Abstract:The purpose of this study was to prepare ginkgolide B (GB) lyophilized powder for injection with excellent appearance and stable quality through a formulation screening and by optimizing the freeze-drying process. Cremophor EL as a solubilizer, PEG 400 as a latent solvent, and mannitol as an excipient were mixed to increase the solubility of GB in water to more than 18 times (about from 2.5 × 10−4 mol/L (0.106 mg/mL) to 1.914 mg/mL). Formulation screening was conducted by orthogonal design where the content of GB in the solution before lyophilization (using external standard method of HPLC) and reconstitution time after lyophilization were the two evaluation indexes. The optimized formulations were GB in an amount of 2 mg/mL, Cremophor EL in an amount of 16% (v/v), PEG 400 in an amount of 9% (v/v), mannitol in an amount of 8% (w/v), and the solution pH of 6.5. Through four single-factor experiments (GB adding order, preparation temperature of GB solution, adding amount, and adsorption time of activated carbon), the preparation process of GB solution was confirmed. The glass transition temperature of maximally GB freeze-concentrated solution was − 17.6°C through the electric resistance method. GB lyophilized powder began to collapse at − 14.0°C, and the fully collapsed temperature was − 13.0°C, which were determined by freeze-drying microscope. When the collapse temperature was determined, the primary drying temperature was obtained. Thereby, the freeze-drying curve of GB lyophilized powder was initially identified. The freeze-drying process was optimized by orthogonal design, the qualified product appearance and residual moisture content were the two evaluation indexes. The optimized process parameters and process were (1) shelf temperature, decreased from room temperature to − 45.0°C, at 0.5°C/min in 2 h; (2) shelf temperature increased from − 45.0 to − 25.0°C, at 0.1°C/min, maintained for 3 h, and the chamber pressure was held at 10 Pa; (3) shelf temperature was increased from − 25.0 to − 15.0°C at 0.1 °C/min, maintained for 4 h, and the chamber pressure was held at 10 Pa; and (4) shelf temperature was increased from − 15.0 to 20.0°C at 1.0 °C/min, maintained for 4 h, and the chamber pressure was raised up to 80 Pa. In these lyophilization process conditions, the products complied with relevant provisions of the lyophilized powders for injection. Meanwhile, the reproducibility was satisfactory. Post-freezing annealing had no significantly beneficial effects on shortening the freeze-drying cycle and improving the quality of GB lyophilized powder.

Preparation of Matrine and Glucose Injection

Study of the Stability of Matrine Injection in Different Conventional Infusion Fluids

Characterisation and Critical Processes Identification for Production of Herbal Preparations Using 1H-NMR and Chemometrics: A Case Study of Trichosanthis Pericarpium Injection.

Standards of Multiple Electrolytic and Invert Sugar Injection Specific Prescription Evaluation Along with Analysis of Results and Clinical Improvement

Analysis of Chemical Constituents in Shenmai Injection by LC-Q-TOF-MS and LC-IT-MS

Optimization for the Ethanol Precipitation Process of Botanical Injection: Indicator Selection and Factor Influences

Quantitative Profiling of Comprehensive Composition in Compound Herbal Injections: an NMR Approach Applied on Shenmai Injection

Systematic investigation for the stability of traditional Chinese medicine injection composition using Shenmai injection as a model

[The Effect of Preparation Method on the Quality of Shen-Mai Injection].

[Fingerprint of Shenmai Injection Based on ~1H-NMR Technique].

Optimization of membrane dispersion ethanol precipitation process with a set of temperature control improved equipment.

Preparation and Quality Control of Ascorbic Acid and Sodium Chloride Injection

Comparison of Two Separation Technologies Applied in the Manufacture of Botanical Injections: Second Ethanol Precipitation and Solvent Extraction

Simultaneous Determination of Four Alkaloids in Gan-Yan-Ling Injection by GC-MS

[Study on Balance of Process of Alcohol Precipitation of Ganmaoling Granules].

Compatibility and Stability of Dexamethasone Sodium Phosphate Combined with Sodium Aescinate in Infusion Solutions

Synthesis, characterization and evaluation of a pH-responsive molecular imprinted polymer for Matrine as an intelligent drug delivery system

Study on the prescription and production process for the dobutamine hydrochloride glucose injection

Matrine Determination and Pharmacokinetics in Human Plasma Using LC/MS/MS.

Formulation Screening and Freeze-Drying Process Optimization of Ginkgolide B Lyophilized Powder for Injection

Determination of Sophocarpine, Matrine, and Sophoridine in KUHUANG Injection by GC-MS