Abstract:The preparation and characterization of nanocomposites of poly(vinylidene fluoride), PVDF, with acid treated multiwalled carbon nanotubes (MWCNT) with a wide composition range, from 0.1 to 5.0% MWCNT by weight, is reported. Effect of uniaxial orientation by zone drawing on these nanocomposites is discussed and compared with unoriented compression molded films. Static room temperature two-dimensional wide angle X-ray scattering and Fourier transform infrared spectroscopy were used for phase identification. Differential scanning calorimetry, polarizing optical microscopy, dynamic mechanical analysis (DMA), and thermogravimetic analysis (TGA) were used to study the thermal and mechanical properties. Incorporation of MWCNT into PVDF has no obvious effect in forming beta phase crystal in the PVDF/MWCNT bulk films, while zone drawing cause a significant alpha to beta transition in PVDF/MWCNT. Results indicate that MWCNTs act as nucleation agent during crystallization and slightly increase the degree of crystallinity of PVDF/MWCNT bulk films. TGA indicates the thermal stability is improved when MWCNT concentration increases for unoriented PVDF/MWCNT film. The modulus also increases significantly when MWCNT concentration increases. The glass transition temperature measured by the peak position of tan delta from DMA does not change with MWCNT concentration, but a slightly higher glass transition can be obtained by zone drawing. (C) 2009 Wiley Periodicals, Inc. J Appl Polym Sci 115: 3238-3248, 2010

Interfacial friction damping characteristics in MWNT-filled polycarbonate composites

Sliding Behaviour of Carbon Nanothread Within a Bundle Embedded in Polymer Matrix

Influence of Inter-tube Connections on the Stress-Strain Behavior of Nanotube-Polymer Composites: Molecular Dynamics

Nanocomposites of Poly(vinylidene Fluoride) with Multiwalled Carbon Nanotubes

Interface-Dependent Mechanical Properties in MWNT-Filled Polycarbonate

Poly(methyl Methacrylate)-Decorated Single Wall Carbon Nanotube/epoxy Nanocomposites with Re-Agglomeration Networks: Rheology and Viscoelastic Damping Performance

Effects of Fiber Diameter and Tribotest Conditions on Nonlubricated Frictional Behavior of a Microsized Metal Fiber

Tribological Behavior of Multi-Walled Carbon Nanotube/Epoxy Resin Nanocomposites

Effect of Tensile Strain on Morphology and Dielectric Property in Nanotube/polymer Nanocomposites

Melt rheological properties of nylon 6/multi-walled carbon nanotube composites

Study of the effect of amino-functionalized multiwall carbon nanotubes on dry sliding wear resistance properties of carbon fiber reinforced thermoset polymers

Mechanical and Tribological behaviors of MWCNT/Polyimide Nanocomposites under Drift of Glass Transition Temperature

Tribological Behaviour of Multi-Walled Carbon Nanotubes (MWCNT) Filled Polybutylene Terephthalate (PBT) Nanocomposites

A micromechanical study of the fatigue behavior of MWCNT-modified carbon fibers/epoxy resin single filament composites subjected to cyclic loadings

Exploration Of Dielectric Constant Dependence On Evolution Of Microstructure In Nanotube/Ferroelectric Polymer Nanocomposites

Enhancement of Friction between Carbon Nanotubes: An Efficient Strategy to Strengthen Fibers

Static and dynamic mechanical properties of polydimethylsiloxane/carbon nanotube nanocomposites

Tribological Behavior of Poly(tetrafluoroethylene) and Its Composites Reinforced by Carbon Nanotubes and Graphene Sheets: Molecular Dynamics Simulation

Toughness Enhancement of Poly(methyl methacrylate) (PMMA)/Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) Nanocomposites by Multiwall Carbon Nanotubes (MWNT)

Molecular dynamics for optimizing interfacial properties of carbon fiber-reinforced polycarbonate: molecular conformation

Effects of carbon nanotube length on interfacial properties of carbon fiber reinforced thermoplastic composites