Uncorrelated Beat Noise Measurement for Optical Signal-to-noise Ratio Monitoring

Chen, W.,Tucker, RodneyS.,Xingwen Yi,Shieh, William

DOI: https://doi.org/10.1049/cp:20050807

2005-01-01

Abstract:We present theoretical analysis and experimental demonstration of a new optical signal-to-noise ratio (SNR) monitoring method using uncorrelated beat noise. The measurement errors are less than 0.6 dB in a 10 Gb/s system.

What problem does this paper attempt to address?

Optical Signal-to-noise Ratio Monitoring Using Uncorrelated Beat Noise

W Chen,RS Tucker,XW Yi,W Shieh,JS Evans

DOI: https://doi.org/10.1109/lpt.2005.858100

IF: 2.6

2005-01-01

IEEE Photonics Technology Letters

Abstract:We propose and experimentally demonstrate a new technique for monitoring optical signal-to-noise ratio (OSNR). The noisy signal to be measured is split into two paths. With offset optical bandpass filters and balanced radio-frequency subtraction after detection, the signal is separated from the beat noise. OSNR can then be monitored by analyzing this beat noise. An experiment for a 10-Gb/s system shows that for OSNR in the range of 10-30 dB, the proposed OSNR monitoring scheme produces errors of less than 0.5 dB.
Analyses of Noncommensurate Sampling Used in High-Precision Regenerative Pseudo-Noise Ranging Systems

Zhao-bin Xu,Xiao-jun Jin,Chao-jie Zhang,Zhong-he Jin

DOI: https://doi.org/10.1007/s11771-014-2025-1

2014-01-01

Journal of Central South University

Abstract:A high-precision pseudo-noise ranging system is often required in satellite-formation missions. But in an actual PN ranging system, digital signal processing limits the ranging accuracy, only level up with meter-scale. Using non-integer chip to sample time ratio, noncommensurate sampling was seen as an effective solution to cope with the drawback of digital effects. However, researchers only paid attention to selecting specific ratios or giving a simulation model to verify the effectiveness of the noncommensurate ratios. A qualitative analysis model is proposed to characterize the relationship between the range accuracy and the noncommensurate sampling parameters. Moreover, a method is also presented which can be used to choose the noncommensurate ratio and the correlation length to get higher phase delay distinguishability and lower range jitter. The simulation results indicate the correctness of our analyses and the optimal ranging accuracy can be up to centimeter-level with the proposed approach.
EVM Estimation for Performance Monitoring in Coherent Optical Systems: an Approach of Linear Regression

Yuchuan Fan,Xiaodan Pang,Aleksejs Udalcovs,Carlos Natalino,Lu Zhang,Sandis Spolitis,Vjaceslavs Bobrovs,Richard Schatz,Xianbin Yu,Marija Furdek,Sergei Popov,Oskars Ozolins

DOI: https://doi.org/10.1364/cleo_si.2022.sw4e.8

2022-01-01

Abstract:We experimentally demonstrate the effectiveness of a simple linear regression scheme for optical performance monitoring when applied after modulation format identification. It outperforms the FFNN-based benchmark scheme providing 0.2% mean absolute error for EVM estimation.
A Novel Method to Monitor OSNR Using a Mach-Zehnder Interferometer

ZN Tao,ZY Chen,LB Fu,DM Wu,AS Xu

DOI: https://doi.org/10.1109/cleopr.2001.971084

2001-01-01

Abstract:We introduce a novel technique to monitor optical signal to noise ratio (OSNR) in optical transport networks using a Mach-Zehnder interferometer. The experiments show that the method has high accuracy and large dynamic range. The error is less than 0.5 dB for OSNR between 10 dB to 40 dB in the best case. The key advantage of this method is its low cost.
OSNR monitoring for QPSK and 16-QAM systems in presence of fiber nonlinearities for digital coherent receivers

