Abstract:An orally applicable nifedipine-loaded core tablets was coated using high viscosity grade HPMC (100,000cps) in ethanol/water cosolvent. The release of coated tablet was evaluated using USP paddle method in 900ml of simulated gastric fluid (pH 1.2) for 2h followed by intestinal fluid (pH 6.8) for 10h. The surface morphologies using scanning electron microscope and photo-images using digital camera of coated tablet during the release test were also visualized, respectively. The viscosity of hydro-alcoholic HPMC solution largely decreased as the amount of ethanol increased. There was no significant difference in viscosity among plasticizers used. The distinct and continuous coated layer was observed using scanning electron microscope. However, the surface morphologies were highly dependent on HPMC concentration and ratio of coating solvents. The higher ratio of ethanol/water gave a longer lag time prior to drug release. Lag time also increased as a function of the coating levels based on weight gains due to increased thickness of coated layer. Lag time is inversely correlated with HPMC concentration in ethanol/water (5:1) cosolvent. As the HPMC concentration slightly decreased from 3.8 to 3.2% in hydroalcoholic coating solution, a large increase of lag time was observed. As the swelling (mixing) time of high viscosity grade HPMC in ethanol/water cosolvent increased from 1 to 5h, the release rate was decreased due to enough plasticization of polymer. Based on photo-imaging analysis, the coated tablet was initially swelled and gelled without erosion and disintegration over 5h. The disintegration of the coated tablet was occurred approximately 7h after dissolution, resulting in pulsed release of drug. The high viscosity grade HPMC can be applicable for polymeric coating after careful selection of solvent systems. The release behavior and lag time could be controlled by coating conditions such as HPMC concentration, ethanol/water ratio as a coating solvent, coating level and swelling (mixing) time of coating solution. The current time-controlled release tablet coated with high viscosity grade HPMC with a designated lag time followed by a rapid release may provide an alternative to site specific or colonic delivery of drugs. In addition, the release behavior can be matched with body’s circadian rhythm pattern in chronotherapy.

Controlled poorly soluble drug release from solid self-microemulsifying formulations with high viscosity hydroxypropylmethylcellulose.

Novel Hot Melt Extruded Matrices of Hydroxypropyl Cellulose and Amorphous Felodipine–Plasticized Hydroxypropyl Methylcellulose As Controlled Release Systems

A new solid self-microemulsifying formulation prepared by spray-drying to improve the oral bioavailability of poorly water soluble drugs.

Study on Nimodipine Self-microemulsifying Drug Delivery System

Development of a HPMC-based controlled release formulation with hot melt extrusion (HME)

Development and Evaluation of High Bioavailable Sustained-Release Nimodipine Tablets Prepared with Monolithic Osmotic Pump Technology

Effects of Hydrophilic Carriers on Structural Transitions and in Vitro Properties of Solid Self-Microemulsifying Drug Delivery Systems.

Investigations on the drug releasing mechanism from an asymmetric membrane-coated capsule with an in situ formed delivery orifice

Engineering Hot-Melt Extruded Solid Dispersion for Controlled Release of Hydrophilic Drugs.

Controlled Release of Dual Drug-Loaded Hydroxypropyl Methylcellulose Matrix Tablet Using Drug-Containing Polymeric Coatings.

Modulating the nifedipine release from sustained release matrix tablets using hydrophilic polymers

Controlled Drug Release System Based on Cyclodextrin-Conjugated Poly(lactic Acid)-B-poly(ethylene Glycol) Micelles.

Preparation, Characterization, and Drug Release Behaviors of Drug Nimodipine‐loaded Poly(ε‐caprolactone)‐poly(ethylene Oxide)‐poly(ε‐caprolactone) Amphiphilic Triblock Copolymer Micelles

A Study of Microemulsions As Prolonged-Release Injectables Through In-Situ Phase Transition

Preparation, in Vivo and in Vitro Evaluation, and Pharmacodynamic Study of DMY‐Loaded Self‐Microemulsifying Drug Delivery System

A Novel Controlled Drug Delivery System Based on Alginate Hydrogel/chitosan Micelle Composites.

Development of Floating Delivery for Solid Self Micro-Emulsifying Drug Delivery System of Prochlorperazine Maleate

Release Behavior and Photo-Image of Nifedipine Tablet Coated with High Viscosity Grade Hydroxypropylmethylcellulose: Effect of Coating Conditions.

Ph-Sensitive Micelles Self-Assembled from Amphiphilic Copolymer Brush for Delivery of Poorly Water-Soluble Drugs.

Study on the preparation of carboxymethyl chitosan-coated nimodipine nanoliposomes and their in vitro release

Nifedipine solid dispersion in microparticles of ammonio methacrylate copolymer and ethylcellulose binary blend for controlled drug delivery. Effect of drug loading on release kinetics