Abstract:Particle size and content of RDX are the two main factors that affect the burning stability of RDX-based propellants. However, these effects and the corresponding mechanisms are still controversial. In this work, we investigated the physicochemical processes during burning and the corresponding mechanisms through the technologies of structure compactness analysis on the base of voidage measurement and theoretical interfacial area estimation, apparent burning rate measurement using closed vessel (CV) and extinguished burning surface characterization relying on interrupted closed vessel (ICV) and scanning electron microscope (SEM). The results indicate that the voidage increased with the increase of RDX content and particle size due to the increasing interfacial area and increasing interface gap size, respectively. The apparent burning rate increased with the increase of RDX particle size because of the decreasing RDX specific surface area on the burning surface, which could decrease the heat absorbing rates of the melting and evaporation processes of RDX in the condensed phase. Similarly, the apparent burning rate decreased with the increase of RDX content at pressures lower than around 55 MPa due to the increasing RDX specific surface area. Whereas, an opposite trend could be observed at pressures higher than around 55 MPa, which was attributed to the increasing heat feedback from the gas phase as the result of the increasing propellant energy. For propellants containing very coarse RDX particles, such as 97.8 and 199.4 μm average size, the apparent burning rate increased stably with a flat extinguished surface at pressures lower than around 30 MPa, while increased sharply above around 30 MPa with the extinguished surface becoming more and more rugged as the pressure increased. In addition, the turning degree of <em>u</em>-<em>p</em> curve increased with the increase of coarse RDX content and particle size, and could be reduced by improving the structure compactness.

Influence of Surface Coating of RDX Fillers on the Safe Properties of HTPB Propellant

Preparation and Safety of Well-Dispersed RDX Particles Coated with Cured HTPB

Preparation, High-Density Spherical, and Low Sensitivity of RDX/NC/PMMA Composite Particles

Preparation, characterization, and investigation of thermal behavior of improved HMX and RDX through coating by TNT

A new insight into the mechanical behavior of high-quality RDX in pressed polymer bonded explosives

Dynamic Mechanical Response and Damage Mechanism of HTPB Propellant under Impact Loading

Molecular dynamics simulation of bonding role of cyclic borate ester in improving mechanical properties of the HTPB propellant

Study on Dynamic Impact and Ignition Response Behavior of GAP/PET/RDX Based Propellant

Research on microscopic structure–activity relationship of AP particle–matrix interface in HTPB propellant

Chemical Modification Of Hydroxyl-Terminated Polybutadiene And Its Application In Composite Propellants

Core-Shell Structured HMX@Polydopamine Energetic Microspheres: Synergistically Enhanced Mechanical, Thermal, and Safety Performances

Technology of Ultra-fine RDX Coating with Rapid Expansion of Supercritical Solution Method

Effects of particle size and content of RDX on burning stability of RDX-based propellants

The effect of Mg(BH4)2 on the energy characteristics of RDX based aluminized explosives

Mechanical Properties and Thermal Decomposition Mechanism of Glycidyl Azide Polyol Energetic Thermoplastic Elastomer Binder with RDX Composite

Effective desensitization of composite materials HMX@PDA by insensitive DAAF: To improve safety performance

Ultrafine RDX / Al Preparation and Properties of Mixed Explosives

Poly(aluminum chloride) shell-desensitized cyclotrimethylenetrinitramine explosive core

Effect of Boron‐Aluminium Particles on Rheological Properties of AP/HTPB Based Bi‐Curative Composite Solid Propellants

Enhancing energy release of aluminized propellants and explosives through fluorinated binder

The effect of Al/oxidizers interfacial structure on the mechanical properties of composite propellants