A Varied Step Control Method of MPPT for Photovoltaic System Based on AVR Microcontroller

WAN Jun,HU Chang-sheng

DOI: https://doi.org/10.3969/j.issn.1001-2257.2008.04.006

2008-01-01

Abstract:The method of 0.618 is a effective novel varied step optimization.It can track MPP changes rapidly.ATmega8 was proposed to reduce the power oscillation around MPP.

What problem does this paper attempt to address?

A Concise Control Method Based on Spatial-Domain d/d Calculation for MPPT/Power Reserved of PV Systems

Jiahua Ni,Ji Xiang

DOI: https://doi.org/10.1109/TEC.2022.3195565

IF: 4.8767

2023-01-01

IEEE Transactions on Energy Conversion

Abstract:The idea of perturbation and observation has been widely applied in PV power regulation strategies. However, the conventional Perturb and Observe (P&O) algorithm has an optimal trade-off in choosing efficient step size to balance steady-state oscillations and dynamic response. Modified P&O algorithms improve the performances but increase the computational complexity. This paper develops a concise PV control method taking dp/dv as a control variable calculated in the spatial-domain. The spatial-domain dp/dv calculation is based on the current moment data and the spatially adjacent data to avoids zero denominator problem. This control method achieves oscillations-free in steady-state and has a fast dynamic tracking speed with high-frequency control signal updating. Moreover, it unifies both MPPT (dp/dv = 0) and power reserved modes (dp/dv < 0). The simulation test system with different scenarios is established to highlight its benefits. Also, experiments on a micro-boost converter combined with a PV panel in the practical set-up are carried out to verify its effectiveness. Performance of an spatial-domain dp/dv calculation based control method is compared with the popular and recent state-of-the-art methods. The satisfactory dynamic and steady-state performances show the superiority over state-of-the-art methods.
An Analog Integrated MPPT Controller Designed for DMPPT Solar Array

Ru-Cheng Jiang,Yan Han,Lu Jie

DOI: https://doi.org/10.1109/icsict.2016.7999085

2016-01-01

Abstract:An analog MPPT controller suitable for DMPPT solar array is presented in this paper. In order to achieve an accurate tracking, “Perturb and Observe” tracking algorithm is applied. PWM+ burst dual mode control strategy is adopted in the controller to obtain a high efficiency in both high and low irradiation intensity. Finally, simulation results and experimental results are reported and discussed. It shows that in DMPPT topology the output power is 15% more than that in CMPPT topology.
An Analog Mppt Controller Ic Together With Its Application Circuit

Fang Liu,Yan Han,Yue Gao,Jun Sun

DOI: https://doi.org/10.1587/elex.11.20140880

2014-01-01

IEICE Electronics Express

Abstract:An analog integrated maximum power point tracking (MPPT) controller which is suitable for distributed MPPT (DMPPT) topology is presented in this paper. Without large numbers of external circuit components, the DC/DC converter together with its MPPT controller can be made small enough to be integrated into the junction box, which is practical and cost effective for DMPPT topology. Besides a negative feedback loop is used in the proposed system to make the output voltage of PV panel less susceptible to fluctuations of irradiation intensity and interference of switching noise. Meanwhile, an improved P&O algorithm is adopted to achieve a fast and precise tracking especially in fast changing weather conditions. Furthermore, the tracking precision is higher than 99.5% under different external environmental conditions.
Spatial-domain dP/dV calculation based photovoltaic control method

NI Jia-hua,XIANG Ji,ZHAO Bo

DOI: https://doi.org/10.3785/j.issn.1008-973X.2023.07.020

2023-01-01

Abstract:A novel approach was proposed to address the zero-denominator issue encountered in the current step calculation of dP/dV in order to eliminate steady-state oscillations in the output of photovoltaic (PV) system based on the perturbation and observation (P&O) method. dP/dV was calculated based on data from adjacent points in space, eliminating perturbation observation. The dP/dV value was directly used as the control variable. The zero-denominator issue was circumvented in the steady state, ensuring zero oscillation. The high-frequency signal updating feedback guaranteed a swift dynamic tracking process during dynamic states. The maximum power point tracking mode (dP/dV = 0) and the power standby mode (dP/dV < 0) were unified, achieving excellent output performance under various dP/dV reference values. Both Matlab/Simulink simulations and physical experiments were conducted. The superiority of the proposed algorithm in terms of maximum power tracking performance was demonstrated by comparing with traditional P&O algorithms and the latest MPPT algorithms. Further comparison with control methods based on time-domain dP/dV calculation showed the advantage of the proposed algorithm in power standby output performance.
An Improved Variable Step Size Photovoltaic MPPT Algorithm Based on Perturb and Observe Method

Mukui Yin,Linlin Qin,Gang Wu,Chun Shi

DOI: https://doi.org/10.1117/12.2628665

2022-01-01

Abstract:Maximum power point tracking (MPPT) technology can significantly improve and optimize the power generation efficiency in solar photovoltaic power generation system. The perturb and observe method is one of the most common MPPT application methods. This paper introduces an improved variable step size MPPT algorithm which has three adjustable degrees of freedom. A buck circuit simulation model is built and simulation results show that the algorithm improves tracking speed and steady-state performance.
An Analog MPPT Controller Without Multiplier for PV Applications Based on Simplified P&O Method

Chenxi Wang,Min Chen,Xinghua Zhang,Mingzhi Gao

DOI: https://doi.org/10.1109/ecce.2017.8096446

2017-01-01

Abstract:This paper proposed an analog controller without multiplier to realize the Maximum Power Point Tracking (MPPT) for PV applications based on an improved perturbation and observation (P&O) method. Comparing with traditional analog MPPT controller designs which need a multiplier to calculate the power value to implement P&O, the proposed method only perturbs and observes single variable to get the same effects, therefore the circuit is simplified and the cost is decreased. The controller uses classical and simple functions of electronic circuits. This design is applicable for most PV applications and is easily made into an IC. The whole circuit has been implemented and validated on both simulation and hardware platforms. The results show good tracking accuracy and high efficiency of MPPT (more than 99%) under variable solar irradiation.
Research of MPPT Algorithm in Photovoltaic System Based on Variable-Step

SHEN Shidie,YAO Wei

DOI: https://doi.org/10.3969/j.issn.1005-2895.2013.05.014

2013-01-01

Abstract:Maximum power point tracking(MPPT) technology largely affects the efficiency of the photovoltaic inverter system,and the traditional fixed-step perturbation and observation method exists the contradiction between the MPPT accuracy and tracking speed.A variable-step perturbation and observation method was proposed,and the algorithm was improved.The simulation model set up in the Simulink and the MPPT was realized by changing the duty cycle of switching tube in Boost converter.The simulation results show that the improved algorithm effectively improves the MPPT accuracy and tracking speed.At last,the improved algorithm is applied on the 3kw prototype and the experimental results verify the effectiveness of the algorithm.
A Variable Voltage MPPT Control Method for Photovoltaic Generation System

Liu Liqun,Wang Zhixin

2009-01-01

Abstract:To increase the output efficiency of a photovoltaic (PV) generation system it is important to have an efficient maximum power point tracking (MPPT) technique. This paper describes the analysis, design and implementation of an efficient tracking method for a stand-alone PV generation system, which automatically adjusts the reference of output voltage to track the maximum power point (MPP) by using the expiatory program. Compared with the conventional constant voltage (CV) method, the proposed approach can effectively improve the tracking speed and accuracy simultaneously. Furthermore, an improved control system is designed for the pulse-width-modulation (PWM) inverter to achieve the objective of MPPT. Theoretical analysis and principle of proposed method are presented and simulation results are given to verify the validity of control method.
Rapid Variable-step MPPT of Photovoltaic Cell Based on Virtual Load

Lin Wang,Dongxu Dai,Peng Li,Yanchao Ji

DOI: https://doi.org/10.3969/j.issn.1000-3886.2017.06.014

2018-01-01

Abstract:Traditional MPPT for photovoltaic systems involves selection of step and cycle,and the variable step algorithm depends on system parameters and other conditions,thus affecting system tracking response speed and stability.To further accelerate the search of the maximum power point and reduce steady-state power output oscillation,this paper presented a novel fast variable-step search algorithm,which,by defining a virtual load line and with help of directional tracking of the maximum power point realized through the I-V curve,can lock the working point to the proximity of the maximum power point in several operating cycles.Then,in the steady state,by defining the allowable error,we can achieve an output power without oscillation in the steady state.Experimental results show that the proposed algorithm can raise the search speed significantly,ensure output stability,and adapt itself to rapid changes in external environment.
A General Algorithm for Flexible Active Power Control of Photovoltaic Systems

Hossein Dehghani Tafti,Ariya Sangwongwanich,Yongheng Yang,Georgios Konstantinou,Josep Pou,Frede Blaabjerg

DOI: https://doi.org/10.1109/apec.2018.8341156

2018-01-01

Abstract:The maximum power point tracking (MPPT) is generally implemented in grid-connected photovoltaic (PV) power plants to maximize the energy yield. However, as the penetration level increases, challenging issues such as overloading and overvoltage arise in PV applications. Accordingly, a constant power generation (CPG) operation, in which the PV output power is limited to a specific value, has been imposed by some grid regulators to alleviate the integration challenges. In that case, the combined operation of MPPT and CPG is required, which increases the complexity of the controller design. To generalize the two control objectives, a flexible active power control algorithm that combines both MPPT and CPG operating modes is proposed. The proposed algorithm can optimize the performance in both modes (i.e., MPPT and CPG). By adjusting the voltage-step between two consecutive operating points, fast dynamics and low-power oscillations can be obtained. The performance of the proposed strategy is evaluated through simulations and experiments under different irradiance and power reference profiles.
A Variable Step Sizes Perturb and Observe MPPT Method in PV System based on Flyback Converter

Haodong Feng,Yuqing Chen,Xinye Ma

DOI: https://doi.org/10.1109/cac53003.2021.9727299

2021-10-22

Abstract:Aiming to track the maximum power point of photovoltaic power generation, a variety of strategies are proposed. The P&O method is a general and available policy, but traditional P&O strategy cannot track MPP quickly, accurately and stably. A variable step sizes P&O method is proposed to optimize the traditional P&O method. The background and working principle of MPPT and Flyback converter are introduced. The traditional P&O approach is critically considered, and a new variable step sizes P&O approach is presented. The simulation is carried out by Matlab/Simulink, and some curve results are obtained. The results of different sizes of steps and irradiation environments are analyzed. The results present that the variable step sizes P&O strategy could obtain MPP faster at lower oscillation rate at steady-state, and increase the efficiency and output of the renewable power generation based on solar photovoltaic.
Improved variable-step incremental conductance MPPT algorithm applied to photovoltaic storage systems

Rui Ji,Zhihe Wang

DOI: https://doi.org/10.1088/1742-6596/2427/1/012045

2023-02-22

Journal of Physics: Conference Series

Abstract:For the traditional PV maximum power tracking control method in terms of tracking speed and stability, proposed an improved variable-step incremental conductance method. The method first speeds up the tracking speed by the constant voltage coefficient method to quickly locate around the MPP(Maximum power point,MPP) and dynamically adjusts the step size using the inverse tangent function value when the operating point is located to the left of the maximum power point, and dynamically adjusts the step size using the exponential function value when the operating point is located to the right. Given the characteristics of photovoltaic power generation, it usually constitutes a light storage system with an energy storage battery. To verify the effectiveness, the simulation experiments are carried out in Matlab/Simulink to build a photovoltaic energy storage system model, which contains an energy storage battery. Results indicate that the proposed new method achieves the optimization of tracking precision and speed according to the nature of the function and can make the energy storage battery charge and discharge stably, which verifies the practicality of the proposed improved algorithm.
A high performance MPPT control method

Lei Ma,Yaojie Sun,Yandan Lin,Zhifeng Bai,Liqin Tong,Jieqiong Song

DOI: https://doi.org/10.1109/ICMREE.2011.5930794

2011-01-01

Abstract:This paper presents the analysis, design and implementation of a high-performance step-up Maximum power point tracking (MPPT) system for grid-connected Photovoltaic (PV) generation. The high-achieved MPPT control method, which is an important essential part of the efficient and low-cost PV system, needs to solve two main problems: wrongly tracking the local maxima under partial shading, and tracking in the direction opposite to reality under rapid atmospheric changes. Furthermore, the MPPT strategy should have the following traits: practical, ability to reach the global maxima in a minimum of time, costless and high efficiency. A simple boost topology using radiometer and a voltage sensor is proposed with the MPPT algorithm and the operation characteristics are analyzed. © 2011 IEEE.
A Boost Converter‐based MPPT Steady‐state Oscillation‐free Fast Tracking Control Strategy for Photovoltaic Power Systems

Ning Li,Changjie Zhang,Deng Wei,Ming Liu,Yan Zhang

DOI: https://doi.org/10.1049/pel2.12400

IF: 2

2022-01-01

IET Power Electronics

Abstract:With the conventional perturbation and observation (P&O) method, photovoltaic (PV) converters have long maximum power point (MPP) tracking times and three-point oscillations at the steady state that can lead to output power losses and inefficiencies in grid connections. To overcome these drawbacks, a fast tracking and steady-state-oscillation-free control strategy is proposed. The strategy first stores four random duty cycle values on the basis of the duty cycle variation characteristics of the PV panel power adjustment, then calculates the odd and even duty cycle difference and judges the steady state by varying the duty cycle difference threshold. The strategy next obtains the MPP duty cycle using a median filtering algorithm (MFA) to suppress the steady-state oscillation and improves the tracking speed by resetting the appropriate duty cycle step according to the slope of the PV curve of the PV panel output and the corresponding adaptive coefficients. The proposed algorithm was simulated and experimentally validated under various irradiance conditions, and the results show that the algorithm can improve the PV panel output efficiency compared to both the conventional P&O and the adaptive P&O methods.
A Variable Step Size P&O MPPT Algorithm for Three-Phase Grid-Connected PV Systems

