Abstract:Introduction This study create a dental composite by hybirding polyhedral oligo-sesquioxide nano monomers and bioactive glass BG 45S5. Methods Make a experimental composite resin material with a 60% filler content overall by substituting 20% of the filler with BG 45S5. The experimental resins are grouped and named P0, P2, P4, P6 and P8 based on the reactive nanomonomer methacrylic acid-based multifaceted oligomeric sesquisiloxane (POSS) added by 2%–8% in the resin matrix portion of each group. Utilize universal testing machine to analyze and compare the mechanical properties of these, then performed Fourier infrared spectrum analysis, double bond conversion analysis, and scanning electron microscope analysis. Based on this, after soaking the experimental materials artificial saliva solution or the lactic acid solution for a while, the pH changes of the solution, the release of Ca 2+ and PO 4 3− ions, and the precipitation of apatite on the resin material's surface were tested and analyzed. Cell viability tests were used to assess sample cell viability and quantify the cytotoxicity of biological cells. The independent sample t test was used to examine the group comparisons, and a difference was considered statistically significant when P <0.05. Results Outstanding mechanical and the double bond conversion are demonstrated by the nanocomposites when the POSS concentration hits 4wt%. Agglomeration will cause the performance to deteriorate if the concentration beyond this threshold. In the P4 group, the double bond conversion, CS, and FS rose by a large margin, respectively, in comparison to the blank control group P0. Thankfully, the data demonstrate that adding POSS increases adhesive ability when compared to the blank group P0, however, there is no discernible difference between the other experimental groups. The acid neutralization capacity of the P4 group is essentially the same as that of the control group (P0). Ca 2+ and PO 4 3− ions are released in significant amounts following treatment with lactic acid solution, although this tendency is clearly less pronounced in artificial saliva. SEM and EDX data indicate that when the experimental resin is soaked to a lactic acid solution and artificial saliva, apatite precipitation will happen on its surface. The results of the cell viability test indicated that there was no statistically significant difference between the experimental groups, and the viability of the cells increased after 24 and 48 hours. Conclusions POSS was included into the composite resin along with 20% bioactive glass as a filler. When the proportion of POSS is less than 4%, the indices of composite resin materials rise in a dose-dependent way. When this value is surpassed, performance begins to deteriorate. The inclusion of POSS has no influence on the biological activity of the composites, which means that the hybrid composite resin is capable of acid neutralization, ion release, and apatite precipitation. Clinical Significance The experimental composite resin can be used as an intelligent material in clinical treatment. It has the clinical application potential of preventing demineralization of tooth hard tissue, promoting remineralization and improving edge sealing through apatite precipitation.

Development of Novel Dental Nanocomposites Reinforced with Polyhedral Oligomeric Silsesquioxane (POSS)

Development of Novel Low Shrinkage Dental Nanocomposite

Mechanical Properties of Dental Nanocomposites Reinforced with Polyhedral Oligomeric Silsesquioxane(POSS)

POSS Dental Nanocomposite Resin: Synthesis, Shrinkage, Double Bond Conversion, Hardness, and Resistance Properties.

Study Of Poss On The Properties Of Novel Inorganic Dental Composite Resin

Molecular Dynamics Simulation of A Novel Kind of Polymer Composite Incorporated with Polyhedral Oligomeric Silsesquioxane (Poss)

PROPERTIES OF METHACRYL POLYHEDRAL OLIGOMERIC SILSESQUIOXANE (POSS-MA) DOPED METHACRYLATE-BASED DENTAL RESINS AND COMPOSITES CONTAINING GLASS FLAKE/Ba-Al-SiO2 GLASS POWDER AS INORGANIC DENTAL FILLERS

Effect of Nano SiO 2 Particles on the Morphology and Mechanical Properties of POSS Nanocomposite Dental Resins

Characterization of dental light-curing resin composites incorporating multiple modified low-shrink monomers

Study on the Polymerization Shrinkage and Mechanical-Physical Properties of Dental Resin Composite Modified by Polyurethane Dimechacrylate and Glass Flake Fillers

Polyhedral oligomeric silsesquioxane (POSS)-Modified thermoplastic and thermosetting nanocomposites: A review

Preparation and Characterization of Novel Polydimethylsiloxane Composites Used POSS As Cross-Linker and Fumed Silica As Reinforcing Filler

Preparation and properties of POSS/PMMA nanocomposites

Preparation and characterization of POSS‐SiO2/cyanate ester composites with high performance

Design of Resin Composites with Enhanced Physical–mechanical Properties

Preparation of low shrinkage stress dental composite with synthesized dimethacrylate oligomers.

POSS hybrid bioactive glass dental composite resin materials: synthesis and analysis

POSS and SSQ Materials in Dental Applications: Recent Advances and Future Outlooks

Effect of polyhedral oligomeric silsesquioxane on water sorption and surface property of Bis-GMA/TEGDMa composites

Synthesis of a novel monomer “DDTU-IDI” for the development of low-shrinkage dental resin composites

Polyhedral Oligomeric Silsesquioxane (POSS)-Containing Polymer Nanocomposites