Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Laboratory Investigation and Commercial Test for Rotors-Assembled Strand Applied in Smooth Tube

Heat Transfer and Friction Characteristics of Turbulent Flow Through Plain Tube Inserted with Rotor-Assembled Strands

Experimental Study of Heat Transfer Enhancement and Friction Loss Induced by Inserted Rotor-assembled Strand (II) Lubricant Oil 22

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Experimental investigation of heat transfer and friction factor in tubes fitted with regularly spaced rotor strands

Experimental Study of Single-Phase Pressure Drop and Heat Transfer in a Micro-Fin Tube

Experimental Investigation on the Friction Characteristics of Water–ethylene Glycol Mixture Flow in Internal Helical Finned Horizontal Tubes

Heat Transfer And Pressure Drop In Tubes Fitted With Grooved Lobe Rotor-Assembled Strands

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Experimental Study of Single-Phase Flow and Heat Transfer Characteristics for a Horizontal Internal Helically-Finned Tube

Experimental study on single-phase heat transfer performance of internal helically finned tubes covering low Reynolds number in turbulent flow

Numerical Study on Characteristics of Heat Transfer and Friction Factor in a Circular Tube with Central Slant Rods

Experimental Studies on Heat Transfer and Friction Factor Characteristics of Turbulent Flow Through a Circular Tube with Small Pipe Inserts

Experimental Investigation on Flow and Heat Transfer in Rough Microtube

Pressure Drop, Heat Transfer and Performance of Single-Phase Turbulent Flow in Spirally Corrugated Tubes

Experimental Result of condensation in micro-fin tubes of different geometries

Friction characteristics for water-ethylene glycol mixture flow in horizontal tubes with new type of helically fins

Convective Heat Transfer and Pressure Drop of Annular Tubes with Three Different Internal Longitudinal Fins

A Numerical Study on Thermo-Hydraulic Characteristics of Turbulent FLow in a Circular Tube Fitted with Conical Strip Inserts

Performance of single-phase turbulent flow heat transfer and frictional pressure drop in an internally ribbed tube

Experimental Study of Boiling Heat Transfer in Smooth/micro-Fin Tubes of Four Refrigerants