Zhenhua Dong,Alan Pak Tao Lau,Chao Lu

DOI: https://doi.org/10.1364/OE.20.019520

2012-08-13

Abstract:OSNR monitoring is indispensable for coherent systems to ensure robust, reliable network operation and potentially enable impairment-aware routing for future dynamic optical networks. In a long-haul transmission link with chromatic dispersion (CD) and fiber nonlinearity, it is difficult to distinguish between amplifier noise and fiber nonlinearity induced distortions from received signal distributions even after various transmission impairment compensation techniques, thus resulting in grossly inaccurate OSNR estimates. Based on the received signal distributions after carrier phase estimation (CPE), we propose to characterize the nonlinearity-induced amplitude noise correlation across neighboring symbols and incorporate such information into error vector magnitude (EVM) calculation to realize fiber nonlinearity-insensitive OSNR monitoring. For a transmission link up to 1600 km and signal launched power up to 2 dBm, experimental results for 112 Gb/s polarization-multiplexed quadrature phase-shift keying (PM-QPSK) demonstrate an OSNR monitoring range of 10-24 dB with a maximum estimation error below 1 dB. For 224 Gb/s PM-16-quadrature amplitude modulation (PM-16-QAM) systems, simulation results demonstrate an OSNR monitoring range of 18-28 dB with a maximum estimation error below 1 dB. Tolerance of the proposed OSNR monitoring technique to different pulse shapes, timing phase offsets, polarization dependent loss (PDL), polarization-mode dispersion (PMD) and WDM effects are also investigated through simulations.
Measurement of In-Band Optical Noise Spectral Density

Sylvain Almonacil,Matteo Lonardi,Philippe Jenneve,Nicolas Dubreuil

DOI: https://doi.org/10.48550/arXiv.2107.04426

2021-07-09

Abstract:We present a method to measure the spectral density of in-band optical transmission impairments without coherent electrical reception and digital signal processing at the receiver. We determine the method's accuracy by numerical simulations and show experimentally its feasibility, including the measure of in-band nonlinear distortions power densities.

Signal Processing,Optics
Monitoring of OSNR by Using a Mach–Zehnder Interferometer

ZN Tao,ZY Chen,LB Fu,DM Wu,AS Xu

DOI: https://doi.org/10.1002/mop.1221

IF: 1.311

2001-01-01

Microwave and Optical Technology Letters

Abstract:We introduce a novel technique to monitor the optical signal‐to‐noise ratio (OSNR) using a Mach–Zehnder interferometer. The error of the novel method is less than 0.5 dB when the OSNR is between 10 and 40 dB in the best working case. In practice, the dynamic range reduces to 10–30 dB because of the influence of polarization, crosstalk, and signal bit rate. The key advantage of this method is its low cost. © 2001 John Wiley & Sons, Inc. Microwave Opt Technol Lett 30: 63–65, 2001.
Simultaneous Monitoring of CD and OSNR Based on Delay-Tap Sampling and Image Processing

Jinsheng Xu,Jian Zhao,Tianhua Xu,Kenneth K. Y. Wong

DOI: https://doi.org/10.1109/icocn53177.2021.9563899

2021-01-01

Abstract:We demonstrated a simultaneous CD and OSNR monitoring method for NRZ-OOK signals by employing the delay-tap sampling and image processing techniques. The monitoring ranges of OSNR and CD are 14–30 dB and 0–1275 ps/nm, respectively.
Enhancing the monitoring sensitivity of DOP-based OSNR monitors in high OSNR region using off-center narrow-band optical filtering.

Guo-Wei Lu,Lian-Kuan Chen

DOI: https://doi.org/10.1364/OE.15.000823

IF: 3.8

2007-01-01

Optics Express

Abstract:Recently, OSNR monitoring based on the measurement of degree of polarization (DOP) has attracted much attention, thanks to its simplicity and high efficiency. However, the OSNR monitoring sensitivity is quite poor in the high OSNR region, resulting in high estimation error and narrow dynamic range. In this paper, we propose and experimentally demonstrate a narrow-band off-center optical filtering technique for DOP-based OSNR monitors. In 40-Gb/s RZ-OOK systems, OSNR monitoring sensitivity and DOP dynamic range are successfully enhanced to 3.14%/dB and 31.4%, respectively, in the high OSNR region (25 similar to 35dB/0.1nm). (c) 2007 Optical Society of America.
ANN/Random Forest Based Performance Monitoring in High-Speed Short-Reach Optical Interconnections

