Abstract:Interpenetrating phase composites (IPCs) with porous metal materials as the matrix and polymer materials as the reinforcement, which have a broad application prospect, have both the high strength of metal materials and the high energy absorption capacity of polymer materials. Entangled metallic wire materials are a new type of porous material with damping characteristics, which is an excellent choice for use as the matrix of IPCs. In the present work, a novel entangled metallic wire material–silicone rubber IPC is developed through the vacuum infiltration method with the entangled wire material as the matrix and silicone rubber as the reinforcing element. The mechanical properties (loss factor and tangent modulus) of the as-synthesized composites are characterized through compression tests. More specifically, the effects of key experimental parameters (strain) and material properties (matrix density, wire diameter, and anisotropy) on the mechanical properties of the composites are analyzed in detail. It is found that with the introduction of interfacial friction, the loss factor of the composites becomes higher than those of the pure entangled metallic wire material and silicone rubber; in particular, the tangent modulus is significantly enhanced. The complex structural characteristics of the proposed composite enable the loss factor and tangent modulus to exhibit a nonlinear relationship with the density over a range of displacement values. Moreover, the smaller the wire diameter is, the greater the loss factor of the composites is, while the tangent modulus exhibits the opposite trend. The unique wire contact form and preparation process endow the composites with nonlinear properties in the molding direction as well as pronounced anisotropy characteristics. A novel interpenetrating phase composite is proposed. The composite quasistatic curve is nonlinear with excellent mechanical properties. The improved energy consumption properties are due to the interfacial friction. The increase in wire density greatly improves the elastic modulus of the composite. The composite is anisotropic with a better bearing capacity in the molding direction.

Fabrication and properties of Si/Al interpenetrating phase composites for electronic packaging

Investigation of Electrical and Thermal Properties of Epoxy Resin/Silicon Carbide Whisker Composites for Electronic Packaging Materials

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Advancements in SiC-Reinforced Metal Matrix Composites for High-Performance Electronic Packaging: A Review of Thermo-Mechanical Properties and Future Trends

Enhanced mechanical and thermal properties in 3D printed Al 2 O 3 lattice/ epoxy interpenetrating phase composites

Reinforcement of thermally-conductive SiC/Al composite with 3D-interpenetrated network structure by various SiC foam ceramic skeletons

Latest research progress of SiCp/Al composite for electronic packaging

Microstructure characterization and fracture behaviors of Silicon carbide/metallic glass composites with interpenetrating architecture

Enhanced Thermal Conductivity and Microwave Dielectric Properties by Mesostructural Design of Multiphase Nanocomposite

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Construction of novel plate-shaped 4H–SiC network skeleton for enhancing 3D-interpenetrated network structure SiC/Al composites

Scanning thermal microscopy evaluation of interface thermal property of composites for electronic packaging

Tailoring the thermophysical properties of porous SiC framework reinforced Al-Mg-Si composites by Si alloying content for thermal energy management

Mechanical behavior of entangled metallic wire mesh–silicone rubber interpenetrating phase composites under quasistatic compression

Interface structure and properties of spray-forming (SiCp+β-LiAlSiO4)/6092Al matrix composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Recent Advancement in the Development of Silicon‐based Phase Change Materials

Multi-directional freeze-casting of interpenetrating phase composites with multi-aligned structure, nearly isotropy, high performance

Microstructures, thermal and mechanical properties of Al–Si-CNT composites for thermal management applications

High damping capacity of AlSi10Mg-NiTi lattice structure interpenetrating phase composites prepared by additive manufacturing and pressureless infiltration

Effect of polymer infiltration and pyrolysis (PIP) on microstructure and properties of high volume fraction SiC/Al composites prepared by a novel hybrid additive manufacturing