Abstract:OBJECTIVE:To compare the registration accuracy of three-dimensional (3D) facial scans for the design of full-arch implant supported restoration by five methods and to explore the suitable registration method. METHODS:According to the criteria, ten patients with maxillary edentulous jaw or end-stage dentition requiring implant supported restorations were enrolled in this study. A special rim with individual feature marks reflected appropriate occlusal relationship and esthetic characteristics was made for each patient. Both 3D facial scan data of natural laughter and with opener traction to expose the teeth or occlusal rim of each patient were acquired by facial scan and input to the digital analysis software Geomagic Qualify 2012. The dataset was superimposed by five different methods: seven facial anatomical landmark points alignment, facial immobile area alignment (forehead and nasal area), facial anatomical landmark points and immobile area combining alignment, facial feature points alignment, facial and intraoral feature points alignment with the same local coordinate system. The three-dimensional deviation of the same selected area was calculated, the smaller the deviation, the higher the registration accuracy. The 3D deviation was compared among the three registration methods of facial anatomical landmark points, facial immobile area alignment and the combination of the above two methods. Friedman test was performed to analyze the difference among the three methods (α=0.05). The effect of the aid of the facial and intraoral feature points were evaluated. Paired t test were performed to analyze the difference (P<0.05). RESULTS:The average three-dimensional deviation of the selected area after alignment with the facial anatomical landmarks was (1.501 2±0.406 1) mm, significantly larger than that of the facial immobile area best-fit alignment [(0.629 1±0.150 6) mm] and the combination of the two methods[(0.629 1±0.150 6) mm] (P < 0.001). The aid of the facial feature points could significantly reduce the deviation (t=1.001 3, P < 0.001). There was no significant statistical difference in the remaining groups. CONCLUSION:The forehead area of the 3D facial scan can be exposed as much as possible. The establishment of facial characteristic landmark points and the use of the invariant area alignment can improve the accuracy of registration. It should be clinically feasible to apply three-dimensional facial scan to the design of full-arch implant supported restoration with the registration of the immobile area on the face especially the forehead area.

Validation of a Three-Dimensional Hand Scanning and Dimension Extraction Method with Dimension Data

Data-Driven 3-D Human Body Customization with a Mobile Device

A Novel Method for Analyzing the Influence of Relative Attitude of Laser Profile Scanner on 3D Measurement System

Digital measurement method for comparing the absolute marginal discrepancy of three-unit ceramic fixed dental prostheses fabricated using conventional and digital technologies

Error control and calibration in three-dimensional anthropometric measurement of the hand by laser scanning with glass support

Using Subject-Specific Three-Dimensional (3D) Anthropometry Data in Digital Human Modelling: Case Study in Hand Motion Simulation

Validation of a three-dimensional facial scanning system based on structured light techniques.

The Accuracy of a Three-Dimensional Face Model Reconstructing Method Based on Conventional Clinical Two-Dimensional Photos

Accuracy of Three-dimensional Scan Technology and Its Possible Function in the Field of Hand Surgery

Validation and reliability of the 3D calibration evaluation algorithm for SPM

Intra-rater and inter-rater reliability of 3D facial measurements

Reliability and validity of handheld structured light scanners and a static stereophotogrammetry system in facial three-dimensional surface imaging

Automatic Measurement of Scanned Human Body in Fixed Posture

Digital Human: Three-dimentional face model reconstruction based on Hifi3dface model with clinical two-dimentional photos

Initial validation of point cloud data from a 3D body scanner

Quantitative Evaluation Of Three-Dimensional Facial Scanners Measurement Accuracy For Facial Deformity

Refraction Effect Analysis of Using A Hand-Held Laser Scanner with Glass Support for 3d Anthropometric Measurement of the Hand: A Theoretical Study

Accuracy Evaluation of a New Three-Dimensional Reproduction Method of Edentulous Dental Casts, and Wax Occlusion Rims with Jaw Relation.

Quantitative evaluation of the measurement accuracy of 2 three-dimensional facial scanners

Evaluation of the Accuracy, Reliability, and Reproducibility of Two Different 3D Face-Scanning Systems

Comparison of the Registration Methods for the Three-Dimensional Facial Scans Applied to the Design of Full-Arch Implant Supported Restoration