Abstract:Fabrication of a periodic plasma density structure in a gas jet with a boundary scale length approaching 10 μm was demonstrated. This technique has potential applications in various transient high-field plasma photonic devices. The capability of fabrication of gas/plasma density structures is the key to the development of plasma photonic devices such as plasma-based particle accelerators, x-ray lasers, high-harmonic generation, plasma nonlinear optics, etc. For instance, in the development of laser wakefield electron accelerator, it was proposed that by creating a sharp downward density ramp in the plasma, background electrons can be injected into the plasma wave at the ramp. In the development of high harmonic generation from gases, quasi-phase matching by using periodically interlaced layers of highand low-density gas or plasma was proposed to increase the conversion efficiency. The main obstacle for the realization of these ideas is that a gas/plasma density structure with a scale length of below 100 μm cannot be achieved by mechanical shaping of the gas jet nozzle, neither can a three-dimensional structure. In this work, we show that a density structure in a gas jet with a boundary scale length approaching 10 μm can be fabricated by direct optical machining. Although the desired structure only exists transiently (~10 ns), it is effectively static as far as the action of the photonic device is concerned (<100 ps). We demonstrated this by fabricating a periodically modulated gas/plasma density distribution. The idea for the fabrication of a periodic plasma density structure in a gas jet is as follows. When a spatially periodic laser intensity pattern is produced in the neutral gas jet, if the average laser intensity is set at the intensity threshold of optical-field ionization, plasma is formed only at the high intensity regions. At several nanoseconds after the heating of the plasma by the same pulse through above-threshold-ionization heating or by a subsequent long heater pulse though inverse bremsstrahlung heating, the plasma has dissipated as a result of hydrodynamic expansion. This leads to the creation of a periodic distribution of interlacing layers of high-density neutral gas and low-density plasma. The capability of producing a very sharp structure results from that optical-field ionization (multi-photon ionization) is a highly nonlinear process. A 10 TW, 55 fs, 810 nm, and 10 Hz Ti:sapphire laser system based on chirped-pulse amplification was used in this experiment. A compressed laser beam was split into two. One with 80% energy served as a longitudinal probe beam, and the other with 20% energy was used as the machining pulse. The machining pulse was set to be 7-ns earlier than the longitudinal probe and its energy was tunable with a half-wave plate and a thin-film polarizer. The longitudinal probe beam was focused by an f/7.2 off-axis parabolic mirror to a focal spot of 7 μm diameter in full width at half maximum (FWHM) with 80% energy enclosed in a Gaussian-fit profile. It was set to propagate in the same path as the pump pulse that will be used to drive various plasma photonic devices. Perpendicular to the probe pulse, the machining pulse right after passing through the mask was imaged horizontally onto the interaction plane by a cylindrical lens of 20 cm focal length with a demagnification factor of 8, and focused vertically by a cylindrical lens of 30 cm focal length to produce a line width of 20 μm FWHM. The line-shaped machining beam overlapped the propagation path of the longitudinal probe beam. An imaging system was used to measure the intensity distribution of the machining beam on the interaction plane. The intensity patterns of this machining pulse for using masks of various periods are shown in Fig. 1. With masks of different periods, we can produce a machining beam with a horizontal intensity modulation of 250 μm, 100 μm, and 40 μm period, respectively. The gas target was produced from a pulsed valve with a supersonic conical nozzle. The density profile has a 1-mm flat-top region with 250-μm boundaries. The atom density increased linearly with increasing backing pressure and reached 2.5×10 cm at 800-psi backing pressure for hydrogen gas. Side imaging of Thomson scattering from electrons was used to observe the laser channel of the longitudinal probe pulse. Since the intensity of Thomson scattering is proportional to the product of laser intensity and electron density, it can be used to measure the electron density distribution when the laser intensity distribution is known.

Density modulation produced by lase r pulses at modest intensities and induced phase reflection in underdense plasmas

Density Modulation Produced by Ultrashort Laser Pulses and the Phase Reflection Induced in Underdense Plasmas

Vacancy of Laser Field Induced by Phase Reflection in Underdense Plasmas and Its Relation to Laser-Plasma Parameters

Surface Plasma Wave Excited by Laser Pulse Obliquely Incident on a Double-Layer Plasma Target and Ts Application

Model Study on Laser Interaction with Near-Critical Density Plasma

Effect of Density Modulation on Backward Stimulated Raman Scattering in A Laser-Irradiated Plasma

Plasma Density Gratings Induced by Intersecting Laser Pulses in Underdense Plasmas

Self-compression and splitting of laser pulse in plasmas

Effects Of Laser And Plasma Parameters On Shock Wave Generation And Acceleration Of Protons

Target Density Effects on Charge Transfer of Laser-Accelerated Carbon Ions in Dense Plasma

Density modulation-induced absolute laser-plasma-instabilities: simulations and theory

Laser Propagation in Dense Magnetized Plasma

Collective absorption of laser radiation in plasma at sub-relativistic intensities

Influence of Under-Dense Plasma on Laser Conical Target Interaction

Target density effects on charge tansfer of laser-accelerated carbon ions in dense plasma

Enhancement of Guided Electromagnetic Wave by Pre-Plasma Formation in Laser–plasma Interaction

Fabrication of transient plasma density structures for plasma photonic devices

Intensity-Dependent Resonance Absorption in Relativistic Laser-Plasma Interaction

Laser opacity in underdense preplasma of solid targets due to quantum electrodynamics effects.

Self-compression of laser pulses induced by asymmetric self-phase modulation aided by backward Raman scattering in periodic density-modulated plasma

Theory of the ultra-intense short-pulse laser interaction with under-dense plasma