Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Ab Initio Calculations of Elastic Constants and Thermodynamic Properties of Nial under High Pressures

Ab Initio Calculation of Structure and Thermodynamic Properties of Zintl Aluminide SrAl2

First-Principle Calculations of Elastic Properties of Wurtzite-Type Aluminum Nitride under Pressure

The first-principles calculations for the elastic properties of Zr2Al under compression

First-principles Study of Ni-Al Intermetallic Compounds under Various Temperature and Pressure

First-Principle Calculations for Elastic and Thermodynamic Properties of Diamond

Ab Initio Calculation of Lattice Dynamics and Thermodynamic Properties of Beryllium

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

The Structural, Elastic, Electronic Properties And Debye Temperature Of D0(22)-Ni3v Under Pressure From First-Principles

Ab initio calculations of elastic constants and thermodynamic properties of Li2O for high temperatures and pressures

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Molecular Dynamics Study of the Melting Curve of Niti Alloy under Pressure

The Mechanical and Thermodynamic Properties of Heusler Compounds Ni2xal (X = Sc, Ti, V) under Pressure and Temperature: A First-Principles Study

Theoretical investigation of the elastic, electronic, thermodynamic and optical properties of the zinc-blende structure AlN under high pressure

Study of the Mechanical and Thermodynamic Properties on NiAl and Ni3Al

First-principles Study of Mechanical Properties and Electronic Structures of the Nickel-molybdenum Binary Compounds Under Pressure

Physical properties and Debye temperature of Al7Cu2Fe alloy under various pressures analyzed by first-principles

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

Theoretical study of the elastic and thermodynamic properties of Pt$_{3}$Al with the L1$_{2}$ structure under high pressure

High Pressure Structural And Elastic Properties Of Nio Up To 67 Gpa

First-Principles Equation of State and Phase Stability for the Ni-Al System under High Pressures