Pump Matching Engine Power Accord to Various Work Condition Control of Hydraulic Excavator

李武,崔毅,潘国远

DOI: https://doi.org/10.3969/j.issn.1672-545X.2008.08.004

2008-01-01

Abstract:The division of state control hydraulic excavator pump-matching engine power,the division of state control on the principle of energy conservation,energy conservation and work to achieve speed of both the pump-matching engine programme.

What problem does this paper attempt to address?

Control Strategy of Power Matching and Power Sources Optimization for Hydraulic Excavators

Dongyun Wang,Cheng Guan,Shuangxia Pan,Xiao Lin

2009-01-01

Abstract:Because of the sharp fluctuation of the load condition, the working points of the engine are mostly distributed in the high fuel consumption area. This causes low fuel economy of the power source and is the main reason of high power losses in conventional hydraulic excavators. In order to solve this problem, a new control strategy based on hybrid technology was presented. Its target was to achieve power matching and optimize the working condition of the power sources simultaneously. Experimental results show that the control strategy can realize the target. It reduce the speed fluctuation and optimize the working points of the engine. Meanwhile, it achieves higher fuel economy than conventional methods.
Engine Speed Control Method of Parallel Hydraulic Hybrid Excavator

来晓靓,管成,肖扬,仲光旭

DOI: https://doi.org/10.6041/j.issn.1000-1298.2014.01.003

2014-01-01

Abstract:By analysis on the principle and structure of the parallel hydraulic hybrid excavator, an improved hydraulic hybrid scheme was proposed which uses a two-way hydraulic motor to replace the hydraulic secondary regulation pump and controls the assistant power loop by switching valve in different states. After modeling the new system with Simulink software, the parameters of the components and control method were determined. The double speed points control strategy was test on the improved parallel hydraulic hybrid excavator. The engine speed and the output torque of the assistant hydraulic power system were adjusted by an engine speed PID control method integrated with the load forecasting. The simulation and experiment results showed that the control method could effectively improve the engine speed fluctuation in the hydraulic hybrid system, and make the speed stable near the target speed, so energy-saving increases by 14%.
Simulation Research of Parallel Hydraulic Hybrid Excavator

Zhang Minjie,Wang Qingjiu,Guan Cheng

2010-01-01

Abstract:Due to the power transmission structures of the traditional excavators, the relevant methods can not help the distribution of working points of the engine. So a hydraulic hybrid technology and its control scheme was proposed herein. The working conditions were analyzed and the structures of hydraulic hybrid excavator were introduced. A parallel hydraulic hybrid system was chosen for simulation. The load of an actual excavator was used as input of the system. The parallel hydraulic hybrid excavator demonstrates that it can stabilize the engine speed, increase the efficiency and optimize the drivability.
Dynamic Characteristic of Power Source in Parallel Hybrid Hydraulic Excavator

林潇,管成,潘双夏,王冬云

DOI: https://doi.org/10.3785/j.issn.1008-973x.2010.02.026

2010-01-01

Abstract:The working condition property of the hydraulic excavator was analyzed based on the 15 second typical operating cycle.The mathematical model of power source in parallel hybrid hydraulic excavator was established.An optimal set of power source parameters in parallel hybrid hydraulic excavator was pro-posed.Then the generator/motor efficiencies of the space vector pulse width modulation(SVPWM)-con-trolled permanent magnet synchronous motor(PMSM)and the charge/discharge efficiencies of the NiMH battery were analyzed under the same circumstance as well as the dynamic response characteristic including motor speed,motor torque and battery SOC.Simulation results show that the optimal set of power source in powertrain can satisfy the requirement of power and energy transformation efficiency for hydraulic exca-vator,and help achieve better fuel consumption with hybrid configuration.Furthermore the battery system was only treated as a media to transform energy.The more energy-saving and higher efficient control for the hydraulic excavator was achieved.
Power Matching Method of Parallel Hybrid Excavator

