Abstract:Background Medical examinations or treatment of pregnant women using ionizing radiation are sometimes unavoidable. In such cases, the risk of harm to the embryo and fetus after exposure to ionizing radiation must be carefully estimated. However, no commercially available anthropomorphic body phantoms of pregnant women are available for dose measurements. A promising possibility for the production of body phantoms for patient groups that are not adequately represented by the phantoms of reference persons is 3D printing. However, this approach is still in the evaluation phase. Purpose To print the abdomen of a woman in the late stage of pregnancy and compare the dose distribution measured using thermoluminescence dosimeters (TLDs) in the printed phantom for two different computed tomography (CT) protocols with the corresponding results of Monte Carlo simulations on voxel models of the pregnant woman. Materials and methods The physical phantom was produced through multi‐material extrusion printing using different print materials identified in previous studies to simulate homogeneous soft tissues and the mean compositions of maternal and fetal bones. The 3D printed abdomen was combined with a conventionally produced anthropomorphic female phantom to obtain a whole‐body phantom of a pregnant woman. Dose values resulting from two different CT scans acquired at tube voltages of 80 and 120 kV were measured using TLDs positioned in the physical phantom and cross‐validated with the results of Monte Carlo simulations performed for two different voxel models. The first was a voxelized model of the produced phantom itself and the second a realistic digital model of a pregnant woman. Representative CT values of the materials used in the printed phantom were determined from the acquired CT images. Results The CT values of maternal and fetal tissue structures in the phantom are comparable to CT values of real human tissues. The difference between most organ doses measured in the 3D printed phantom and simulated in the voxel models was below 20% and equivalent within the measurement uncertainties. Only the dose to the fetal head was up to 50% higher and not equivalent for the realistic model and the 80 kV‐protocol. As expected, the agreement was better for the voxelized than for the realistic model. For both models a slight energy dependence was observed, with larger deviations for the 80‐kV protocol especially for organs located in the pelvic region. Conclusion Individualized physical body phantoms, such as that of a pregnant woman, can be produced using 3D printing. The good agreement between measured and simulated doses to the fetus cross‐validates both dosimetric methods. Therefore, this study demonstrates the suitability of 3D printing phantoms for patients not adequately represented by commercially available body phantoms of reference persons.

Development of a 30-Week-pregnant Female Tomographic Model from Computed Tomography (CT) Images for Monte Carlo Organ Dose Calculations.

The Development, Validation and Application of A Multi-Detector Ct (mdct) Scanner Model for Assessing Organ Doses to the Pregnant Patient and the Fetus Using Monte Carlo Simulations

Patient-specific Fetal Radiation Dosimetry for Pregnant Patients Undergoing Abdominal and Pelvic CT Imaging.

Construction of a computational model of pregnant patients with twins for radiation dosimetry

Construction of Personalized Computational Phantoms of Pregnant Patients for Assessment of CT Radiation Dose

Specific Absorbed Fractions For Internal Photon Emitters Calculated For A Tomographic Model Of A Pregnant Woman

Patient-Specific Computational Model and Dosimetry Calculations for PET/CT of a Patient Pregnant with Twins.

A Boundary-Representation Method for Designing Whole-Body Radiation Dosimetry Models: Pregnant Females at the Ends of Three Gestational Periods--rpi-p3, -P6 and -P9.

WE-C-AUD-06: Radiation Safety of Pregnant Patients During Radiation Treatment: A Detailed Modeling of the Accelerator, Patient Anatomy, and Non-Target Doses

Development of Computational Pregnant Female and Fetus Models and Assessment of Radiation Dose from Positron-Emitting Tracers

Assessment of CT Dose to the Fetus and Pregnant Female Patient Using Patient-Specific Computational Models.

Hybrid computational pregnant female phantom construction for radiation dosimetry applications

Fetal and Maternal Absorbed Dose Estimates for Positron-Emitting Molecular Imaging Probes.

Construction of a digital fetus library for radiation dosimetry

Estimation of the Radiation Dose in Pregnancy: an Automated Patient-Specific Model Using Convolutional Neural Networks

Fetal Doses to Pregnant Patients from CT with Tube Current Modulation Calculated Using Monte Carlo Simulations and Realistic Phantoms

3D printing of realistic body phantoms: Comparison of measured and simulated organ doses on the example of a CT scan on a pregnant woman

TH-C-201B-12: CT Dose Reduction with Tube Current Modulation: A Case Study of Fetal Doses to Pregnant Patients Using Monte Carlo Computational Phantoms

Construction of Patient-Specific Computational Models for Organ Dose Estimation in Radiological Imaging.

A Feasibility Study to Calculate Unshielded Fetal Doses to Pregnant Patients in 6-MV Photon Treatments Using Monte Carlo Methods and Anatomically Realistic Phantoms.

Fetus dose calculation during proton therapy of pregnant phantoms using MCNPX and MCNP6.2 codes