Abstract:Objectives: Device subsidence is a well-known complication following cervical disc arthroplasty. Its occurrence has been closely tied with the endplate-implant contact interface. But current literature on the geometry of cervical endplate is very scarce. The aim of this anatomical investigation was to analyze geometry of inferior endplates of the cervical vertebrae, thereby identifying the common endplate shape patterns and providing morphological reference values consummating the design of the implant.Patients and methods: Reformatted CT scans of 85 individuals were analyzed and endplate concave depth, endplate concave apex location, sagittal diameter of endplate, coronal concave angle, as well as transverse diameter of endplate were measured in mid-sagittal plane and specified coronal plane. According to the endplate concave apex location, the inferior endplates in mid-sagittal plane were classified into 3 types: type I with posteriorly positioned apex, type II with middle situated concave apex and type III with anteriorly positioned apex. Moreover, the inferior endplates in specified coronal plane were also classified into three types: concave, flat and irregular.Results: Based on visual assessment, for the mid-sagittal plane, type I endplate accounted for 26.9% of all the 510 endplates of 85 individuals, while the proportion of type II and type III endplates were 53.9 and 19.2% respectively. For the specified coronal plane, 68.6% of all the 510 endplates were evaluated as concave, 26.9% as flat and the remaining 4.5% as irregular. Among all measured segments, C3 had the largest endplate concave depth values in mid-sagittal plane, while C7 the least; C5 and C6 had the largest sagittal endplate diameter values, while C2 the least. For each level, the sagittal endplate concave depth and endplate diameter of females were significantly smaller than those of males (P < 0.05). Among all measured segments, C7 had the least coronal concave angle. Gender did not influence coronal concave angle significantly (P > 0.05). Increasing from C2 to C7, the endplate transverse diameters of females were significantly smaller than those of males (P < 0.05).Conclusion: The exact shape and geometry of cervical endplate are crucial for the design and improvement of cervical disc prosthesis. Gender difference of sagittal and transverse diameters of cervical endplate should be given more attention when implanting a disc prosthesis. These endplate geometrical parameters should be taken into consideration when calculating most suitable geometric parameters of new disc prosthesis. (C) 2016 Elsevier B.V. All rights reserved.

Correlation of Prodisc-C Failure Strength with Cervical Bone Mineral Content and Endplate Strength

Correlation of Cervical Endplate Strength with CT Measured Subchondral Bone Density

Endplate Concavity Variation of Lumbar Motion Segments a Finite Element Analysis

Biomechanical properties of lumbar endplates and their correlation with MRI findings of lumbar degeneration

Correlation Between Osteoporosis and Endplate Damage in Degenerative Disc Disease Patients: a Study Based on Phantom-Less Quantitative Computed Tomography and Total Endplate Scores.

A new cervical artificial disc prosthesis based on physiological curvature of end plate: a finite element analysis.

Loss of Cervical Endplate Integrity Following Minimal Surface Preparation

Predictive Value of Cervical Degenerative Quantitative Scoring System on Postoperative Disc Height Loss after Cervical Disc Replacement

Geometry of Inferior Endplates of the Cervical Spine

Biomechanical Analysis of A Novel Prosthesis Based on the Physiological Curvature of Endplate for Cervical Disc Replacement

Biomechanical Evaluation of Spinal Column after Percutaneous Cement Discoplasty: A Finite Element Analysis

Quantitative CT-based bone strength parameters for the prediction of novel spinal implant stability using resonance frequency analysis: a cadaveric study involving experimental micro-CT and clinical multislice CT

[The effect of disc degeneration on the structural property distributions in the cervical vertebral endplates]

[Biomechanical Analysis of Different ProDisc-C Arthroplasty Design Parameters after Implanted: a Numerical Sensitivity Study Based on Finite Element Method].

Quantitative Morphometric Study of the Subaxial Cervical Vertebrae End Plate

BIOMECHANICAL ANALYSIS OF DIFFERENT PRODISC-C ARTHROPLASTY DESIGNS AFTER IMPLANTATION: A NUMERICAL SENSITIVITY STUDY

CT correlation of spinal canal diameter with pedicle size for safer posterior cervical pedicle screw fixation

Quantitative Analysis of the Correlation Between Preoperative Cervical Degeneration and Postoperative Heterotopic Ossification after Cervical Disc Replacement: Minimum 10-Year Follow-Up Data.

Correlation of CT-based bone mineralization with drilling-force measurements in anatomical specimens is suitable to investigate planning of trans-pedicular spine interventions

Clinical Effectiveness of Anterior Cervical Discectomy and Fusion Using Tritanium C Anterior Cervical Cage vs. PEEK Cage

Biomechanical Comparison of a New Memory Compression Alloy Plate versus Traditional Titanium Plate for Anterior Cervical Discectomy and Fusion: A Finite Element Analysis