WANG Dong-yun,PAN Shuang-xia,LIN Xiao,GUAN Cheng

DOI: https://doi.org/10.3785/j.issn.1008-973x.2009.10.007

2009-01-01

Abstract:The currently used control strategy of hybrid excavator does not consider the power matching between the power sources, so it is hard to guarantee the control effect. Based on the analysis of hydraulic excavator working condition and the development of a parallel hybrid excavator model, the concepts of hybridization, optimum hybridization and dynamic optimum hybridization were introduced, and the matching degree between the main power source and the auxiliary one was described. The influences of hybridization factor(HF) on the control strategy, fuel economy and drivability were investigated. A new method to decide the HF which is based on the load of the excavator and aims to improve the fuel economy was presented . The simulation shows that the method can get a suitable HF which can guarantee the control effect without the limitation of the power sources, and it can get the best fuel economy without sacreficing the drivability of the hydraulic excavator.
Research on Modeling and Control Strategy of Parallel Hybrid Power System in Excavator

Tuo Fu-xing,GUAN Cheng,XU Zhen

DOI: https://doi.org/10.3969/j.issn.1002-2333.2010.04.011

2010-01-01

Abstract:According to the parallel hybrid hydraulic excavator power system, a dynamic model of entire system including batteries, motor/generator and diesel engine was built. The transient dynamic model of four-cylinder diesel engine was built emphatically, which could reflect engine speed and torque response to the load accurately. For further energy saving of hydraulic excavator, a multi-work-point control strategy was developed based on the dynamic model and the load, which aimed at optimizing the engine work points and improving the fuel efficiency. Simulation results indicate that the engine model is reasonable and effective, and the control strategy can achieve higher fuel efficiency.
A Parameter Matching Method of the Parallel Hydraulic Hybrid Excavator Optimized with Genetic Algorithm

Xiaoliang Lai,Cheng Guan

DOI: https://doi.org/10.1155/2013/765027

IF: 1.43

2013-01-01

Mathematical Problems in Engineering

Abstract:This paper proposed a parameter matching method based on the energy storage unit, the accumulator in the parallel hydraulic hybrid excavator (PHHE). The working condition, system structure, and control strategy of the excavator were all considered. It took the 20-ton series PHHE as the example and displayed the parameter matching course of the main components: engine, accumulator, and hydraulic secondary regulatory pump. Their installed powers were reduced after the matching course. Furthermore, the parameters of the PHHE system were optimized with the genetic algorithm to get the most suitable values for system initialization. By analyzing the simulation results, it could be concluded that the parameter matching method had an impressive improvement of the energy saving under the same working condition and brought obscure influence to the mechanism dynamics.
Energy saving scheme of hydraulic excavators based on hybrid power technology

Dong-yun WANG,Shuang-xia PAN,Xiao LIN,Cheng GUAN

2009-01-01

Abstract:To further improve fuel efficiency of hydraulic excavators, a new energy saving scheme which used the hybrid power source to replace the conventional single diesel engine was proposed. By analyzing the load condition of the hydraulic excavators and the distribution of the engine working point, the necessity and feasibility of hybrid technology for hydraulic excavators were revealed. Matlab/Simulink models of the two kinds of hybrid excavators were constructed which used the load data collected from a real 5 t excavator as the load input. The energy saving effect, system cost and power performance of the three kinds of power train systems were compared through simulation and experiments. Comparison results showed that the parallel configuration was the most suitable technology for hydraulic excavators energy saving. It could improve energy saving for hydraulic excavators.
Research on the Design and Control Strategy for a Flow-Coupling-based Hydraulic Hybrid Excavator

Yang Xiao,Cheng Guan,Xiaoliang Lai

DOI: https://doi.org/10.1177/0954407013502326

2014-01-01

Abstract:This paper presents a hybridization structure for the flow coupling of a hydraulic hybrid excavator. Multiple energy regeneration systems are used as the energy source for the hydraulic hybrid excavator. The flow-coupling structure is designed on the basis of practical working conditions and then integrated into a 23 ton excavator as the experimental platform to facilitate power system design and control studies. The initial constant-hybrid-ratio control is first examined using a simulation model to obtain the control performances of the main power source and the assistant power source, and the problems are then analysed to derive a two-step optimization. Prototype experiments demonstrate the effectiveness and feasibility of the flow-coupling-based hybridization structure of the hydraulic hybrid excavator. Test results indicate that flow coupling with an optimal control strategy results in an improved control performance and energy efficiency and can eventually increase the overall energy- saving effect to 10.1%.
Control Strategy of Hybrid Excavator Based on Condition Recognition and Hybridization Optimization