Duan Jiandong,Xiang Ma,Song Tuo

DOI: https://doi.org/10.1109/ciced.2018.8592040

2018-01-01

Abstract:The main objective of this paper is to propose a variable step size Perturb and Observe (P&O) maximum power point tracking (MPPT) algorithm for two-stage three-phase grid-connected photovoltaic (PV) systems. The previous-stage Boost circuit achieves the maximum power point tracking control. The inverter side of the rear-stage realizes the stability of the DC bus voltage and the control of the grid-connected current. By adopting a novel variable-step size P&O algorithm, a fixed step size is adopted when the distance is far from the maximum power point, and the step size is reduced by half every time the working point crosses the peak point, until the final step is smaller than the set threshold and the operating point is stable at the maximum power point. The proposed method effectively solves the problem of slow tracking speed and voltage disturbance near the power point in the conventional fixed-step P&O. In the inverter side, the use of double closed-loop control can ensure the stability of the DC bus voltage and achieve unit power factor grid-connected control. Finally, the proposed algorithm is applied to the two-phase three-phase grid-connected simulation model established in MATLAB. The simulation results show that the proposed method shortens the tracking time by 0.08s and eliminates the power oscillation phenomenon near the maximum power point compared to the fixed step P&O.
Modified Asymmetrical Variable Step Size Incremental Conductance Maximum Power Point Tracking Method for Photovoltaic Systems

Yong Tian,Bizhong Xia,Zhihui Xu,Wei Sun

DOI: https://doi.org/10.6113/jpe.2014.14.1.156

IF: 0.913

2014-01-01

Journal of Power Electronics

Abstract:The power?voltage (P?V) characteristic of a photovoltaic (PV) array is nonlinear and time varying with the change in atmospheric conditions. As a result, the maximum power point tracking (MPPT) technique must be applied in PV systems to maximize the generated energy. The incremental conductance (INC) algorithm, one of the MPPT strategies, is widely used for its high tracking accuracy, good adaptability to rapidly changing atmospheric conditions, and easy implementation. This paper presents a modified asymmetrical variable step size INC MPPT method that is based on the asymmetrical feature of the P?V curve. Compared with conventional fixed or variable step size method, the proposed method can effectively improve tracking accuracy and speed. The theoretical foundation and design principle of the proposed approach are validated by the simulation and experimental results.
A One-Step Mppt Method Based On 5-Parameter Model Of Pv Panel

Jierong Miao,Da Xie,Ruixiang Fan

2017-01-01

Abstract:Traditionally, MPPT methods are independent of the mathematical model and require multi-step adjusting of the inverter, resulting in multiple disturbances of the PV system. Actually the photovoltaic cell has a definite U-I curve at a certain degree of illuminance and temperature, which can be described in a mathematical model. This paper proposes a one-step MPPT method based on 5-parameter model. Utilizing voltage and current measurements, The DC/DC inverter of each PV panel obtains equations for five parameters and solves them via Newton iteration method. According to P-U curve, the derivative of P to U is zero. Thus an implicit equation of the maximum power can be given along with a constraint. Considering the bimodal characteristics of P-U curve under cloud shade condition, the constraint prevents the result to converge to the low peak point. Then the DC/DC inverter can adjust the PV system to MPP by one step. Furthermore, since the five parameters vary at different illuminance and temperature, the database can be established based on the correspondence between condition and parameters, which can give back to DC/DC inverter to improve the tracking efficiency.
Simple Moving Voltage Average Incremental Conductance MPPT Technique with Direct Control Method under Nonuniform Solar Irradiance Conditions

Amjad Ali,Wuhua Li,Xiangning He

DOI: https://doi.org/10.1155/2015/479178

2015-01-01

International Journal of Photoenergy

Abstract:A new simple moving voltage average (SMVA) technique with fixed step direct control incremental conductance method is introduced to reduce solar photovoltaic voltage (VPV) oscillation under nonuniform solar irradiation conditions. To evaluate and validate the performance of the proposed SMVA method in comparison with the conventional fixed step direct control incremental conductance method under extreme conditions, different scenarios were simulated. Simulation results show that in most cases SMVA gives better results with more stability as compared to traditional fixed step direct control INC with faster tracking system along with reduction in sustained oscillations and possesses fast steady state response and robustness. The steady state oscillations are almost eliminated because of extremely small dP/dV around maximum power (MP), which verify that the proposed method is suitable for standalone PV system under extreme weather conditions not only in terms of bus voltage stability but also in overall system efficiency.
Research on MPPT Technology Based on Three-Stage Variable Step Size Disturbance Observation Method

