Abstract:The microstructure, aging behavior and mechanical properties of cast Mg–3Nd–3Gd– x Zn–0.5Zr ( x = 0, 0.5, 0.8, 1 wt%) alloys are investigated in this work. Zn–Zr particles with different morphologies form during solution treatment due to the additions of Zn. As the Zn content increases, the number density of Zn–Zr particles also increases. Microstructural comparisons of peak-aged studied alloys indicate that varying Zn additions could profoundly influence the competitive precipitation behavior. In the peak-aged Zn-free alloy, β′′ phases are the key strengthening precipitates. When 0.5 wt% Zn is added, besides β′′ precipitates, additional fine β 1 precipitates form. With the addition of 0.8 wt% Zn, the peak-aged 0.8Zn alloy is characterized by predominantly prismatic β 1 and scanty basal precipitate distributions. The enhanced precipitation of β 1 should be primarily attributable to the presence of increased Zn–Zr dispersoids. When Zn content further increases to 1 wt%, the precipitation of basal precipitates is markedly enhanced. Basal precipitates and β 1 phases are the key strengthening precipitates in the peak-aged 1Zn alloy. Tensile tests reveal that the relatively best tensile properties are achieved in the peak-aged alloy with 0.5 wt% Zn addition, whose yield strength, ultimate tensile strength and elongation are 179 MPa, 301 MPa and 5.3%, respectively.

Chemical Composition Optimization of Gravity Cast Mg–yNd–xZn–Zr Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructural Characteristics and Mechanical Properties of Cast Mg–3Nd–3Gd–xZn–0.5Zr Alloys

Effects of chemical composition on the microstructure and mechanical properties of gravity cast Mg-xZn-yRE-Zr alloy

Microstructure and Mechanical Properties of Mg–3.0Y–2.5Nd–1.0Gd–x Zn–0.5Zr Alloys Produced by Metallic and Sand Mold Casting

High cycle fatigue properties of cast Mg– x Nd–0.2Zn–Zr alloys

Effect of Zn Addition on Microstructure and Mechanical Properties of Mg–9Gd–3Y–0.5Zr Alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effects of Minor Y Addition on Microstructure and Mechanical Properties of Mg-Nd-Zn-Zr Alloy

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Microstructural Evolution and Mechanical Performance of Cast Mg-3Nd-0.2Zn-0.5Zr Alloy with Y Additions

Achieving High Mechanical Performance of the Large-Scale Sand-Casting Mg–4Y–x Nd–y Gd–0.4Zr Alloys by Tailoring Nd and Gd Contents

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Microstructure and Mechanical Properties of Mg-7Zn-3Al Alloy with Nd and Y Additions

Microstructures and mechanical properties of as-cast Mg–5Y–3Nd–Zr–xGd (x=0, 2 and 4wt.%) alloys

Precipitation modification in cast Mg–1Nd–1Ce-Zr alloy by Zn addition

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Microstructure and Mechanical Properties of Mg–4.5Zn–xNd (x=0, 1 and 2, Wt%) Alloys

Influence of Zn on the microstructure and mechanical properties of Mg-Gd-Zr alloy