Jian Zhao,Zihao Su,Yuqing Yang,Tianhua Xu

DOI: https://doi.org/10.1016/j.yofte.2024.103941

IF: 2.8

2024-01-01

Optical Fiber Technology

Abstract:In this work, we have developed signal quality monitoring approaches in 100/400 Gbit/s short-reach transmission systems, with the application of four advanced modulation formats. In 100G and 400G transmission systems, it is shown that accuracies of 100 % have been achieved in the modulation format identification (MFI), with the use of random forest (RF) and multitask learning-based artificial neural network (MTL-ANN) for the four modulation formats mentioned. Meanwhile, average mean-square errors (MSEs) of the monitored optical signal-to-noise ratio (OSNRs) are less than 0.1 dB. Random forest uses up to 29 adders and 190 comparators, reducing its complexity by two orders of magnitude compared to MTL-ANN.
Miniature Optical Signal Transmission System for PDN Noise Measurement

Luo Guang-xiao,Zhang Wei-dong,Wei Xing-chang

DOI: https://doi.org/10.1109/apemc.2016.7522771

2016-01-01

Abstract:A method is presented to design and analysis the miniature optical signal transmission system which can be used in the complex electromagnetic environment. By combination the diode spice model with CCCS (Current-Controlled Current Source), the simplified circuit model is created to analysis the whole measurement system. The measurement shows that the system attenuation is (−32±0.5) dB from DC to 1.1GHz, agree with the design results. At last, this optical system is used to obtain the waveforms of electro-static discharge and PDN noise, the results of measurement and simulation validate the suggested design and analysis method.
Longitudinal gOSNR Monitoring by Receiver-side Digital Signal Processing in Multi-Span Optical Transmission System

Choloong Hahn,Junho Chang,Zhiping Jiang

2023-10-11

Abstract:We propose the world first longitudinal gOSNR estimation by using correlation template method at Rx, without any monitoring devices located in the middle of the link. The proposed method is experimentally demonstrated in a 12-span link with commercial transceiver.

Signal Processing
Optical Performance Monitoring Based on Asynchronous Sampling Technology

PJ Wen,HM Zhang,MY Yao,H Wang,M Yan

DOI: https://doi.org/10.1117/12.574959

2005-01-01

Abstract:Optical performance monitoring is a very import issue in the optical transparent network. We present an optical performance monitoring method, based on asynchronous sampling technology, and Q value and bit error rate can be calculated by the asynchronous histogram. Experiment result shows that the optical performance method is bit rate transparent and modulate format transparent.
Optical Performance Monitoring in Transparent Fiber-Optic Networks Using Neural Networks and Asynchronous Amplitude Histograms

Jinsheng Xu,Jian Zhao,Sheng Li,Tianhua Xu

DOI: https://doi.org/10.1016/j.optcom.2022.128305

IF: 2.4

2022-01-01

Optics Communications

Abstract:Recently, technologies such as artificial neural networks (ANNs) and asynchronous amplitude histograms (AAHs) are widely employed in the optical performance monitoring (OPM). In this paper, the number of layers and the optimization of the neural networks are investigated to complete a series of monitoring tasks in optical communication systems with a large range of chromatic dispersion (CD) and optical signal-to-noise ratio (OSNR). It is shown that the monitoring accuracy has been significantly improved with such implementations. Numerical simulations, which have been conducted for six different modulation formats, demonstrate a good monitoring performance, with an average OSNR monitoring error of 0.1064 dB (99.49% monitoring accuracy) for the OSNR range of 10-40 dB and an average CD monitoring error of 3.3324 ps/nm (99.45% monitoring accuracy) for the CD range of 170-1870 ps/nm, respectively. Furthermore, the CD monitoring and the modulation format identification (MFI) have also been investigated for the system with a large range of dispersion. An average CD error of 16.6832 ps/nm (99.45% monitoring accuracy) and a 100% MFI accuracy have been achieved for all six modulation formats. This scheme is also verified experimentally with OSNR errors of 0.41 dB and CD errors of 15.21 ps/nm, respectively. The identification accuracy of the three modulation formats in the experimental system is also 100%.
Long Short-Term Memory Neural Network (LSTM-NN) Enabled Accurate Optical Signal-to-Noise Ratio (OSNR) Monitoring

