Abstract:A series of polyamide 1010 (PA1010 or nylon 1010) and multiwalled carbon nanotubes (MWNTs) composites were prepared by in situ polymerization of carboxylic acid-functionalized MWNTs (MWNT–COOH) and nylon monomer salts. Mechanical tensile tests and dynamic mechanical analysis (DMA) show that the Young modulus increases as the content of the nanotubes increases. Compared with pure PA1010, the Young's modulus and the storage modulus of MWNTs/PA1010 in situ composites are significantly improved by ca. 87.3% and 197% (at 0°C), respectively, when the content of MWNTs is 30.0wt%. The elongation at break of MWNTs/PA1010 composites decreases with increasing proportion of MWNTs. For the composites containing 1.0wt% MWNTs, the Young modulus increases by ca. 27.4%, while the elongation at break only decreases by ca. 5.4% as compared with pure PA1010 prepared under the same experimental conditions. Compared with mechanical blending of MWNTs with pure PA1010, the in situ-prepared composites exhibit a much higher Young's modulus, indicating that the in situ polycondensation method improves mechanical strength of nanocomposites. Scanning electron microscopy (SEM) imaging showed that MWNTs on the fractured surfaces of the composites are uniformly dispersed and exhibit strong interfacial adhesion with the polymer matrix. Moreover, unique crystallization and melting behaviors for MWNTs/PA1010 in situ composites are observed using a combination of differential scanning calorimetry (DSC) and X-ray diffraction methods. It was shown that only the α-form crystals are observed in our MWNTs/PA1010 in situ composites. This result is quite different from PA1010/montmorillonite and PA6-clay composites, where both of α- and γ-form crystals were found.

Preparation and properties of polyarylene ether nitrites/multi-walled carbon nanotubes composites

Preparation of Isotactic Polypropylene-Grafted Multiwalled Carbon Nanotubes (Ipp-G-mwnts) by Macroradical Addition in Solution and the Properties of Ipp-G-Mwnts/Ipp Composites

Nanocomposites of Poly(vinylidene Fluoride) with Multiwalled Carbon Nanotubes

Hindered phenol grafted carbon nanotubes for enhanced thermal oxidative stability of polyethylene

Preparation and characterization of polyurethane/multiwalled carbon nanotube composites

Preparation and Characterization of Polyurethane/Multi-Walled Carbon Nanotubes Composites with Multi Functional Performance

Preparation and Properties of the Polyimide/multi-Walled Carbon Nanotubes (mwnts) Nanocomposites

In Situ Polymerization Approach to Multiwalled Carbon Nanotubes Reinforced Polyundecanoylamide Composites

The Study on the Microstructures and High Performances of Melt Blending Polyurethane/Multiwalled Carbon Nanotubes Composites

Synthesis and properties of the amino-functionalized multiple-walled carbon nanotubes/polyimide nanocomposites

Synthesis and Properties of Novel Polyurethane−Urea/Multiwalled Carbon Nanotube Composites

Fabrication and Characterization of Soluble Multi‐Walled Carbon Nanotubes Reinforced P(MMA‐co‐EMA) Composites

Poly(p-phenylene terephthalamide)/carbon nanotube composite membrane: Preparation via polyanion solution method and mechanical property enhancement

Preparation and Characterization of Novel Polyethylene/carbon Nanotubes Nanocomposites with Core–shell Structure

Preparation and Electrical Properties of Multiwalled Carbon Nanotubes Filled High-density Polyethylene Composites

Study of Structure and Property of PBT/Carbon Nano-tubes Composite

Synthesis and Characterization of Multi-Walled Carbon Nanotube/Polythiophene Composites

Preparation and Performance of MWNTs/ Epoxy Resins Composites

Fabrication and Characterization of PMMA/MWCNTs Composite Materials

In Situ Polymerization Approach to Multiwalled Carbon Nanotubes-Reinforced Nylon 1010 Composites: Mechanical Properties and Crystallization Behavior

Fabrication and characterization of microwave cured high-density polyethylene/carbon nanotube and polypropylene/carbon nanotube composites