Abstract:Noncovalently cross-linked hydrogels can exhibit toughness and mechanical adaptability typically associated with biological tissues, which make them promising for a variety of applications. However, molecules in the environment can interact to significantly alter the properties of these hydrogels, which could adversely impact their performance. Here, we illustrate how two common ionic surfactants, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB), influence the swelling and rheological properties of hydrogel films cross-linked by hydrophobic associations based on a random copolymer of poly(N,N-dimethylacryalmide-co-2-(N-ethylperfluorooctanesulfonamido)ethyl acrylate (DMA-FOSA) using a quartz crystal microbalance with dissipation (QCM-D). The effect of the surfactants on the swelling and dissolution of these physically crosslinked hydrogels is contrasted with the effect of aqueous 2-propanol (IPA), which can dissolve the copolymer readily. The addition of IPA, SDS, and CTAB at low concentrations increases the swelling of the hydrogel film, decreases the elastic modulus, and increases the rheological phase angle (more fluidlike). A transition from swelling to (partial) dissolution occurs at higher concentrations with a threshold of approximately 7 wt % IPA, 0.1.cmc for SDS, and 0.5.cmc for CTAB to promote partial dissolution. With IPA, initial swelling is always observed immediately after the solvent is added, whereas the initial swelling can be significantly delayed with long incubation times to dissolution, on the order of hours, at low concentrations of surfactant. These results illustrate that simple ionic surfactants can dissolve these hydrophobically cross-linked hydrogels, but identification of the maximum concentration of surfactant that will not dissolve the hydrogels may be challenged by the long incubation times that increase as the concentration decreases. The long times to dissolve these thin films (initial thickness <200 nm for copolymer) suggest that stability of bulk physically cross-linked hydrogels in complex aqueous environments may be challenging to accurately assess if surfactant diffusion is the limiting factor.

Water-assisted Formation of Honeycomb Films of Poly(L-lactic-co-glycolic Acid)

Amphiphilic Block Copolymers Based on Methoxy Poly(ethylene Glycol) and Either Crystalline or Amorphous Poly(caprolactone‐b‐lactide): Synthesis, Solid‐state and Aqueous Solution Characterizations

A study on formation of regular honeycomb pattern in polysulfone film

Systematic Investigation on the Formation of Honeycomb-Patterned Porous Films from Amphiphilic Block Copolymers

Fabrication of Honeycomb-Patterned Polyalkylcyanoacrylate Films from Monomer Solution by Breath Figures Method

Formation and Control of Honeycomb Microporous Structure in High Humidity

Controlled Synthesis of Linear and Comb-Like Glycopolymers for Preparation of Honeycomb-Patterned Films

Fabrication of polymeric honeycomb microporous films: breath figures strategy and stabilization of water droplets by fluorinated diblock copolymer micelles

Porous Morphology and Mechanical Properties of Poly(lactide-Co-glycolide) Hollow Fiber Membranes Governed by Ternary-Phase Inversion

Honeycomb-Structured Microporous Films Made From Hyperbranched Polymers By The Breath Figure Method

Delayed Swelling and Dissolution of Hydrophobically Associated Hydrogel Coatings by Dilute Aqueous Surfactants

Pore Shape of Honeycomb-Patterned Films: Modulation and Interfacial Behavior

Tuning the Surface Hydrophobicity of Honeycomb Porous Films Fabricated by Star-Shaped POSS-fluorinated Acrylates Polymer Via Breath-Figure-templated Self-Assembly

Functionalization of Honeycomb-Patterned Films

Fabrication of Adsorption-Type Hierarchical Functional Films by Using a Facile Swollen Based Breath Figure Method.

Preparation of Poly (l‐lactic Acid) with Aligned Structures by Unidirectional Freezing

Polystyrene with Hydrophobic End Groups: Synthesis, Kinetics, Interfacial Activity, and Self-Assemblies Templated by Breath Figures

Fabrication of Ordered Honeycomb Amphiphobic Films with Extremely Low Fluorine Content

Using A Breath-Figure Method to Self-Organize Honeycomb-Like Polymeric Films from Dendritic Side-Chain Polymers

Nano-hydroxyapatite promotes self-assembly of honeycomb pores in poly(L-lactide) films through breath-figure method and MC3T3-E1 cell functions

Preparation of Honeycomb Films from Nitryl Poly(ether Ether Ketone)s Via Water‐droplet Templating