Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Synthesis and structural stability of Ti2GeC

Synthesis and compressive behavior of Cr2GeC up to 48GPa

Synthesis Of A New Max Compound (Cr0.5v0.5)(2)Gec And Its Compressive Behavior Up To 49 Gpa

High-Pressure Powder X-Ray Diffraction Experiments and Ab Initio Calculation of Ti3alc2

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

First-principles Study of Structural, Thermodynamic, Elastic, and Magnetic Properties of Cr2GeC under Pressure and Temperature

Ab Initio Geometry Optimization and Ground State Properties of Layered Ternary Carbides Ti3mc2 (M = Al, Si and Ge)

The structure, elastic and thermodynamic properties of Ti2GaC from first-principles calculation

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Pressure-induced Structural Transformation of CaC2.

Pressure-induced Reversible Phase Transition on Mo2Ga2C

Pressure prediction of phase stability, anisotropic elasticity, and thermodynamic properties of Ti<sub>2</sub>AC (A = Cd, In) ternary compound

High Pressure Structural Study of Β-Ti3o5: X-ray Diffraction and Raman Spectroscopy

Single-phase formation and mechanical properties of (TiZrNbTaMo)C high-entropy ceramics: First-principles prediction and experimental study

Effect of Ge on microstructure and mechanical properties of Ti3SiC2/Al2O3 composites

Thermal Equation of State of Tic: A Synchrotron X-Ray Diffraction Study

Equations of State of Co 2 TiO 4 -Sp, Co 2 TiO 4 -CM, and Co 2 TiO 4 -CT, and Their Phase Transitions: an Experimental and Theoretical Study

Experimental study of covalent Cr3C2 with high ionicity: Sound velocities, elasticity, and mechanical properties under high pressure

Pressureless manufacturing of high purity Ti3AlC2 MAX phase material: Synthesis and characterisation

Phase transformation B1 to B2 in TiC, TiN, ZrC and ZrN under pressure