Abstract:One of the important failure criteria of press operations in industry for forming simulations is the Forming Limit Diagram (FLD). The complex loading effects on FLD, in particular the localized necking phenomenon under stretch-bending condition, have not been fully investigated and well understood. In practical sheet metal applications, the deformation is invariably three dimensional with a combination of stretching and bending. For most sheet materials under these complex loading processes used in industry, strong Bauschinger effect is observed, and the material hardening behavior tends to be anisotropic. This study aims to understand and evaluate such anisotropic hardening effect on the forming limit prediction under stretch-bending condition. The extended through-thickness Marciniak–Kuczynski (M–K) analysis is incorporated with Yoshida–Uemori (YU) two-surface kinematic hardening constitutive model, which has a more accurate description of the reverse loading behavior than that of the conventional isotropic hardening model. The material parameters used in this paper for YU model are calibrated with the experimental data from uniaxial large-strain tension-compression cyclic test. Both the isotropic hardening and YU kinematic hardening models with Hill'48 yield surface are employed in the analysis for the purpose of comparison. The Forming Limit Average Stress Diagram (FLASD) under stretch-bending condition is proposed to extend the understanding of Forming Limit Stress Diagram (FLSD) from in-plane to out-of-plane deformations. The “bending-ratio-dependent” phenomenon in forming limit diagram is predicted and observed in both stress/strain space with the proposed method. It suggests that the individual stress/strain state cannot represent system behavior. Forming limits under stretch-bending is suggested as an occurrence of system instability, not individual material instability. The system behavior of sheet metal deformation is reinforced as critical to the understanding of necking instability in stretch bending processes. The analysis shows that the Bauschinger effect provides positive effect in delaying the necking instability, predicting higher formability for sheet metals under stretch-bending. The insight obtained in this paper provides further understanding of the localized necking phenomenon under stretch-bending condition.

Discussion about fracture in profile bending process

Numerical Analysis and Punching Shear Fracture Based Design of Longitudinal Plate to Concrete-Filled CHS Connections

FEM ANALYSIS ON FRACTURE TOUGHNESS OF Q460C HIGH-STRENGTH STEEL

Review on Fracture Criterion of Sheet Metal Forming

Experimental and numerical investigation of failure during bending of AA6061 aluminum alloy sheet using the modified Mohr-Coulomb fracture criterion

Sheet metal forming limits under stretch-bending with anisotropic hardening

Theoretical failure investigation for sheet metals under hybrid stretch-bending loadings

THE ANALYSIS ON STRESS STATUS NEAR THE CRACK TIP FOR THREE POINTS BENDING SPECIMEN WITH A CRACK

A New Approach To Damage Modelling And Fracture Analysis For Metal Bar With V-Shaped Notch

Theoretical and experimental investigation of the deformation shape in press-braking bending considering surface residual stresses induced by milling operation

Fracture characterization of Carbon fiber-reinforced polymer-concrete bonded interfaces under four-point bending

Fracture of dual phase sheets under uniaxial tension(Ⅱ):Nonlinear finite element analysis

Study on deformation difference between the contact zone and the non-contact zone of the flexible 3D stretch bending profile and roller dies based on pre-stretching amount

Mixed-Mode Fracture Of Hybrid Material Bonded Interfaces Under Four-Point Bending

Broad Stress Triaxiality Ratio Band Fracture Experiments in DP900 Metal Sheets and Corresponding Predictive Capability of Advanced Phenomenological and Micromechanical Fully Coupled Damage Models

Application of modified fracture criteria incorporating T-stress for various cracked specimens under mixed mode I-II loading

A ductile fracture criterion based on stress triaxiality and its application to the shearing process

Fracture prediction of NM450TP wear-resistant steel plates during air bending using a mesoscopic heterogeneous model

Model for predicting ductile fracture of SA508-3 steel undergoing hot forming

Experimental Study on Flexible Bending of Aluminum Profiles with Hyper-Elastic Pad

Study on One-Step Simulation for the Bending Process of Extruded Profiles