Abstract:Additive technologies enable the flexible production through scalable layer-by-layer fabrication of simple to intricate geometries. The existing 3D-printing technologies that use powders are often slow with controlling parameters that are difficult to optimize, restricted product sizes, and are relatively expensive (in terms of feedstock and processing). This paper presents the development of an alternative approach consisting of a CAD/CAM + combined wire arc additive-manufacturing (WAAM) hybrid process utilizing the robotic MIG-based weld surfacing and milling of the AlSi5 aluminum alloy, which achieves sustainably high productivity via structural alloys. The feasibility of this hybrid approach was analyzed on a representative turbine blade piece. SprutCAM suite was utilized to identify the hybrid-manufacturing parameters and virtually simulate the processes. This research provides comprehensive experimental data on the optimization of cold metal transfer (CMT)–WAAM parameters such as the welding speed, current/voltage, wire feed rate, wall thickness, torch inclination angle (shift/tilt comparison), and deposit height. The multi-axes tool orientation and robotic milling strategies, i.e., (a) the side surface from rotational one-way bottom-up and (b) the top surface in a rectangular orientation, were tested in virtual CAM environments and then adopted during the prototype fabrication to minimize the total fabrication time. The effect of several machining parameters and robotic stiffness (during WAAM + milling) were also investigated. The mean deviation for the test piece's tolerance between the virtual processing and experimental fabrication was −0.76 mm (approx.) at a standard deviation of 0.22 mm assessed by 3D scanning. The surface roughness definition Sa in the final WAAM pass corresponds to 36 μm, which was lowered to 14.3 μm after milling, thus demonstrating a 55% improvement through the robotic comminution. The tensile testing at 0° and 90° orientations reported fracture strengths of 159 and 161.3 MPa, respectively, while the yield stress and reduced longitudinal (0°) elongations implied marginally better toughness along the WAAM deposition axes. The process sustainability factors of hybrid production were compared with Selective Laser Melting (SLM) in terms of the part size freedom, processing costs, and fabrication time with respect to tight design tolerances. The results deduced that this alternative hybrid-processing approach enables an economically viable, resource/energy feasible, and time-efficient method for the production of complex parts in contrast to the conventional additive technologies, i.e., SLM.

Design and Fabrication of a Hybrid Surface‐pressure Airfoil Model Based on Rapid Prototyping

Electrothermal Response Optimization of Nozzle Structure for Multi-Material Rapid Prototyping Based on Fuzzy Adaptive Control

An Analytical Model for Pressure Distribution in Automated Fiber Placement on Irregular Surfaces and Its Application in Aeronautical Manufacturing

Low Observable Uncrewed Aerial Vehicle Wind Tunnel Model Design, Manufacturing, and Aerodynamic Characterization

A Designable Surface Via the Micro-Molding Process

Hybrid Aerodynamic Optimization of a Propeller Based on the Reformulated Blade Element Momentum Theory

Surface topology modification using 3D printing techniques to enhance the interfacial bonding strength between polymer substrates and prepreg carbon fibre-reinforced polymers

A Parametric Design Method for Hybrid Airfoils for Icing Wind Tunnel Test

Structural Design of a Large-Scale 3D-Printed High-Altitude Propeller: Methodology and Experimental Validation

Structural Optimization of a Large-Scale 3D-Printed High-Altitude Propeller Blade with Experimental Validation

Electrochemical polishing assisted selective laser melting of biomimetic superhydrophobic metallic parts

Numerical and Experimental Investigation of Molten Metal Droplet Deposition Applied to Rapid Prototyping

Fabrication of Flapping Wing Mechanism Using Various Polymer Based 3D Printing Techniques and Aerodynamic Performance Evaluation

A Rapid Method of Integrated Aeropropulsive Analysis for the Conceptual Design of Airbreathing Hypersonic Aircraft

Reliable method of aerodynamic analysis using computational fluid dynamics and scaled models in the development process of a Very Light Airplane

Abrasive flow finishing of 3D-Printed Aerofoils: Design, numerical Simulation, and experimental analysis

Biomimetic papilla texture by femtosecond laser for high-strength CFRTP/A6061-T6 FSSW hybrid structures

Sustainable Hybrid Manufacturing of AlSi5 Alloy Turbine Blade Prototype by Robotic Direct Energy Layered Deposition and Subsequent Milling: An Alternative to Selective Laser Melting?

Study on Rapid Casting for Complex Parts

Integral Airfoil Generation of Multi-rotor Aircraft Based on Optimization of Upper Wing Contour and CFD Simulation

Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests