Introduction for the Super-low Spectral Analysis

Jun-hua ZHANG,Wei ZHANG,Zhong-qi PU

DOI: https://doi.org/10.3969/j.issn.1001-1390.2006.01.001

2006-01-01

Abstract:Spectral analysis of unevenly sampled data is proposed to get information of the frequency which is below the minimum discriminating frequency.Simulation result is given.Discusses the case where this method is applied and its advantage and disadvantage.

What problem does this paper attempt to address?

Analysis and Application of Digital Spectrum of Ultrasonic Testing System

JIANG Zhi-feng,LIU Ji-zhong,ZHOU Xiao-jun

DOI: https://doi.org/10.3969/j.issn.1001-3881.2005.01.047

2005-01-01

Abstract:The theory and application of ultrasonic digital spectrum was analyzed.Though signal sampling,A/D transformation, and time-frequency transformation, spectrum parameter produced by ultrasonic response was obtained.The factors of spectrum that influence system characteristic were analyzed,it is of great importance to the establishment of analysis system of high-quality signal.
Spectral Analysis in Linear Process Identification—a New Look at an Old Problem

YC ZHU,MH KLOMPSTRA

DOI: https://doi.org/10.1080/00207179108953685

IF: 2.102

1991-01-01

International Journal of Control

Abstract:The problem of estimating the transfer function (frequency response) of a linear process by means of a modified spectral analysis method is treated. A method of determining the maximum time lags of the correlation functions which makes use of the available a priori physical knowledge about the process and the input signal is proposed. This leads, in a natural way, to the use of an asymmetrical window technique. Some simulation results are used to illustrate the method. Based on the asymptotic properties of the estimate, the input design is studied. Finally it will be shown that this work can be used for the estimation of an upper bound of the model uncertainty in the frequency domain.
Low SNR FMCW Signal Processing with Prior Information.

Qing Wen Hou,Zhi Wei Xu,Zhen Long Bai,Xian Zhong Chen,Jing Ni Wang

DOI: https://doi.org/10.1007/978-3-642-42057-3_79

2015-01-01

Abstract:Aiming at the range ambiguity problem of wideband and low SNR (signal-to-noise ratio) FMCW (frequency modulated continuous wave) signals under severe measurement conditions, a solid surface FMCW signal model is built. Besides, based on prior information, a distance inversion method is proposed, which contains signal pretreatment, band intercepting and energy weighting. Actual data processing results show that, SNR of the frequency spectrum has been raised from -5.55dB to 8.32dB after pretreatment; and the final results show that index of similarity of stock level shape respectively raised from 0.46 to 0.71 and 0.79.
A NSZT Method for Frequency Estimation and Anti-noise Performance Analysis

Wenxin Zhang,Xiaojun Liu,Xiuwei Chen,Qing Liu,Guangyou Fang

DOI: https://doi.org/10.1049/cje.2017.10.007

IF: 1.019

2018-01-01

Chinese Journal of Electronics

Abstract:Among all the frequency estimation algorithm, the spectrum zooming method has superiority for high resolution and excellent anti-noise performance, but it needs more computational resource. The typical spectrum zooming methods include Zoom fast Fourier transform (ZFFT), Chirp-Z transform (CZT) and zeropadding, which are all uniform spectrum zooming methods. A Nonuniform spectrum zooming transform ...
An UBSS Method for Signals with Non-Uniform Energy Distribution of Varied Frequency Bins

Naixin Chen,Chunli Zhu,Lei Chen

DOI: https://doi.org/10.1109/IECON51785.2023.10311827

2023-01-01

Abstract:Coupled signals sensing from electromechanical systems have significant impacts on the intelligent fault diagnosis application, which is generally formulated as an undertermined blind source separation (UBSS) issue. However, it is especially challenging when dealing with signals of non-uniform energy distribution of different frequency bins. In this work, we proposed an UBSS framework with an adaptive optimal frequency bin selection approach, for improving the signal sparsity and estimation accuracy of the mixing matrix. Simulation results show that the proposed method achieves average accuracy of 82.40%, 86.91 % and 87.19% with the signal-to-noise ratio (SNR) set as 10, 15 and 30 <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\text{dB}$</tex> of the tested case, respectively. This work has a good potential on reducing the intelligent state monitoring system's false alarm rate.
Spectral Factorization for Integer-Interval Sampled Sequence and Its Applications in Array Processing

