 to CHx species and the carbon-carbon coupling reaction to form alkyl, while the catalytic hydrolysis of formed long-chain alkyl occurred on Pt nanoparticles.
Hydrogen production from ammonia decomposition over Ru/Co–Al-LDOs catalysts prepared by a one-step synthesis method of co-precipitation

Zhongrui Li,Lei Guo,Wenchen Ren,Junjie Han,Santosh Kumar Verma,Shihang Xu,Lin Liu,Tong Zhang,Yunhua Xu

DOI: https://doi.org/10.1016/j.ijhydene.2024.11.065

IF: 7.2

2024-11-13

International Journal of Hydrogen Energy

Abstract:The design of efficient ammonia cracking catalysts is the key to developing ammonia as a hydrogen storage carrier. This paper investigated the role of Co–Al hydrotalcite carriers in ruthenium-based catalysts. Ru/Co–Al catalysts were prepared by mechanical milling, impregnation, and co-precipitation, and the catalytic activity and physicochemical properties of the catalysts were investigated, respectively. The catalysts prepared by the co-precipitation method exhibit the maximum specific surface area and metal dispersion due to the layered structure of LDH and the homogeneity of the co-precipitation method. In this study, it is concluded that the substitution of Ru during the co-precipitation preparation builds up strong metal-carrier interactions and generates a large number of oxygen vacancies. The catalyst prepared by the co-precipitation method exhibited a high H 2 generation rate (19.5 mmol·gcat −1 ·min −1 ) at GHSV = 30,000 ml·gcat −1 ·h −1 and 450 °C, and the performance remained stable after 50 h of reaction. This work provides a new idea for designing efficient Ru-based catalysts.

energy & fuels,electrochemistry,chemistry, physical
Enhancement of catalytic activity of PAl-NaX catalyst for side-chain alkylation of toluene with methanol: Effects of dehydrogenation component Cu

Chengda Li,Yueli Wen,Bin Wang,Maohong Fan,Wenlong Liu,Zheng Cui,Wei Huang

DOI: https://doi.org/10.1016/j.fuel.2023.129271

IF: 7.4

2023-08-06

Fuel

Abstract:Activation and desorption of the hydrogen atom in the toluene methyl is a restrictive step for side-chain alkylation of toluene with methanol (SATM). In this work, two dehydrogenation strategies were used to improve the catalytic performance, dehydrogenation component Cu was introduced in PAl-NaX catalyst as well as the acid-base property was adjusted by changing NaOH loading amount. The relationship among the percentage of acid-base sites, low valence Cu species and the catalytic performances was investigated combined with the multiple characterizations, like X-ray photoelectron spectroscopy (XPS), Temperature-programmed desorption (TPD) of NH 3 and CO 2 , etc. together with ternary regression analysis. It is found that the dehydrogenation component Cu, especially low valence Cu species, promotes the selectivity of side-chain alkylation products to a certain degree, but base sites play an even more critical role in enhancing it.

energy & fuels,engineering, chemical
Enhanced hydrothermal stability by a semi-embedded structure: An efficient Ru catalyst for levulinic acid conversion in the aqueous phase

Yueling Cao,Haoyang Li,Fubin Ma,Hao Wen,Jinhui Wang,Hepeng Zhang

DOI: https://doi.org/10.1016/j.mcat.2024.114547

IF: 4.6

2024-09-27

Molecular Catalysis

Abstract:Catalyst stability is believed to be one of the greatest challenges faced for the supported metal catalysts in the catalytic conversion of biomass and its derivatives because many biomass transformations are conducted in the aqueous phase. In this work, we report a simple yet efficient coating-impregnation-pyrolysis (CIP) strategy to fabricate Al 2 O 3 supported Ru catalyst (Ru-Al 2 O 3 @CN) with Ru NPs (nanoparticles) semi-embedded into N-doped carbon (CN) layer for the efficient hydrogenation of levulinic acid (LA) to γ-valerolactone in the aqueous phase. Benefit from the special structure of Ru-Al 2 O 3 @CN catalyst, it possesses both high catalytic activity and stability, giving a TOF of 28,099 h -1 for LA hydrogenation at 120 °C and 2 MPa H 2 , which is superior to the most of reported Ru-based catalysts. More importantly, compared with conventional impregnated Ru/Al 2 O 3 catalyst, the Ru-Al 2 O 3 @CN catalyst exhibits a remarkably improved hydrothermal stability. Based on series of catalyst characterizations and control experiments, it was found that the presence of CN can weak the interaction between Ru and Al 2 O 3 , as well as protect the Al 2 O 3 and Ru NPs from hydrolysis and aggregation, respectively. We anticipate that such a novel strategy may provide some valuable insights into the synthesis of oxides-supported metal catalyst with high hydrothermal stability.

chemistry, physical
Influence Of Au/Tio2 Catalyst Preparation Parameters On The Selective Hydrogenation Of Crotonaldehyde

Yang Qiu-Yun,Zhu Yuan,Tian Li,Pei Yan,Qiao Ming-Hua,Fan Kang-Nian

DOI: https://doi.org/10.3866/PKU.WHXB20090906

2009-01-01

Acta Physico-Chimica Sinica

Abstract:Nanosized Au/TiO2 catalysts were prepared by the deposition-precipitation method. These catalysts were evaluated by a liquid phase hydrogenation of crotonaldehyde to crotyl alcohol and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). By changing the activation atmosphere, the Au loading, and the reduction temperature we found that the dimension of the Au particles and the metal-support interaction were readily adjustable. For the Au/TiO2 catalyst reduced at 673 K with an optimal Au mass fraction of 9.2%, the mean particle size of Au was 2 nm and the initial hydrogenation rate was as high as 1.37x10(-5) mol.s(-1).g(-1), while the maximum yield of crotyl alcohol was 69.9%. Combined with the characterization results, the superior performance of this catalyst was attributed to it having an optimal size and to its electronic modification effects on the Au nanoparticles. This was due to oxygen defects generated on the TiO2 during the reduction process.
Preparation, characterization of Ru/AlOOH catalyst and its benzene partial hydrogenation behavior

Jianqiang Wang.,PingJun Guo,Minghua Qiao,Shirun Yan,Kangnian Fan

2004-01-01

Acta Chimica Sinica

Abstract:A novel 4 wt% Ru/AlOOH catalyst was prepared by the coprecipitation method and characterized by XRD, TG/DTA, TEM and nitrogen physisorption. In liquid phase benzene partial hydrogenation, Ru/AlOOH catalyst exhibited much higher cyclohexene selectivity and moderate activity than Ru/γ-Al 2O3 catalyst prepared by calcining the titled catalyst or by the wetness impregnation method. It is suggested that the surface hydroxyl groups and the large pores in boehmite be essential for a high yield of cyclohexene.
Amination of Polylactic Acid to Alanine by Ru-Co Bimetallic Catalyst

Meng Cui,Guyue Liu,Cankun Ma,Zihan Cao,Yu Ye,Yongfu Shen,Xiu-Qin Zhang

DOI: https://doi.org/10.1039/d4nj00473f

IF: 3.3

2024-03-15

New Journal of Chemistry

Abstract:The preparation of alanine from waste polylactic acid (PLA) is not only an effective way to recycle waste plastics, but also of great significance to develop a green, clean and efficient amino acid production process. In this work, we studied the synthesis of alanine by amination of PLA with ammonia solution over different types of supported bimetallic catalysts without external hydrogen. It was found that the bimetallic catalyst consisting of Ru and non-precious metal Co supported on TiO2 (Ru-Co/TiO2) was efficient for the reaction. The selectivity of alanine and turnover frequency (TOF) were 65.2% and 1.5 h-1, respectively. The synergistic effect existed between Ru and Co catalyst was crucial for the catalytic performance, and the content of precious metal Ru in the catalyst was lower. This was the first attempt to introduce non-precious metal component into the catalyst for the amination of polylactic acid to alanine.

chemistry, multidisciplinary
Transfer Hydrogenation of Cinnamaldehyde Catalyzed by Al2O3 Using Ethanol As a Solvent and Hydrogen Donor

Huanjun Wang,Boyang Liu,Fang Liu,Yaning Wang,Xiaocheng Lan,Shiqing Wang,Babar Ali,Tiefeng Wang

DOI: https://doi.org/10.1021/acssuschemeng.0c00942

IF: 8.4

2020-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Allylic alcohols produced from α,β-unsaturated aldehydes by selective hydrogenation are useful intermediates and additives in the fine chemicals industry. An efficient process for the catalytic tra...

Optimization of Catalytic Hydrogenation L-Alanine to L-Alaninol

Liquid-phase Hydrogenation of 2,2,4,4-Tetramethyl-1,3-cyclobutanedione over Supported Ru Based Catalysts

An Efficient and Reusable Embedded Ru Catalyst for the Hydrogenolysis of Levulinic Acid to Γ‐valerolactone

Visible-Light-Promoted Selective Hydrogenation of Crotonaldehyde by Au Supported ZnAl-Layered Double Hydroxides: Catalytic Property, Kinetics, and Mechanism Investigation

Catalytic Hydrogenation of Levulinic Acid to Gamma-Valerolactone over Ni/ZrO2

Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare Γ-Valerolactone

Kinetics insights into structure sensitivity of Ru catalyzed L-alanine hydrogenation to alaninol

Optimization Study on Catalytic Reduction of CO2 into Formic Acid Under Hydrothermal Conditions

Promoting Effect of Ni on the Catalytic Production of Alanine from Lactic Acid over RuNi/AC Catalyst

Alkali Ions Secure Hydrides for Catalytic Hydrogenation

Catalytic hydrogenation of aromatic ring over ruthenium nanoparticles supported on α-Al2O3 at room temperature

Improved Catalytic Activity and Stability for Hydrogenation of Levulinic Acid by Ru/N-doped Hierarchically Porous Carbon

Preparation of Raney Ni Catalyst and Research on Its Catalytic Hydrogenation Performance for Alkenyl Aromatics

Catalytic Conversion of CO2 to Value-Added Products under Mild Conditions

Hydrogen production from ammonia decomposition over Ru/Co–Al-LDOs catalysts prepared by a one-step synthesis method of co-precipitation

Enhancement of catalytic activity of PAl-NaX catalyst for side-chain alkylation of toluene with methanol: Effects of dehydrogenation component Cu

Enhanced hydrothermal stability by a semi-embedded structure: An efficient Ru catalyst for levulinic acid conversion in the aqueous phase

Influence Of Au/Tio2 Catalyst Preparation Parameters On The Selective Hydrogenation Of Crotonaldehyde

Preparation, characterization of Ru/AlOOH catalyst and its benzene partial hydrogenation behavior

Amination of Polylactic Acid to Alanine by Ru-Co Bimetallic Catalyst

Transfer Hydrogenation of Cinnamaldehyde Catalyzed by Al2O3 Using Ethanol As a Solvent and Hydrogen Donor