Chunxiao Wang,Songnian Fu,Zhuopeng Xiao,Ming Tang,Deming Liu

DOI: https://doi.org/10.1109/jlt.2019.2904263

IF: 4.7

2019-08-15

Journal of Lightwave Technology

Abstract:Optical signal-to-noise ratio (OSNR) monitoring is essential to both the operation of reliable and reconfigurable network and the supply of high quality-of-service. Recently, deep learning technique has been proposed for the implementation of OSNR monitoring. However, the potential of deep learning technique for OSNR monitoring has not been fully exploited in terms of the monitoring accuracy and robust operation. Here, we propose an OSNR monitoring scheme with high accuracy and short response time using the long short-term memory neural network (LSTM-NN). The use of LSTM-NN is helpful to identify the relationship between the time-varied data and corresponding OSNR without manual feature extraction. We investigate the optimal number of time steps for the LSTM-NN-based OSNR monitoring and the monitoring accuracy with respect to various modulation formats with variable baud-rates. Finally, we implement an experimental verification for 34.94-GBd polarization division multiplexing-16 quadrature amplitude modulation signal, achieving a mean absolute error of 0.05 dB over the OSNR range from 15 to 25 dB. The advantages of LSTM-NN-based OSNR monitoring include high accuracy and smart response, which is ideal for future agile optical network.

engineering, electrical & electronic,optics,telecommunications
Real-Time Eye Diagram Monitoring for Optical Signals Based on Optical Sampling

Tao Huang,Zhiqiang Fan,Jun Su,Qi Qiu

DOI: https://doi.org/10.3390/app13031363

2023-01-01

Abstract:Featured Application The proposed real-time eye diagram monitoring method has potential applications in modern optical communications and cloud computations. A real-time eye diagram monitoring method for optical signals is proposed and experimentally demonstrated based on optical sampling. In the system, the optical signals under test are directly sampled by an optical sampling pulse train with a narrow pulse width and a high repetition frequency. The sampling pulse train is achieved in a Mach-Zehnder modulator (MZM), gated on-off by an electrical pulse. The sampled optical signals are then broadened and detected by a photodetector (PD). A low-speed electrical analog-to-digital converter (ADC) will then quantify the detected electrical signals. Combining with an algorithm based on the infinitesimal calculus, the quantified data is then used to achieve the eye diagram, according to which more time-domain parameters, such as period, time jitter, Q value, and bit error rate (BER) for the optical signals under test, are obtained. Thanks to the high repetition rate of the optical sampling pulse train, the eye diagram and the time-domain parameters of the optical signals are observed in real time. Experimental results show that a real time of about 350-mu s eye diagram monitoring for a 2.5-Gb/s optical signal with a dynamic range from -10 to -22 dBm is achieved. In addition, time jitters are measured to range from 4.3 to 49.8 ps. Q values are estimated to range from 20.4 to 4.3, corresponding to BERs ranging from 2.3 x 10(-92) to 8.5 x 10(-6). The results are also verified by a commercial real-time oscilloscope.
SNR Enhancement for Comparator-Based Ultra-Low-Sampling Φ-OTDR System Using Compressed Sensing

Zhenyu Xiao,Xiaoming Li,Haofei Zhang,Xueguang Yuan,Yang-An Zhang,Yuan Zhang,Zhengyang Li,Qi Wang,Yongqing Huang

DOI: https://doi.org/10.3390/s24113279

IF: 3.9

2024-05-22

Sensors

Abstract:The large amount of sampled data in coherent phase-sensitive optical time-domain reflectometry (Φ-OTDR) brings heavy data transmission, processing, and storage burdens. By using the comparator combined with undersampling, we achieve simultaneous reduction of sampling rate and sampling resolution in hardware, thus greatly decreasing the sampled data volume. But this way will inevitably cause the deterioration of detection signal-to-noise ratio (SNR) due to the quantization noise's dramatic increase. To address this problem, denoising the demodulated phase signals using compressed sensing, which exploits the sparsity of spectrally sparse vibration, is proposed, thereby effectively enhancing the detection SNR. In experiments, the comparator with a sampling parameter of 62.5 MS/s and 1 bit successfully captures the 80 MHz beat signal, where the sampled data volume per second is only 7.45 MB. Then, when the piezoelectric transducer's driving voltage is 1 Vpp, 300 mVpp, and 100 mVpp respectively, the SNRs of the reconstructed 200 Hz sinusoidal signals are respectively enhanced by 23.7 dB, 26.1 dB, and 28.7 dB by using compressed sensing. Moreover, multi-frequency vibrations can also be accurately reconstructed with a high SNR. Therefore, the proposed technique can effectively enhance the system's performance while greatly reducing its hardware burden.