Zhu Liang Yu,Meng Hwa Er,Wee Ser,Zhenghui Gu

DOI: https://doi.org/10.1016/j.sigpro.2008.01.010

IF: 4.729

2008-01-01

Signal Processing

Abstract:Spectral factorization (SF) has been well developed for a uniformly sampled sequence (USS). Our recent study found important applications of SF for a non-uniformly sampled sequence (NUSS) in array processing, especially considering arbitrary arrays. Since SF for an arbitrarily sampled sequence is intractable, in this paper, we propose a new SF method for an integer-interval sampled sequence (IISS). Its applications in robust adaptive beamforming and array pattern synthesis for a non-uniform linear array (NULA) are studied. Simulation results show the outstanding performance of the proposed method.
A Novel Algorithm for Implementing Time-Frequency Transform with Low Computation.

Yijiao Zhang,Shulin Tian,Huiqing Pan,Duyu Qiu,Lianping Guo

DOI: https://doi.org/10.1063/5.0018793

2021-01-01

Abstract:In this paper, a novel algorithm called two-dimensional sliding fast Fourier transform (2D SFFT) algorithm is proposed. This algorithm organizes one-dimensional data in two dimensions and calculates the spectrum of current data by using the existing spectrum and new collected data. The algorithm formula and accurate simulation results show the following: first, the computation required by the proposed 2D SFFT algorithm is lower than that required by the traditional sliding discrete Fourier transform algorithm when the sliding rate is larger than or equal to 4/M, where M is the sequence length. Moreover, the computation required by the proposed 2D SFFT algorithm is lower than that required by the fast Fourier transform (FFT) algorithm when the sliding rate is less than or equal to 6.25%. Finally, the error between the spectrum calculated by the 2D SFFT and FFT algorithms is less than 10-10. The 2D SFFT algorithm is used to increase the power of the ultra-short pulse, which is initially invisible in the frequency-domain window of the mixed-domain oscilloscope. Therefore, the 100% probability of intercept of the mixed-domain oscilloscope is lower.
Unsupervised Feature Selection Using Nonnegative Spectral Analysis.

Zechao Li,Yi Yang,Jing Liu,Xiaofang Zhou,Hanqing Lu

DOI: https://doi.org/10.1609/aaai.v26i1.8289

2012-01-01

Abstract:In this paper, a new unsupervised learning algorithm, namely Nonnegative Discriminative Feature Selection (NDFS), is proposed. To exploit the discriminative information in unsupervised scenarios, we perform spectral clustering to learn the cluster labels of the input samples, during which the feature selection is performed simultaneously. The joint learning of the cluster labels and feature selection matrix enables NDFS to select the most discriminative features. To learn more accurate cluster labels, a nonnegative constraint is explicitly imposed to the class indicators. To reduce the redundant or even noisy features, l2,1-norm minimization constraint is added into the objective function, which guarantees the feature selection matrix sparse in rows. Our algorithm exploits the discriminative information and feature correlation simultaneously to select a better feature subset. A simple yet efficient iterative algorithm is designed to optimize the proposed objective function. Experimental results on different real world datasets demonstrate the encouraging performance of our algorithm over the state-of-the-arts.
SCAN-MUSIC: An Efficient Super-resolution Algorithm for Single Snapshot Wide-band Line Spectral Estimation

Zetao Fei,Hai Zhang

2023-10-27

Abstract:We propose an efficient algorithm for reconstructing one-dimensional wide-band line spectra from their Fourier data in a bounded interval $[-\Omega,\Omega]$. While traditional subspace methods such as MUSIC achieve super-resolution for closely separated line spectra, their computational cost is high, particularly for wide-band line spectra. To address this issue, we proposed a scalable algorithm termed SCAN-MUSIC that scans the spectral domain using a fixed Gaussian window and then reconstructs the line spectra falling into the window at each time. For line spectra with cluster structure, we further refine the proposed algorithm using the annihilating filter technique. Both algorithms can significantly reduce the computational complexity of the standard MUSIC algorithm with a moderate loss of resolution. Moreover, in terms of speed, their performance is comparable to the state-of-the-art algorithms, while being more reliable for reconstructing line spectra with cluster structure. The algorithms are supplemented with theoretical analyses of error estimates, sampling complexity, computational complexity, and computational limit.

Signal Processing
Profile Detection for Fiber Spectrum Data with Low SNR Based on Wavelet and Filtering

Zhu, Zhangqin,Zhu, Jia,Zhongfu Ye

DOI: https://doi.org/10.1109/cisp.2010.5648080

2010-01-01

Abstract:In this paper, a novel detection method is proposed for fiber spectrum profile signals with low signal-to-noise ratio (SNR). This method can be applied to the processing of astronomical fiber spectrum data. First, profile signal of the target is decomposed into several sub-signals by stationary wavelet transform (SWT) algorithm. For sub-signals, adaptive filters are designed with their respective cutoff frequencies by using the corresponding reference signal (flat signal) in order to separate noise from target signal for getting more accurate information of the signal. Inverse stationary wavelet transform (ISWT) is used to reconstruct the detection signal. At the end of this paper, experiments for different full width at half-maximum (FWHM) of point-spread functions (PSF) are presented to demonstrate the effectiveness of the proposed method.
Realization of the measurement of a single-tone periodic signal’s amplitude and frequency based on undersampling

Ning Fu,Rui Shi,Lingyun Song,Zhiwei Wang

DOI: https://doi.org/10.19652/j.cnki.femt.2015.10.015

2015-01-01

Abstract:A signal’s amplitude and frequency can be measured by sampling and analysis .However ,according to Nyquist sampling theorem ,it is difficult to capture high‐frequency signals with the method of Over‐sampling limited by the sam‐pling rate .To obtain a signal’s amplitude and frequency by a low sampling rate ,design a method within which the ampli‐tude and frequency of a signal‐tone periodic signal can be measured by Under‐sampling .Take a self‐developed data acqui‐sition card as the hardware platform ,take advantage of a sampling rate of 100 MSa/s to measure the amplitude and fre‐quency of a signal‐tone periodic signal which is located in a bandwidth of 100 M Hz to 150 M Hz by FFT operation and curve‐fitting .The test result makes clear that this method has high accuracy .In addition ,with this method ,there is no need to recover the original signal ,and the hardware is easy to implement ,the software bears small amount of calculation as well .This method is particularly suitable for measuring the amplitude and frequency of a signal‐tone periodic signal w hich is located in a narrow band .
A Faster and Accurate Method for Spectral Testing Applicable to Noncoherent Data

Minshun Wu,Degang Chen,Guican Chen

DOI: https://doi.org/10.1109/naecon.2010.5712927

2010-01-01

Abstract:The Fast Fourier Transform is the standard approach for spectral testing. However, its correct application to sinusoidal signals requires either strict coherent sampling, or careful windowing, or other methods that are not computationally efficient. This paper introduces an improved method for achieving accurate and robust spectral testing for sinusoidal signals without the need for coherent sampling or windowing. Theoretical analysis, extensive simulation results, and experimental results show that the proposed method is always faster than the original method and robust when the signal frequency is close to Nyquist frequency. Statistical analysis and comparative studies demonstrate that the proposed algorithm achieves almost the same spectral testing accuracies as those obtained under perfect coherent sampling.
Fast Spectrum Analysis for an Ofdr Using the Fft and Sczt Combination Approach

Cheng Ma,Qian Zhou,Jie Qin,Weilin Xie,Yi Dong,Weisheng Hu

DOI: https://doi.org/10.1109/lpt.2015.2504120

IF: 2.6

2016-01-01

IEEE Photonics Technology Letters

Abstract:Spectrum analysis is a significant process for many measurement applications which is usually implemented by fast Fourier transform (FFT). Nevertheless, FFT is not suitable to deal with big data because of extra burden of computation. Moreover, FFT fails to provide enough accuracy for signals with a very sparse and broadband spectral distribution. In this letter, we propose a combination approach called FFT-segmented chirp-Z transform that allows to analyze a long-time signal, while the data are received, achieving faster speed, better resolution with only small memory size which shows great potential in real-time performance. With the help of this approach, zoom bands are detected, and optimal parameters are established to guarantee peaks in a broadband spectrum can be found in short time with high precision. We implement this approach in a high spatial resolution optical frequency-domain reflectometry to realize high speed and high precision of components localization in optical fiber. The experimental result shows that 2-mm spatial resolution is achieved at a distance of 54 m and the processing time was less than 2 s for 10(7) data points.
A Novel Way of Improving Spectra Analysis Precision with Nonuinform Sampling

