Abstract:Starting with a bulk metallic glass-forming alloy Mg 65 Cu 18 Ni 6 Y 11 , we prepared in situ composites by increasing the Mg content in a series of alloys, Mg x (Cu 0.51 Ni 0.17 Y 0.32 ) 100− x (65 ≤ x ≤ 90), via copper mold casting of rods 4 mm in diameter. The fully glassy alloy at x = 65 showed a compressive fracture strength of 755 MPa but no observable macroscopic plasticity prior to failure. Metallic glass-based composites were formed when the Mg content was increased. For x > 80, the glassy phase no longer existed in the as-cast rods. In the composition range of 80 ≤ x ≤ 85, needle-shaped Mg solution with a 14H-type long period stacking (LPS) structure appeared as the primary phase in the as-cast microstructure. On further increase of the Mg content up to x = 90, the solidified primary phase became 2H-Mg, coexisting with the remaining eutectic structure. The best combination of mechanical properties was obtained for the alloy at x = 81.5, which showed a fracture strength of 665 MPa and a compressive plastic strain of 11.6%. The specific strength of this alloy was 2.8 × 10 5 N m kg −1 , much higher than conventional cast magnesium alloys. The mechanical properties are discussed in light of the phase selection and microstructural features uncovered in microscopy examinations.

Chill-cast in Situ Composites in the Pseudo-Ternary Mg–(Cu,Ni)–Y Glass-Forming System: Microstructure and Compressive Properties

Mg-based Bulk Metallic Glass Composites with Plasticity and High Strength

Mg-Al-Ca In-Situ Composites with a Refined Eutectic Structure and Their Compressive Properties

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Mg-based Bulk Metallic Glass Composites with Plasticity and Gigapascal Strength

Formation, Microstructure, and Mechanical Properties of in Situ Mg-Ni-(Gd,Nd) Bulk Metallic Glass Composite

Thermal Stability, Glass-Forming Ability and Mechanical Properties of Mg-Y-Zn-Cu Glassy Alloys

Formation of high strength Mg–Cu–Zn–Y alloys

Microstructure evolution and mechanical properties of Cu46Zr47Al7 bulk metallic glass composite containing CuZr crystallizing phases

The Effect of Primary Crystallizing Phases on Mechanical Properties of Cu46zr47al7 Bulk Metallic Glass Composites

Synthesis of La-based In-Situ Bulk Metallic Glass Matrix Composite

A new Mg65Cu7.5Ni7.5Zn5Ag 5Y10 bulk metallic glass with strong glass-forming ability

A New Mg 65 Cu 7.5 Ni 7.5 Zn 5 Ag 5 Y 10 Bulk Metallic Glass with Strong Glass-Forming Ability

Microstructural heterogeneities governing the deformation of Cu47.5Zr47.5Al5 bulk metallic glass composites

Structural and mechanical characterizations of ductile Fe particles-reinforced Mg-based bulk metallic glass composites

Cu-based bulk glassy alloys with high tensile strength of over 2000 MPa

Doubling the Critical Size for Bulk Metallic Glass Formation in the Mg−Cu−Y Ternary System

Preparation of Carbon-nanotube Reinforced Mg Based Bulk Metallic Glass Composites and Its Mechanical Properties

Mg–Cu–(Y,Nd) Pseudo-Ternary Bulk Metallic Glasses: the Effects of Nd on Glass-Forming Ability and Plasticity

The Research of Microstructure and Mechanical Properties of Mg–7Gd–3Y–1Nd–0.5Zn–0.5Zr (wt%) Alloy

Easy Glass Formation in Magnesium-Based Mg-Ni-Nd Alloys