Wang Dongyun,Guan Cheng

2010-01-01

Abstract:The hybrid technology brought new opportunity to energy saving of a hydraulic excavator. However, the control strategy is hard to be determined because of the complexity of working condition and cyclic fluctuation of the load. As the dynamic-work-point control strategy can not optimize the main power source and the auxiliary one simultaneously, a new control strategy based on condition recognition and hybridization optimization was presented. It optimized the power distribution rate between the two power sources according to the load condition and the SOC (state of charge) of the battery. Experimental results show that the control strategy ameliorates the speed fluctuation of the engine, optimizes the working points of the engine and SOC of battery. Ultimately it improves the fuel economy of the hybrid hydraulic excavator.
Energy-Saving Trajectory Tracking Control of a Multi-Pump Multi-Actuator Hydraulic System.

Ruikai Bao,Qingfeng Wang,Tao Wang

DOI: https://doi.org/10.1109/access.2020.3027354

IF: 3.9

2020-01-01

IEEE Access

Abstract:With the increasing application of automated hydraulic excavators, the demand for high-level control performance and significant energy saving schemes becomes stronger. The traditional hydraulic excavators with single-pump power source have amounts of coupling loss on throttling valves due to multi-actuator effect. Moreover, their operability is usually influenced by the load varying in a large range. This paper proposes a multi-pump system with on-off valve matrix to eliminate the coupling loss by dividing the system into several single-pump single-actuator subsystems. A pump/valve coordinate control strategy with multiple working modes is developed to adapt the load variation. First, mathematical modeling including mechanical part and hydraulic part is carried out based on dynamic analysis. Second, a three-level coordinated control scheme is proposed: 1) The motion tracking level utilizes backstepping control technique with load observation to obtain the desired hydraulic force; 2) The working mode switching level configures the pump and valve control mode to maximize energy saving according to load condition; 3) The force control level utilizes control technique to guarantee the stability and dynamic performance. Finally, comparative experimental results are presented to show the good control performance and significant energy saving achieved by the proposed multi-pump multi-actuator system as well as the control strategy.
Efficiency Analysis and Evaluation of Energy-Saving Pressure-Compensated Circuit for Hybrid Hydraulic Excavator

Tao Wang,Qingfeng Wang

DOI: https://doi.org/10.1016/j.autcon.2014.07.012

IF: 10.3

2014-01-01

Automation in Construction

Abstract:A hydraulic cylinder driven scheme combining a pressure compensator and an energy recovery device together has been proposed to achieve good control operation and energy-saving capability simultaneously. In this paper, its efficiency characteristics are further investigated in order to provide analytical and experimental references to practical applications. Since an excavator owns multiple actuators, a general schematic configuration including hydraulic cylinders with and without energy recovery is developed and analyzed. Based on the analysis of energy losses in every conversion, component selections and possible improvements are discussed, and then the design flowchart and criteria of key parameters are also presented. Finally, experiments under different load and velocity conditions are implemented on a test bench. Energy distributions, recovery efficiencies and component efficiencies are all evaluated.
Parameters Matching Method for Parallel Hybrid Hydraulic Excavators

Xiao Lin,Cheng Guan,Shuangxia Pan,Dongyun Wang

2009-01-01

Abstract:In order to optimize the efficiency of a parallel hybrid hydraulic excavator (PHHE), this paper firstly get started with the analysis of the system's structure, and then the optimal objective function and constraint equations that depict powertrain unit and energy storage unit for PHHE were put forward along with a parameter matching method for the machine. For the purpose of component sizing and matching in PHHE, one case was done in a 5 ton hybrid excavator, and the system with the designed parameters of components could reduce components' peak power, increase system efficiency and decrease fuel consumption rate by using Matlab and Simulink toolbox.
Design of New Hydraulic Pumping Unit with Electro-hydraulic Proportional Control

魏新,孙军,周华,徐兵

DOI: https://doi.org/10.3969/j.issn.1001-3881.2009.02.012

2009-01-01

Abstract:A new design scheme of hydraulic pumping unit was brought forward to meet the requirements of long-stroke and low-frequency in the process of oil extraction.By adopting the new compound cylinder and combining the technology of electro-hydraulic proportional control and hydraulic counterweight,the unit appears to be more compact and applicative,meets the demands of long-stroke,low-frequency and large-load,and makes stroke and frequency fully-variable.
Design and Control of Hydraulic Hybrid System for Excavators

