Abstract:Low-Ni and Ni-free varieties of duplex stainless steels (DSSs) have been successfully developed for the first time on laboratory scale in SAIL. The alloy compositions for Ni-free and low-Ni (<1.5 wt%) DSSs were evolved through formulation of appropriate chromium and nickel equivalents to achieve an optimum phase balance of 55 vol% austenite and 45 vol% ferrite in stainless steel microstructures. Laboratory heats were made achieving target chemistries and cast into 100 mm square cross-sectioned ingots. The ingots were subsequently soaked at 1150 °C for 3 hrs for thermal/ compositional homogenization and hot rolled in number of passes to 6 and 16 mm strips in Hillé experimental rolling mill with finish rolling temperatures of 950-980 °C. The hot rolled strips were eventually conferred solution annealing treatment by soaking them at 1060 °C for 2 hours followed by rapid quenching in water to prevent precipitation of deleterious intermetallic compounds (IMCs) and secondary phases. The new steels revealed an exceptional combination of properties: higher yield strength (488 MPa for low-Ni DSS and 501 MPa for Ni-free DSS), higher tensile strength (664 MPa for low-Ni DSS and 677 MPa for Ni-free DSS) and superior Charpy V-notch impact toughness (230 and 129 Joules at room temperature and -20°C, respectively, for low-Ni DSS as against 80 and 52 Joules at similar temperatures for Ni-free DSS). The yield strength of the steels was assessed to be about 1.6-1.8 times that of conventional austenitic grades AISI 304 L and AISI 316 L in annealed condition. The low-Ni and Ni-free DSS showed remarkable corrosion resistance and have been found to exhibit passivity, corrosion rates as low as 0.08-0.11 mpy, pitting potentials in the range of 482-596 mV and charge transfer resistances of the order of 10 6 W.cm 2 in highly corrosive environment of 3.5% NaCl. The steels have been thus found to be superior in pitting/ localized corrosion resistance to AISI 304 L with pitting potential of 437 mV and comparable in performance with AISI 316 L with its high pitting potential of 602 mV. Even in the strongly reducing environment of 0.1 N H 2 SO 4 , the new steels have revealed tendency to passive film formation, breakdown potentials of 1127-1153 mV and passive film impedances of 10 4 W.cm 2 , comparable to the standard austenitic grades AISI 304 L and AISI 316 L. In boiling MgCl 2 solutions, the low Ni DSS has been found to resist stress corrosion cracking (SCC) up to 24 h; the time for crack initiation being intermediate to that for AISI 304 L (3 h) and AISI 316 L (32 h). The Ni-free DSS, on the other hand, was found to exhibit no signs of SCC failure even after 72 h of exposure to the test solution. The degree of sensitization (DoS) for both low Ni and Ni-free DSSs has been quantified to be £ 0.05 in 0.5 M H 2 SO 4 + 0.01 M KSCN, which has revealed their insusceptibility to intergranular corrosion (IGC). The steels have been found to be free from deleterious intermetallic phases such as sigma (s), chi (c), etc. and this has been ascertained from corrosion rates of <10 mdd in ferric chloride corrosion testing as per ASTM A 923 Method C.

STATUS ON PRODUCTION AND RESEARCH OF LEAN DUPLEX STAINLESS STEEL

Development of Lean Duplex Stainless Steels (LDSS) with Superior Mechanical and Corrosion Properties on Laboratory Scale

Development of Chinese duplex stainless steel in recent years

MICROSTRUCTURE EVOLUTION OF LEAN DUPLEX STAINLESS STEEL 2101 DURING HOT DEFORMATION

New Economical 19Cr Duplex Stainless Steels

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

22Cr High-Mn-N Low-Ni Economical Duplex Stainless Steels

Additive manufacturing of duplex stainless steels - A critical review

水下激光填丝直接能量沉积法制备贫双相不锈钢2101 的组织和织构演变

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

Research and development of steel for ultra-light automotive

Investigation of Selective Corrosion Resistance of Aged Lean Duplex Stainless Steel 2101 by Non-Destructive Electrochemical Techniques

A New Resource-Saving, High Manganese and Nitrogen Super Duplex Stainless Steel 25Cr–2ni–3mo–xmn–n

In Situ Observation of Surface Electrochemical Activities of Lean Duplex Stainless Steel LDX 2101

Microstructure Evolution and Mechanical Properties of Lean Duplex Stainless Steel Bars Prepared by a Short Process

The Effect of W and Cu on the Microstructure and Properties of Ni-saving 25cr Duplex Stainless Steels

Control of the Composition and Morphology of Non-Metallic Inclusions in Superduplex Stainless Steel

Maintaining Excellent Mechanical Properties via Additive Manufacturing of Low-N 25Cr-Type Duplex Stainless Steel

Numerical Simulation and Process Optimization of Laser Surface Treatment on Duplex Stainless Steel

Dynamic and localized microelectrochemical approaches to evaluate the corrosion resistance of newly developed lean duplex stainless steel alloys

Study on the Composition Design, Microstructure, Wear and Corrosion Resistant of Duplex Stainless Steels Based on Machine Learning