Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Plastic Instability and Strain Rate Sensitivity of Ultrafine-Grained Iron

Microstructures And Properties Of Ultrafine Grained Iron By Rolling

Plastic Yielding and Tensile Strength of Near-Micrometer Grain Size Pure Iron

Microstructures and Mechanical Properties of Commercial Purity Iron Processed by Asymmetric Rolling

Grain Boundary Sliding and Strain Rate Sensitivity of Coarse and Fine/Ultrafine Grained 5083 Aluminum Alloys

Effects of nanocrystalline and ultrafine grain sizes on constitutive behavior and shear bands in iron

Hall-Petch relationship of interstitial-free steel with a wide grain size range processed by asymmetric rolling and subsequent annealing

Effect of Strain Rate on the Tensile Behavior of Ultra-Fine Grained Pure Aluminum

Deformation Behavior and Plastic Instabilities of Ultrafine-Grained Titanium

Effect of Grain Size and Residual Strain on the Dynamic Transformation of Austenite under Plate Rolling Conditions

Microstructures and Deformation Behavior of Nano-Grained and Ultrafine-Grained High-Mn Austenitic Steel Fabricated by Asymmetric-Symmetric Rolling

Effect of nanocrystalline and ultrafine grain sizes on the strain rate sensitivity and activation volume: fcc versus bcc metals

Strain Hardening and Strain Rate Sensitivity of Ultrafine-Grained Metals

Study of microstructures and deformation behavior of ultrafine-grained high-Mn TWIP steel fabricated by heavily asymmetric-symmetric rolling

Shear Deformation and Grain Refinement in Pure Al by Asymmetric Rolling

Mechanical Properties and Microstructures of Ultrafine-Grained Pure Aluminum by Asymmetric Rolling

Crystal Plasticity-Based Assessment of Constitutive Laws for Microstructure and Rolling Texture Capture in Ferritic Stainless Steel During Cold Rolling

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Strain Rate Sensitivity of Low‐Temperature Superplastic Heterogeneous Medium‐Mn Steel Fabricated by a Novel High‐Ratio Differential Speed Rolling

Strain hardening, strain rate sensitivity, and ductility of nanostructured metals

Testing and Modeling the Effect of Strain-Rate on Plastic Anisotropy for A Traditional High Strength Steel