Shizhen Li,Jianhua Wei,Jinhui Fang,Kai Guo,Wei Liu

DOI: https://doi.org/10.1115/fpmc2015-9564

2016-01-01

Abstract:This paper is to study on a novel recovery and release hydraulic hybrid system for excavators (HHE). The HHE uses hydraulic accumulators to recover the potential energy of the boom, the kinetic energy of the swing motor and the overflow hydraulic energy of the excavator’s main relief. The recovered energy is then utilized through a variable hydraulic motor as assistant power of the engine. The key issue of the HHE is that the operation of the boom must be similar to the conventional one about the sensing of the driver and the system must achieve higher efficiency and save more energy when comparing with the conventional system. In order to improve the recovery efficiency and while controlling the boom velocity with the similar operation, one design concept named “microcut” is proposed. When the boom drops down fast, a proportional valve is used to control the boom. While the boom goes down slowly, the recovery system is cut off. Then, the multi-way valve of the original system works to ensure good handling. An experimental prototype is designed and built in a 21-tons excavator. A 16% fuel-saving effect is obtained by weighing engine’s fuel consumption with the same amount of work, under conditions of the similar operation and higher efficiency compared with the conventional excavator.
Study on Dynamic Performance of EFMC System in Hydraulic Excavator

Wang Xiangbing,Tong Shuiguang,Ge Junxu,Zhang Jian

DOI: https://doi.org/10.3969/j.issn.1004-132x.2014.15.009

2014-01-01

Abstract:A virtual prototype of EFMC system in hydraulic excavator was constructed by analy-zing the control principle of EFMC system based on lastdruck unabh?ngige durch-fluss verteilung (LUDV)multi-way valve,the accuracy of flow matching was improved by adopting feedback closed-loop control method with real-time detection of oil cylinder speed signals.The dynamic and hydraulic models of EFMC system in hydraulic excavator were constructed respectively,and the co-simulation was conducted based on actual working conditions,the dynamic characteristics and energy-saving char-acteristics of mining operation process were studied,compared the experimental results with the tradi-tional LUDV load-sensing system,the results indicate that compared with the load-sensing system,the dynamic response characteristics and stability performance of the EFMC system are improved,and the pressure margin is reduced obviously,the energy efficiency is improved,also the dynamic response characteristics of feedback closed-loop control system are improved.Theoretical basis and reference are provided for further research on dynamic characteristics,energy-saving characteristics and stability performance in excavator.
Simulation Evaluation on Power-saving Effectiveness of Multi-pump Drive System for Combined Power Hydraulic Excavators

张彦廷,雷西娟,王庆丰,肖清

DOI: https://doi.org/10.3969/j.issn.1000-1212.2008.02.017

2008-01-01

Abstract:Power-saving and emission problems of hydraulic excavators have been widely concerned in the industry due to their large usage volume, high fuel consumption and high emission. In order to reduce fuel consumption and increase emission quality of the excavators, power-saving measures such as combined power technology and multi-pumps, multi-circuits drive are introduced on the basis of existing conventional hydraulic excavator system and various power-saving schemes are designed. With MATLAB system, simulation model of basic machine is established on every scheme; then the engine fuel consumption, equipped power and some key parameters are simulated and calculated in a standard excavating cycle. The research results show that, adopting combined power drive, the fuel engine can work in high efficiency area to make fuel fully burned so fuel usage ratio is increased and emission is decreased. But, only with combined power drive, power-saving effect is not obvious due to high power consumption from so many power converting links; while multi-pump, multi-circuit system can effectively reduce pressure compensation loss of hydraulic system to increase work efficiency of hydraulic system; so the two schemes are combined to get better power-saving result and emission quality. Further research shows that a three pump drive scheme adopting parallel combined power technology and electric motor drive rotation will obtain a better power-saving effect.
Characteristic Analysis of Electro-hydraulic Flow Matching Control System in Hydraulic Excavator

YANG Huayong,LIU Wei,XU Bing,ZHU Xiaojun

DOI: https://doi.org/10.3901/jme.2012.14.156

2012-01-01

Journal of Mechanical Engineering

Abstract:The electro-hydraulic flow matching control system with the electro-proportional valve and electro-proportional pump works in a synchronous control mode of the valve and pump.It eliminates the hysteresis between the pump and valve in the traditional load-sensing systems nearly.Closed-loop feedback control of pressure and preset pressure margin between pump and maximum load pressure are not needed.It reflects the combination of flexibility and efficiency of hydraulic systems,improving energy efficiency and control performance.The experimental prototype of 2-ton excavator with the electro-hydraulic flow control system is taken as the investigation subject.Energy consumption and dynamic characteristic are comparatively analyzed between the traditional load sensing hydraulic system and the electro-hydraulic flow matching hydraulic system.The controller with flow share capabilities is designed for electro-hydraulic flow matching control.Compared with the traditional load-sensing system,the electro-hydraulic flow matching hydraulic system has the same as with post compensation with anti saturation.The pressure margin is reduced by more than 0.6-0.7 MPa,and the energy consumption is decreased by 8%-10%.It can not only improve the dynamic characteristic and energy efficient,but also the system stability.
Parameter Matching Method for Hybrid Power System of Hydraulic Excavator

Qing XIAO,Qing-feng WANG

DOI: https://doi.org/10.19721/j.cnki.1001-7372.2008.01.022

2008-01-01

Abstract:In order to improve the efficiency of hybrid power system applied in hydraulic excavator, a parameter matching method was developed to optimize the power system. Structure, working condition and control strategy of the hybrid power system applied in hydraulic excavator were analyzed. Then, a parameter matching method based on optimization object functions and constraint condition functions was proposed. The parameters of the main components, such as engine, electric motor, generator and capacitor of the power system were matched using this method. The matching results were analyzed using the built hybrid power hydraulic excavator model. The results show that the system efficiency is improved significantly after parameter is matched and the main components meet the demand of working condition.
Stage-based power matching control of hydraulic excavator

Yu GAO,Peien FENG,Bei PENG,Qingying QIU

DOI: https://doi.org/10.11990/jheu.201605053

2017-01-01

Abstract:To reduce fuel consumption in hydraulic excavators, we set reasonable engine operation points according to different operation cycle stages and objects.On this basis, we propose an operation-point switching control strate-gy based on the maximum acceleration required to realize fast switching between the different engine operation points.The stability of these operation points at the same operational stage is ensured by a collaborative control strategy of torque feedback and speed feedback.To verify the feasibility of our proposed strategy, we built a test bed and conducted experiments on an actual excavator.Our experimental results demonstrate that our proposed strategy can maintain the stability of the engine operation at the best operation points, which can reduce fuel con-sumption while increasing operational efficiency.

Pump Matching Engine Power Accord to Various Work Condition Control of Hydraulic Excavator

Control Strategy of Power Matching and Power Sources Optimization for Hydraulic Excavators

Engine Speed Control Method of Parallel Hydraulic Hybrid Excavator

Simulation Research of Parallel Hydraulic Hybrid Excavator

Dynamic Characteristic of Power Source in Parallel Hybrid Hydraulic Excavator

Power Matching Method of Parallel Hybrid Excavator

Research on Modeling and Control Strategy of Parallel Hybrid Power System in Excavator

A Parameter Matching Method of the Parallel Hydraulic Hybrid Excavator Optimized with Genetic Algorithm

Energy saving scheme of hydraulic excavators based on hybrid power technology

Research on the Design and Control Strategy for a Flow-Coupling-based Hydraulic Hybrid Excavator

Control Strategy of Hybrid Excavator Based on Condition Recognition and Hybridization Optimization

Energy-Saving Trajectory Tracking Control of a Multi-Pump Multi-Actuator Hydraulic System.

Efficiency Analysis and Evaluation of Energy-Saving Pressure-Compensated Circuit for Hybrid Hydraulic Excavator

Parameters Matching Method for Parallel Hybrid Hydraulic Excavators

Design of New Hydraulic Pumping Unit with Electro-hydraulic Proportional Control

Design and Control of Hydraulic Hybrid System for Excavators

Study on Dynamic Performance of EFMC System in Hydraulic Excavator

Simulation Evaluation on Power-saving Effectiveness of Multi-pump Drive System for Combined Power Hydraulic Excavators

Characteristic Analysis of Electro-hydraulic Flow Matching Control System in Hydraulic Excavator

Parameter Matching Method for Hybrid Power System of Hydraulic Excavator

Stage-based power matching control of hydraulic excavator