engineering, electrical & electronic,instruments & instrumentation,chemistry, analytical
Highly-Sensitive Phase and Frequency Noise Measurement Technique Using Bayesian Filtering

Darko Zibar,Hou-Man Chin,Yeyu Tong,Nitin Jain,Joel Guo,Lin Chang,Tobias Gehring,John E. Bowers,Ulrik L. Andersen

DOI: https://doi.org/10.1109/lpt.2019.2945051

IF: 2.6

2019-01-01

IEEE Photonics Technology Letters

Abstract:Spectral purity of laser sources is typically investigated using phase or frequency noise measurements, which require extraction of the optical phase. This is a challenging task if the signal-to-noise-ratio (SNR) of the spectral line or the linewidth-to-noise-ratio (LNR) are not sufficiently high. In this letter, we present a statistically optimal method for optical phase noise measurement that relies on coherent detection and Bayesian filtering. The proposed method offers a record sensitivity, as the optical phase is measured at a signal power of -75 dBm (SNR of -11 dB in 1.1 GHz receiver bandwidth). Practically, this means that the phase noise measurements are, up to a high-degree, not limited by the measurement noise floor. This allows measurements down to -200 dB rad(2)/Hz and up to 10 GHz, which is useful when measuring the Schawlow-Townes (quantum noise limited) laser linewidth. Finally, the estimated optical phase is highly accurate allowing for quantum limited signal demodulation. The method thus holds the potential to become a reference measurement tool.
Modulation Format and Optical Signal-to-Noise Ratio Monitoring for Cognitive Optical Wireless Communications

Alberto Pepe,Zixian Wei,Xin Liu,H. Y. Fu

2019-01-01

Abstract:We propose a method to monitor modulation format and signal-to-noise ratio via convolutional neural networks. The processing of constellation diagrams for a highly distorted, multipath fading channel enables cognitive transceivers in optical wireless communication links.

Uncorrelated Beat Noise Measurement for Optical Signal-to-noise Ratio Monitoring

Optical Signal-to-noise Ratio Monitoring Using Uncorrelated Beat Noise

Analyses of Noncommensurate Sampling Used in High-Precision Regenerative Pseudo-Noise Ranging Systems

EVM Estimation for Performance Monitoring in Coherent Optical Systems: an Approach of Linear Regression

A Novel Method to Monitor OSNR Using a Mach-Zehnder Interferometer

OSNR monitoring for QPSK and 16-QAM systems in presence of fiber nonlinearities for digital coherent receivers

Measurement of In-Band Optical Noise Spectral Density

Monitoring of OSNR by Using a Mach–Zehnder Interferometer

Simultaneous Monitoring of CD and OSNR Based on Delay-Tap Sampling and Image Processing

Enhancing the monitoring sensitivity of DOP-based OSNR monitors in high OSNR region using off-center narrow-band optical filtering.

ANN/Random Forest Based Performance Monitoring in High-Speed Short-Reach Optical Interconnections

Miniature Optical Signal Transmission System for PDN Noise Measurement

Longitudinal gOSNR Monitoring by Receiver-side Digital Signal Processing in Multi-Span Optical Transmission System

Optical Performance Monitoring Based on Asynchronous Sampling Technology

Optical Performance Monitoring in Transparent Fiber-Optic Networks Using Neural Networks and Asynchronous Amplitude Histograms

Long Short-Term Memory Neural Network (LSTM-NN) Enabled Accurate Optical Signal-to-Noise Ratio (OSNR) Monitoring

Real-Time Eye Diagram Monitoring for Optical Signals Based on Optical Sampling

SNR Enhancement for Comparator-Based Ultra-Low-Sampling Φ-OTDR System Using Compressed Sensing

Highly-Sensitive Phase and Frequency Noise Measurement Technique Using Bayesian Filtering

Modulation Format and Optical Signal-to-Noise Ratio Monitoring for Cognitive Optical Wireless Communications