Abstract:Abstract Background Pedicle screw placement in patients with osteoporosis is a serious clinical challenge. The bone mineral density (BMD) of the screw trajectory has been positively correlated with the screw pull-out force, while the computer tomography (CT) value has been linearly correlated with the BMD. The purpose of this study was to establish an in vitro osteoporosis model and verify the accuracy and effectiveness of automated pedicle screw planning software based on CT values in this model. Methods Ten vertebrae (L1-L5) of normal adult pigs were randomly divided into decalcification and control groups. In the decalcification group, the vertebral bodies were decalcified with Ethylenediaminetetraacetic acid (EDTA) to construct an in vitro osteoporosis model. In the decalcification group, automatic planning (AP) and conventional manual planning (MP) were used to plan the pedicle screw trajectory on the left and right sides of the pedicle, respectively, and MP was used on both sides of the control group. CT values of trajectories obtained by the two methods were measured and compared. Then, 3D-printed guide plates were designed to assist pedicle screw placement. Finally, the pull-out force of the trajectory obtained by the two methods was measured. Results After decalcification, the BMD of the vertebra decreased from − 0.03 ± 1.03 to − 3.03 ± 0.29 (P < 0.05). In the decalcification group, the MP trajectory CT value was 2167.28 ± 65.62 Hu, the AP trajectory CT value was 2723.96 ± 165.83 Hu, and the MP trajectory CT value in the control group was 2242.94 ± 25.80 Hu (P < 0.05). In the decalcified vertebrae, the screw pull-out force of the MP group was 48.6% lower than that of the control group (P < 0.05). The pull-out force of the AP trajectory was 44.7% higher than that of the MP trajectory (P < 0.05) and reached 97.4% of the MP trajectory in the control group (P > 0.05). Conclusion Automatic planning of the pedicle screw trajectory based on the CT value can obtain a higher screw pull-out force, which is a valuable new method of pedicle screw placement in osteoporotic vertebre.

Effect of EDTA-Na2 Decalcification to Simulate Osteoporosis and Drilling on the Alteration of Bone Mineral Density

The effects of Alendronate on bone mineral density in RA patients with osteoporosis or osteopenia

Effect of lumbar nerve dorsal roots section on the rat bone structural changes of lower limb

Effects of Electro-Acupuncture with Different Frequency on Space Structures of Cancellous Bone in the Ovariectomized Rat Model

Measurement of Bone Density in Rat Model of Osteoporosis

An Experimental Study on Bone Decalcification in the Process of Sample Prepara Tion for Electron Microscopy by Using Ultrasonic Irradiation

Bone mineral density and bone mineral content in the lumbar vertebrae and the vetebra's biomechanical properties

Effect of Exponential Curve Electric Stimulus on the Treatment of Primary Osteoporosis

Effect of Hyperbaric Oxygenation and Static Magnetic Fields on Bone Mineral Density in Ovariectomized Rats

Effect of zoledronic acid on blood lipid and bone mineral density in postmenopausal females

Effect of abdominal adipose content on spine phantom bone mineral density measured by rapid kilovoltage-switching dual-energy CT and quantitative CT

Study of Ibandronate and Alendronate Treatment for Postmenopausal Osteoporosis

Effect of Bone Mass, Microarchitecture and Impact Direction on Biomechanical Properties of Bone in Ovariectomy-Induced Osterporotic Rats

The Accuracy and Effectiveness of Automatic Pedicle Screw Trajectory Planning Based on Computer Tomography Values: an in Vitro Osteoporosis Model Study.

The morphological study of the effect of genistein on bone metabolism

Effect of Xian Ling Compound on Estrogen Level,bone Mineral Density and Bone Morphology in Ovariectomized Rats

[Effects of Enzymatic Bone Powder on Calcium Absorption and Bone Density in Rats].

The Effects of Calcitonin Treatment on Bone Quality in Patients Withosteoporosis

Diagnostic Accuracy of Dual-Energy CT Material Decomposition Technique for Assessing Bone Status Compared with Quantitative Computed Tomography

Assessment of Bone Quality Using Finite Element Analysis Based Upon Micro-CT Images

Effects of tetrahedral DNA nanostructures on the treatment of osteoporosis