Abstract:Research on improving the corrosion resistance of carbon steel has become a hot topic in the iron and steel field in recent years. Copper plating on the surface of carbon steel is considered an effective means to improve its corrosion resistance, but the copper-plated carbon steel material prepared by this method has the problems of poor abrasion resistance, easy delamination of copper layer and similar issues, which affect the service performance of the copper-plated carbon steel material. To solve this problem, a new type of material whose surface is copper and the copper element is gradually diffused into carbon steel was developed by a plating-diffusion method, which is defined as a copper-carbon steel gradient material. Carbon steel with a copper plated surface and the Cu-Fe/carbon steel gradient material with 80% Cu content on the surface were prepared by the same method. The cross-sectional microstructure and composition of different samples were analysed, and the corrosion behaviors of samples in 3.5% NaCl solution were studied by the linear polarization curve method and electrochemical impedance spectroscopy. The cross-sectional microstructure result shows that the diffusion of copper in carbon is mainly carried out along its grain boundary, and the diffusion of copper will inhibit the growth of grains during heat treatment. As shown in the results of corrosion behaviors, there is no pitting corrosion in the corrosion process of all samples, as well as the stable passive film. All samples showed active dissolution. Compared with carbon steel, the corrosion potential of the Cu/carbon steel gradient material becomes more positive from −600 mV to −362 mV, the corrosion current density decreases from 53.0 μA/cm2 to 30.6 μA/cm2 and the radius of electrochemical impedance spectroscopy enlarges while the corrosion resistance is improved, and the corrosion resistance is mainly obtained by its surface copper layer. The corrosion resistance of Cu-Fe/carbon steel gradient material is lower than that of Cu/carbon steel gradient material, while it is still better than carbon steel, and it shows a clear passivation trend during corrosion. Therefore, the copper/carbon steel gradient material can significantly improve the corrosion resistance of carbon steel. Even after the surface copper layer is destroyed, the gradient material can protect the matrix and improve the service life of the material.

Effect of Cu on the Corrosion Resistance of the Carbon Steel

Effect of Cu, Mn on the Corrosion Performance of Carbon Steels in Wet/Dry Environments

Effects of Cu on Corrosion Resistance of Low Alloyed Steels in Acid Chloride Media

Effect of Cu on Corrosion Resistance Performance of Bridge Weathering Steels

Research on the Chloride Ion Corrosion Resistance of Cu-Sb-Added Low-Carbon Steel

Effects of Cu on the corrosion resistance of heat-treated weathering steel in a marine environment

Effects of Alloyed Cr and Cu on the Corrosion Behavior of Low-Alloy Steel in a Simulated Groundwater Solution

INFLUENCE OF Cu AND Mn ON CORROSION BEHAVIOR OF LOW ALLOY STEEL IN A SIMULATED COASTAL ENVIRONMENT

Corrosion Behaviour of Cu/Carbon Steel Gradient Material

Effects of Cr, Ni and Cu on the Corrosion Behavior of Low Carbon Microalloying Steel in a Cl− Containing Environment

Synergistic effect of Cu and Ni on atmospheric corrosion resistance for low-alloying steel in wet/dry cyclic industrial environment

The Effect of Cu Addition on the Electrochemical Corrosion and Passivation Behavior of Stainless Steels

Effects of Ti and Cu Addition on Inclusion Modification and Corrosion Behavior in Simulated Coarse-Grained Heat-Affected Zone of Low-Alloy Steels

Effects of Cu Content on the Corrosion Resistance and Antibacterial Property of Low Carbon Steels

Corrosion Behavior of Copper Bearing Steels and the Derived In-Situ Coating

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Cu on the Mechanical and Corrosion Resistance of Ferritic Stainless Steel Containing Sn

Influence of Carbon Content on Corrosion Resistance Performance of Weathering Steel

The Effect of Cu Addition on Corrosion Resistance of Al-Si-Mg-Cr Alloy

Corrosion Behavior of New Weathering Steel in the Environment Simulating Coastal Industrial Atmosphere

Effect of Alloying Element of Cu on Phase Proportion, Mechanical Properties and Corrosion Properties of Fe-Cr-Mn-Al Duplex Stainless Steel