Yi Jiang,Tianxiang Gu

DOI: https://doi.org/10.3321/j.issn:0254-3087.2005.12.019

2005-01-01

Abstract:Spectra analysis is a basic way of signal analysis. A new spectra analysis way is proposed through investigating some effective ways of improving spectral analysis inside and outside country. The method can improve spectral analysis precision without adding hardware or sampling data with a double-speed sampling nonuniform sequence. Its validity is tested by computer simulation.
Analysis of Adaptive Short-time Fourier Transform-based Synchrosqueezing Transform

Haiyan Cai,Qingtang Jiang,Lin Li,Bruce W. Suter

DOI: https://doi.org/10.48550/arXiv.1812.11033

2018-12-28

Abstract:Recently the study of modeling a non-stationary signal as a superposition of amplitude and frequency-modulated Fourier-like oscillatory modes has been a very active research area. The synchrosqueezing transform (SST) is a powerful method for instantaneous frequency estimation and component separation of non-stationary multicomponent signals. The short-time Fourier transform-based SST (FSST for short) reassigns the frequency variable to sharpen the time-frequency representation and to separate the components of a multicomponent non-stationary signal. Very recently the FSST with a time-varying parameter, called the adaptive FSST, was introduced. The simulation experiments show that the adaptive FSST is very promising in instantaneous frequency estimation of the component of a multicomponent signal, and in accurate component recovery. However the theoretical analysis of the adaptive FSST has not been carried out. In this paper, we study the theoretical analysis of the adaptive FSST and obtain the error bounds for the instantaneous frequency estimation and component recovery with the adaptive FSST and the 2nd-order adaptive FSST.

Numerical Analysis
Study of low-frequency ultrasonic cavitation fields based on spectral analysis technique

Zhaofeng Liang,Guangping Zhou,Shuyu Lin,Yihui Zhang,Hongli Yang

DOI: https://doi.org/10.1016/j.ultras.2005.09.001

IF: 4.2

2006-01-01

Ultrasonics

Abstract:A kind of new spectral analysis method for analyzing ultrasonic cavitation fields is brought forward in this paper. This method extracts the line spectrum and the continuous spectrum from the cavitation noise spectrum respectively, then obtains estimations of the energy intensities of different cavitation components such as the stable cavitation and the transient cavitation through corresponding calculations. The method is also applied to investigate low-frequency ultrasonic cavitation fields and is compared with spectral level analysis method. The results show that this method can provide adequate information on the course of the cavitation process, give the delicate analysis on the transient cavitation and the stable cavitation, and help to gain an insight into the nonlinear process of cavitation fields. Moreover, it also shows that the criterion for characterization of cavitation intensity presented by Frohly through studying the high-frequency ultrasonic fields can be used to evaluate the low-frequency ultrasonic fields.

acoustics,radiology, nuclear medicine & medical imaging
Research on the Amplitude Nonuniformly Sampled Signals' digital Spectra

Mao-liu LIN,Ben-zhao XIE,Tai-fan QUAN

DOI: https://doi.org/10.3321/j.issn:0372-2112.2000.05.007

2000-01-01

Tien Tzu Hsueh Pao/Acta Electronica Sinica

Abstract:In the high speed digitizers with time-interleaved structure, the input signal's amplitude is sampled nonuniformly because of the offset and gain difference of A/D. The paper first defines the concept of amplitude nonuniformly sampled signal, studies the digital spectrum of the amplitude nonuniformly sampled signal, derives its digital spectra representation and furthermore presents a detailed spectrum analysis of an amplitude nonuniformly sampled sinusoid, to obtain the signal-to-noise ratio. At last, the results of computer simulation that verify the correction of the above theory are given.
Spectral Detection of a Weak Frequency Band Signal Based on the Pre-Whitening Scale Transformation of Stochastic Resonance in a Symmetric Bistable System in a Parallel Configuration