Tao Hai,Yongjian Chen,Yu Shi,Junjie Li,Zhenyu Liu

DOI: https://doi.org/10.1088/1742-6596/1650/2/022107

2020-01-01

Journal of Physics Conference Series

Abstract:Abstract For the traditional disturbance observation method, it is impossible to take into account both tracking speed and steady-state accuracy with a fixed step size, so we change the step size and propose disturbance observation method based on three-stage variable step size. The specific method is to set the basic step size and the slope threshold of the P-V curve, and then scale factors according to the interval segment of the slope value of the working point, so as to realize the dynamic adjustment of the step size. Simulation experiments show that after the algorithm is improved, the tracking speed is faster when the environment changes suddenly; when the environment is stable, the power oscillation is reduced. The above has certain positive significance for improving efficiency of the photovoltaic system.
Mppt Techniques for Photovoltaic Applications

Mohamed A. Eltawil,Zhengming Zhao

DOI: https://doi.org/10.1016/j.rser.2013.05.022

2013-01-01

Abstract:The photovoltaic (PV) system is one of the renewable energies that attract the attention of researchers in the recent decades. The PV generators exhibit nonlinear I-V and P-V characteristics. The maximum power produced varies with both irradiance and temperature. Since the conversion efficiency of PV arrays is very low, it requires maximum power point tracking (MPPT) control techniques. The maximum power point tracking (MPPT) is the automatic control algorithm to adjust the power interfaces and achieve the greatest possible power harvest, during moment to moment variations of light level, shading, temperature, and photovoltaic module characteristics. The purpose of the MPPT is to adjust the solar operating voltage close to the MPP under changing atmospheric conditions. It has become an essential component to evaluate the design performance of PV power systems. This investigation aims to assess different MPPT techniques, provide background knowledge, implementation topology, grid interconnection of PV and solar microinverter requirements presented in the literature, doing depth comparisons between them with a brief discussion. The MPPT merits, demerits and classification, which can be used as a reference for future research related to optimizing the solar power generation, are also discussed. Conventional methods are easy to implement but they suffer from oscillations at MPP and tracking speed is less due to fixed perturb step. Intelligent methods are efficient; oscillations are lesser at MPP in steady state and tracked quickly in comparison to conventional methods. (C) 2013 Elsevier Ltd. All rights reserved.

A Varied Step Control Method of MPPT for Photovoltaic System Based on AVR Microcontroller

A Concise Control Method Based on Spatial-Domain d/d Calculation for MPPT/Power Reserved of PV Systems

An Analog Integrated MPPT Controller Designed for DMPPT Solar Array

An Analog Mppt Controller Ic Together With Its Application Circuit

Spatial-domain dP/dV calculation based photovoltaic control method

An Improved Variable Step Size Photovoltaic MPPT Algorithm Based on Perturb and Observe Method

An Analog MPPT Controller Without Multiplier for PV Applications Based on Simplified P&O Method

Research of MPPT Algorithm in Photovoltaic System Based on Variable-Step

A Variable Voltage MPPT Control Method for Photovoltaic Generation System

Rapid Variable-step MPPT of Photovoltaic Cell Based on Virtual Load

A General Algorithm for Flexible Active Power Control of Photovoltaic Systems

A Variable Step Sizes Perturb and Observe MPPT Method in PV System based on Flyback Converter

Improved variable-step incremental conductance MPPT algorithm applied to photovoltaic storage systems

A high performance MPPT control method

A Boost Converter‐based MPPT Steady‐state Oscillation‐free Fast Tracking Control Strategy for Photovoltaic Power Systems

A Variable Step Size P&O MPPT Algorithm for Three-Phase Grid-Connected PV Systems

Modified Asymmetrical Variable Step Size Incremental Conductance Maximum Power Point Tracking Method for Photovoltaic Systems

A One-Step Mppt Method Based On 5-Parameter Model Of Pv Panel

Simple Moving Voltage Average Incremental Conductance MPPT Technique with Direct Control Method under Nonuniform Solar Irradiance Conditions

Research on MPPT Technology Based on Three-Stage Variable Step Size Disturbance Observation Method

Mppt Techniques for Photovoltaic Applications