Abstract:Ultra-high nickel single-crystal cathode materials have become the most promising for lithium-ion batteries. However, the preparation of ultra-high nickel single-crystal precursors by a continuous coprecipitation method has the disadvantages of large particle size, wide distribution, poor morphology. The extent of the inhomogeneous reactions can be more severe in single-crystal cathodes with larger particle size. Herein, the coprecipitation method with a solid concentrator was adopted, and citrate sodium was used as a complexing agent to improve the physical properties of precursors and electrochemical performance of single-crystal cathode materials. By analyzing the morphology and agglomeration mechanism of the precursor nucleuses under different pH values, it was found that hexagonal nanosheets grew along the 101 direction, and the primary particles showed thicker at pH of 11.4. The hexagonal nanosheets grew along the 001 direction, and the primary particles showed finer at pH of 12.2. The morphology and particle size uniformity of the secondary particles formed by agglomeration at these two pH values showed poor. However, hexagonal nanosheets grew synergistically along the 001 and 101 directions at pH of 11.8, so the primary particles with uniform particle size gradually agglomerated, and then the secondary particles with ultra-small particle size and uniform distribution obtained. Compared to materials prepared by the traditional continuous coprecipitation method, the precursor displays a smaller particle size(D50 = 1.8 µm), higher sphericity, uniformity and denser internal structure. In order to evaluate the performance of Ni0.94Co0.04Mn0.02(OH)2 with ultra-small particle size, the sintering conditions of LiNi0.94Co0.04Mn0.02O2 need to be explored. It was found that the LiNi0.94Co0.04Mn0.02O2 cathode material prepared at 790 °C exhibited higher discharge capacity, cycle and rate performance, compared to materials prepared at 760 °C and 820 °C. We further utilized TEM, EPMA, and XPS to test the internal structure and valence state of LiNi0.94Co0.04Mn0.02O2 cathode material. The results show that the LiNi0.94Co0.04Mn0.02O2 calcined at 790 °C has a good single crystal structure. The LiNi0.94Co0.04Mn0.02O2 cathode materials inherited the structure and particle size of Ni0.94Co0.04Mn0.02(OH)2 precursors, and displayed discharge capacity of 194.7 mAh/g and capacity retention rate of 89.8 % after 100 cycles at 1 C. The microstructure and phase transition of the as-prepared cathode material are well-maintained after long-term cycling, without obvious inter-crystalline micro-crack. The results indicate that its electrochemical performance is better than that of cathode materials with precursors prepared by a continuous coprecipitation method. This work provides new insights for the preparation of small-particle-size precursor and single-crystal cathode materials.

Controlled Crystallization and Granulation of Nano-Scale Β-Ni(oh)2 Cathode Materials for High Power Ni-MH Batteries

Granulation of Nano-Scale Ni(Oh)(2) Cathode Materials for High Power Ni-Mh Batteries

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Ton-scale preparation of single-crystal Ni-rich ternary cathode materials for high-performance lithium ion batteries

Preparation and Electrochemical Behavior of Nano Β-Ni(oh)2

Controlled Synthesis of Single-Crystalline Ni-Rich Cathodes for High-Performance Lithium-Ion Batteries

Synthesis of nanoscale CoO particles and their effect on the positive electrodes of nickel–metal hydride batteries

Controlled crystallization of spherical active cathode materials for Ni-MH and lithium ion rechargeable batteries

Controlled crystallization of spherical active cathode materials for NiMH and Li ion rechargeable batteries

High-rate Dischargeability Enhancement of Ni/MH Rechargeable Batteries by Addition of Nanoscale CoO to Positive Electrodes

Highly‐Dispersed Single‐Crystalline Ni‐Rich Cathodes with Low Li/O Loss for High‐Power and Long‐Life Li‐Ion Batteries

Boosting discharge capability of α-Ni(OH)2 by cobalt doping based on robust spherical structure

Al2O3-Coated, Single Crystal Zr/Y co-Doped High-Ni NCM Cathode Materials for High-Performance Lithium-Ion Batteries

Nanostructured LiNi<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>O<sub>2</sub>as a cathode material for high-power lithium-ion battery

Nanostructured LiNi1/3Co1/3Mn1/3O2as a Cathode Material for High-Power Lithium-Ion Battery

Application of precursor with ultra-small particle size and uniform particle distribution for ultra-high nickel single-crystal cathode materials by coprecipitation method

Preparation of NCM622 cathode materials using nanoscale porous NiO material

Nano-Crystalline Li1.2Mn0.6Ni0.2O2 Prepared Via Amorphous Complex Precursor and Its Electrochemical Performances As Cathode Material for Lithium-Ion Batteries

Introducing an Efficient and Eco-Friendly Spray-Drying Process for the Synthesis of NCM Precursor for Lithium-ion Batteries

Synthesis of Single Crystal LiNi 0.92 Co 0.06 Mn 0.01 Al 0.01 O 2 Cathode Materials with Superior Electrochemical Performance for Lithium Ion Batteries

High-rate discharge properties of nickel hydroxide/carbon composite as positive electrode for Ni/MH batteries