Zhijun Qin,Tengfei Xie,Chen Xie,Di He

DOI: https://doi.org/10.3390/electronics13183637

IF: 2.9

2024-09-12

Electronics

Abstract:The spectral detection of weak frequency band signals poses a serious problem in many applications, especially when the target is within a certain frequency band under low signal-to-noise ratio (SNR) conditions. A kind of novel technique based on the pre-whitening scale transformation of stochastic resonance (SR) in a symmetric bistable system in a parallel configuration is proposed to solve the problem. Firstly, pre-whitening can ensure the Gaussian distribution of the receiving signal fits the requirements for SR processing. Secondly, scale transformation can help to effectively utilize the properties of a weak signal, especially under a low-frequency band. Thirdly, the SR in a symmetric bistable system in a parallel configuration can try to smoothly reduce the variances in the clutter and additive noise. Fourthly, by subtracting the steady state response of the SR in the selected symmetric bistable system from the parallel output, the spectral detection of a weak signal can be realized successfully. Experiment results based on actual sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

engineering, electrical & electronic,computer science, information systems,physics, applied
Non-uniform Fourier Spectrum Sampling for Improving Performance of Imaging

Kaiyu Zhang,Jie Cao,Fanghua Zhang,Fei Wang,Yahui Jiang

DOI: https://doi.org/10.1117/12.2543464

2019-01-01

Abstract:To enhance the performance of Fourier single-pixel imaging using lower data, we propose a non-uniform spectrum sampling for FSI instead of the traditional uniform spectrum sampling. The principle is deduced, and the corresponding simulations are conducted to verify and evaluate the performance of our strategy. Results show that non-uniform spectrum sampling for FSI is feasible. Meanwhile, compared with the traditional spectrum acquisition strategy, our strategy shows an advantage in measurement efficiency and high reconstruction image quality under the same sampling ratio. Our proposed strategy has a good application prospect in video acquisition, multispectral hyperspectral imaging or other high speed and high precision field.
Spectra in low-rank localized layers (SpeLLL) for interpretable time-frequency analysis

Marie Tuft,Martica H Hall,Robert T Krafty

DOI: https://doi.org/10.1111/biom.13577

IF: 1.701

Biometrics

Abstract:The time-varying frequency characteristics of many biomedical time series contain important scientific information. However, the high-dimensional nature of the time-varying power spectrum as a surface in time and frequency limits its direct use by applied researchers and clinicians for elucidating complex mechanisms. In this article, we introduce a new approach to time-frequency analysis that decomposes the time-varying power spectrum in to orthogonal rank-one layers in time and frequency to provide a parsimonious representation that illustrates relationships between power at different times and frequencies. The approach can be used in fully nonparametric analyses or in semiparametric analyses that account for exogenous information and time-varying covariates. An estimation procedure is formulated within a penalized reduced-rank regression framework that provides estimates of layers that are interpretable as power localized within time blocks and frequency bands. Empirical properties of the procedure are illustrated in simulation studies and its practical use is demonstrated through an analysis of heart rate variability during sleep.

Introduction for the Super-low Spectral Analysis

Analysis and Application of Digital Spectrum of Ultrasonic Testing System

Spectral Analysis in Linear Process Identification—a New Look at an Old Problem

Low SNR FMCW Signal Processing with Prior Information.

A NSZT Method for Frequency Estimation and Anti-noise Performance Analysis

An UBSS Method for Signals with Non-Uniform Energy Distribution of Varied Frequency Bins

Spectral Factorization for Integer-Interval Sampled Sequence and Its Applications in Array Processing

A Novel Algorithm for Implementing Time-Frequency Transform with Low Computation.

Unsupervised Feature Selection Using Nonnegative Spectral Analysis.

SCAN-MUSIC: An Efficient Super-resolution Algorithm for Single Snapshot Wide-band Line Spectral Estimation

Profile Detection for Fiber Spectrum Data with Low SNR Based on Wavelet and Filtering

Realization of the measurement of a single-tone periodic signal’s amplitude and frequency based on undersampling

A Faster and Accurate Method for Spectral Testing Applicable to Noncoherent Data

Fast Spectrum Analysis for an Ofdr Using the Fft and Sczt Combination Approach

A Novel Way of Improving Spectra Analysis Precision with Nonuinform Sampling

Analysis of Adaptive Short-time Fourier Transform-based Synchrosqueezing Transform

Study of low-frequency ultrasonic cavitation fields based on spectral analysis technique

Research on the Amplitude Nonuniformly Sampled Signals' digital Spectra

Spectral Detection of a Weak Frequency Band Signal Based on the Pre-Whitening Scale Transformation of Stochastic Resonance in a Symmetric Bistable System in a Parallel Configuration

Non-uniform Fourier Spectrum Sampling for Improving Performance of Imaging

Spectra in low-rank localized layers (SpeLLL) for interpretable time-frequency analysis