Abstract:Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.

Study on Cotton Stalk Pulling Force Measuring Device

Experimental Study on the Vibration Parameters of Mulberry Picking

Discrete element modeling and experimental study of biomechanical properties of cotton stalks in machine-harvested film-stalk mixtures

Design Research on Roller of New Fiber Carding Machine

The Optimized Design of the On-line Monitoring Elastic Element for Measuring Axial Forces of the Rotating Machine

PARAMETRIC CALIBRATION OF COTTON STRAW PARAMETERS IN XINJIANG BASED ON DISCRETE ELEMENTS

Design and Application of the Dynamic Detection Platform for Testing the Micromechanical Properties of Agricultural Products

Optimization of cutting position and mode for cabbage harvesting

Design and Application of Dynamic Detection Platform with Microstructure Visual Observation Function for Micro-mechanical Properties of Agricultural Products

Research On Mechanics Properties Of Crop Stalks: A Review

Mechanistic analysis and experimental study of a shear-type low-loss fresh corn ear-picking mechanism

Study the Parametric Effect of Pulling Pattern on Cherry Tomato Harvesting Using RSM-BBD Techniques

Design of Cotton Recovery Device and Operation Parameters Optimization

RESEARCH ON COMB BRUSH HARVESTER AND DAMAGE MECHANISM TO MATERIAL. A REVIEW

Research on Mechanical Properties of Corn Stalk

Design and Experiment on Gripping Delivery Mechanism for Vertical-rollers Type of Corn Harvester

DESIGN AND EXPERIMENT OF TRANSVERSE AXIAL FLOW CORN FLEXIBLE THRESHING DEVICE

Bending mechanics test and parameters calibration of ramie stalks

Design of a Force Sensor for Measuring the Tearing Force of Geotextiles

Experimental Research on Influence of Pre-pressing Force and Separating Velocity and Relative Humidity on Pull-off Force

Design of Portable Fruit Picking Device