Abstract:To develop a high-precision constitutive model and hot processing map for 5A06 aluminum alloy , the hot deformation behavior of the alloy was investigated through isothermal compression experiments and microstructure analysis experiments, which were conducted at temperatures ranging from 573 K to 773 K and at strain rates ranging from 0.01 to 10 s −1 . Firstly, a new constitutive model, which is based on the partial derivatives of the experimental flow data and does not significantly increase the material parameters, was proposed. Secondly, a comparison and analysis of the predictive accuracies of both the new model and the classic model were conducted. Finally, the new constitutive model was used to construct the hot processing maps of the 5A06 aluminum alloy, and the optimal hot processing parameters were validated through metallographic experiments. The results show that a high-precision constitutive model can be constructed with a small number of material parameters by considering the second-order approximation between logarithmic stress and temperature, as well as the third-order approximation between logarithmic stress and logarithmic strain rate. The mean square errors of the new model were significantly lower than those of the Arrhenius model and Hense-Spittle model for all strain rates and temperatures. There were significant differences in the prediction accuracy of the AH and HS models at different temperatures and strain rates, indicating their accuracy was dependent on temperature and strain rate. The coefficients of the new model were significantly higher than those of the AH and HS models. Moreover, the proximity of predicted values to experimental values was ranked in descending order as follows: new model, AH model, and HS model. The energy dissipation rate is relatively high when the strain rate is lower than 10 s-1 and the temperature is higher than 623 K. The instability factor is larger than zero for all conditions except when the strain rate is equal to 10 s −1 . The optimal hot working temperature range for 5A06 aluminum alloy is 623–700 K, and the strain rate should be in the range of 0.01 s −1 to 1 s −1 . The microstructure analysis matches the predicted results from hot processing maps, which can guide the hot working process of 5A06 aluminum alloy.

Analysis of Constitutive Behaviours and Processing Map of 7020 Aluminium Alloy

Modified constitutive model and workability of 7055 aluminium alloy in hot plastic compression

Hot deformation characteristics and processing maps of AA7075-H18 alloy sheet under hot forming process conditions

A new constitutive model and hot processing map of 5A06 aluminum alloy based on high-temperature rheological behavior and higher-order gradients

Research on Processing Maps of 5083 and 7020 Wrought Aluminum Alloy

Analysis of hot Formability of Al-4.6Mg-0.6Mn Alloy (AA5083)

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

Hot deformation characteristics and processing parameter optimization of 2219 Al alloy using constitutive equation and processing map

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Constitutive modeling of deformation in high temperature of a forging 6005A aluminum alloy

Hot Working Property Study of 7055 Aluminum Alloy Based on Hot Shear-Compression Deformation

A New, Precise Constitutive Model and Thermal Processing Map Based on the Hot Deformation Behavior of 2219 Aluminum Alloy

Microstructural and constitutive relationship in process modeling of hot working: The case of a 60Mg-30Pb-9.2Al-0.8B magnesium alloy

Study of Hot Deformation Behavior of 6082 Aluminum Alloy

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Constitutive equation and hot processing maps of Al–5Ti–1B master alloy

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Constitutive Equation and Hot Processing Map of Mg-16Al Magnesium Alloy Bars

The Study on Forming Property at High Temperature and Processing Map of 2219 Aluminum Alloy

Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions