Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Preparation of W–Al–Mo Ternary Alloys by Mechanical Alloying

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Amorphization in the AlC System by Mechanical Alloying

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

W–Sn solid solution synthesized by mechanical alloying at room temperature

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Preparation of fine-grained MoW solid solution alloys with excellent performances

Microstructural evolution and thermal stability in a nanocrystalline lightweight TiAlV0.5CrMo refractory high-entropy alloy synthesized by mechanical alloying

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

The Effects of Yttrium on the Mechanical Alloying of AlW System

Study on mechanical alloying behavior and thermal stability of HfMoNbTaTi refractory high-entropy alloy

Alloying behavior of W and Mo in the as-cast dual-phase FeNiCrAl multi-component alloys

Influence of Tungsten Content on Microstructural Evolution of Cobalt-Containing High-Entropy Alloy via Mechanical Alloying

High-throughput exploration of alloying effects on the microstructural stability and properties of multi-component CoNi-base superalloys

Effect of Tungsten on Microstructure and Mechanical Properties of Novel NiMnCrMoWx High-Entropy Alloys Developed by Mechanical Alloying

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

Effect of Mechanical Alloying on the Microstructure and Properties of W–Ti Alloys Fabricated by Spark Plasma Sintering

Alloying behavior of binary to octonary alloys based on Cu–Ni–Al–Co–Cr–Fe–Ti–Mo during mechanical alloying

Synthesis of Ultrafine Fe-W-Al-Ti-Ni-C-B Powders by Mechanical Alloying