Abstract:Abstract Melt blending using a twin-screw extruder was used to prepare composites of polypropylene (PP)/organic rectorite (PR). The organic rectorite (OREC) was modified with dodecyl benzyl dimethyl ammonium bromide (1227). Wide-angle X-ray diffraction (WAXD) and transmission electron microscopy were used to investigate the dispersion of OREC in the composites. The d spacings of OREC in PR composites was greater than in OREC itself. The dispersion of OREC particles in the PP polymer matrix was fine and uniform when the clay content was small (2 wt.%). The rheology was characterized using a capillary rheometer. The processing behaviour of the PR system improved as the amount of OREC added increased. Non-isothermal crystallization kinetics were analysed using differential scanning calorimetry. It was shown that the addition of OREC had a heterogeneous nucleation effect on PP, and can accelerate the crystallization. However, only when fine dispersion was achieved, and at lower rates of temperature decrease, was the crystallinity greater. Wide-angle X-ray diffraction and polarized light microscopy were used to observe the crystalline form and crystallite size. The PP in the PR composites exhibited an α-monoclinic crystal form, as in pure PP, and in both cases a spherulite structure was observed. However, the smaller spherulite size in the PR systems indicated that addition of OREC can reduce the crystal size significantly, which might improve the ‘toughness’ of the PP. The mechanical properties (tensile and impact strength) improved when the amount of OREC added was appropriate. Dynamic mechanical analysis showed that the storage modulus (E’) and loss modulus (E’’) of the nanocomposites were somewhat greater than those of pure PP when an appropriate amount of OREC was added. Finally, thermogravimetric analysis showed that the PR systems exhibited a greater thermal stability than was seen with pure PP.

Latest Research Development of Polypropylene/Inorganic Nanocomposites

Progress in Nanocomposites of Polylactic Acid

PROGRESS IN MODIFICATION STUDY OF POLYPROPYLENE WITH NANOMATERIALS

Research Progress in Polyamide 6/Polypropylene/nano-Montmorillonite Composites

PREPARATION AND PROPERTIES OF INTERCALATED RECTORITE/POLYPROPYLENE NANOCOMPOSITES

Structure and Properties of Polypropylene/organic Rectorite Nanocomposites

Polypropylene/Combinational Inorganic Filler Micro-/Nanocomposites: Synergistic Effects of Micro-/Nanoscale Combinational Inorganic Fillers on Their Mechanical Properties

Research Development of Preparation and Characterization of Polypropylene/Carbon Nano-tube Composites

Tensile Performance Improvement of Low Nanoparticles Filled-Polypropylene Composites

Effect of Nanoparticles on Fibril Formation and Mechanical Performance of Olefinic Block Copolymer (obc)/polypropylene (pp) Microfibrillar Composites

Study of Modified Polymer Filled with Inorganic Nanoparticles

Network structural hardening of polypropylene matrix using hybrid of 0D, 1D and 2D carbon-ceramic nanoparticles with enhanced mechanical and thermomechanical properties

Interfacial enhancement of nano-SiO2/polypropylene composites

Research Progress in the Toughening and Strengthening of Polypropylene Via Inorganic Rigid Particles

Recent Progress in Toughening Polypropylene

Modification of Polypropylene with Composite Nucleating Agents Containing 2,2-Methylene-bis-(4, 6-di-t-butylphenylene) Phosphate/Attapulgite/Silica Nano-particles

Effects of nano-SiO_2 on reinforcing and toughening polypropylene

Toughening and strengthening of micro-and nano-SiO2/PP composites

Performance Improvement of Nano-Silica/polypropylene Composites Through In-Situ Cross-Linking Approach

Effect of Wet Surface Treated Nano-Sio2 on Mechanical Properties of Polypropylene Composite

Polypropylene/montmorillonite nanocomposites I. Preparation, characterizsation and dynamic mechnical properties