Abstract:Because their topological structures have certain crystallographic symmetry, there is anisotropy in triply periodic minimal surface (TPMS) porous structures. Anisotropy can affect the mechanical properties of porous structures; thus, it is necessary to research the anisotropy of TPMS structures. In this study, based on quaternionic three-dimensional rotation, TPMS structures were rotated around three crystal directions: [100], [110], and [111]. The mechanical anisotropy behaviors of TPMS porous structures, including gyroid, diamond, primitive, and I-graph-wrapped package (IWP) graph surfaces, were studied through finite element analysis (FEA). The FEA results show that the anisotropy of the IWP structure with rotation in the [110] direction was the most significant, and its relative elastic modulus increased by 275.33% when the IWP was rotated 60° in the [110] direction. These results indicate that the uniaxial compression performance of TPMS structures can be significantly improved by using structural anisotropy. However, it should be noted that due to this significant anisotropy, the performance of such structures will significantly decrease in specific directions. For example, after the primitive structure was rotated 60° in the [111] and [110] directions, its relative elastic modulus decreased by 72.66% and 77.6%, respectively. Therefore, it was necessary to reasonably consider the bearing capacity in fragile directions under complex working conditions. Based on the anisotropy of TPMS, gradient TPMS structures with three rotation angles were designed and manufactured using selective laser melting technology. The compressive results show that multi-peaks appeared in the primitive structure with gradient rotation in the [111] direction from 0° to 40°, and step-by-step behaviors were observed in the IWP structure with gradient rotation in the [110] direction from 0° to 60°. This result shows that the yielding platform can be enhanced using gradient rotation designation based on the anisotropy of TPMS porous structures.

Investigation of Triptycene-Based Surface-Mounted Rotors

Friction and Wear Studies of Octadecyltrichlorosilane SAM on Silicon

Construction of triptycene molecular rotors with intermeshing arrangement and low rotational barrier

Triptycene Molecular Rotors Mounted On Metallofullerene Sc3c2@C-80 And Their Spin-Rotation Couplings

Characterization and Tribological Behavior of Octadecene, Dodecene and Undecenoic Acid Films on Si Substrate

2D Hexagonal Assembly of a Dipolar Rotor with a Close Interval of 0.8 nm Using a Triptycene-Based Supramolecular Scaffold

Repetitive Rolling of Triptycene-Based Molecules on Cu Surfaces

Monitoring and Manipulating Single Molecule Rotors on the Bi(111) Surface by the Scanning Tunneling Microscopy

Kinetic Modeling of Surface-Initiated Atom Transfer Radical Polymerization

Tuning Rotation Axes of Single Molecular Rotors by a Combination of Single-Atom Manipulation and Single-Molecule Chemistry.

Molecular compasses and gyroscopes. II. Synthesis and characterization of molecular rotors with axially substituted bis[2-(9-triptycyl)ethynyl]arenes

Preparation and Tribological Behaviors of an Amide-Containing Stratified Self-Assembled Monolayers on Silicon Surface

Off-Center Rotation Of Cupc Molecular Rotor On A Bi(111) Surface And The Chiral Feature

Investigation of the Tribological Behavior of 3-Mercaptopropyl Trimethoxysilane Deposited on Silicon

Metallocene: Multi-Layered Molecular Rotors.

Study on the Anisotropy of Triply Periodic Minimal Surface Porous Structures

Nanotube-based scanning rotational microscope

Formation and manipulation of diatomic rotors at the symmetry-breaking surfaces of kagome superconductors

Probing rotaxane dynamics with 19F NMR/MRI: Unveiling the roles of mechanical bond and steric hindrance

Determination of rutile transition metal oxide (110) surface terminations by scanning tunneling microscopy contrast reversal