Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Study on Degradation and Crosslinking of Impact Polypropylene Copolymer by Dynamic Rheological Measurement

THE DYNAMIC RHEOLOGICAL CHARACTERIZATION OF STRUCTURE DEVELOPMENT FOR IMPACT POLYPROPYLENE COPOLYMER MELT

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

The Effects of Irradiation Cross-Linking on the Thermal Degradation and Flame-Retardant Properties of the Hdpe/Eva/Magnesium Hydroxide Composites

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Microstructure, morphology, crystallization and rheological behavior of impact polypropylene copolymer

Probing Into the Annealing Effects on Microstructure and Mechanical Properties of Impact Polypropylene Copolymer With Nodular Crystalline Morphology

Influence of Shearing on Impact Polypropylene Copolymer: Phase Morphology, Thermal and Rheological Behavior

Effect of microstructure tuning by rapid heat cycle molding on the photodegradation behavior of isotactic polypropylene

Mechanical properties and structural characteristics of dynamically photocrosslinked PP/EPDM blends

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Correlation Between Oxidation-induced Crosslinking and Rheological Behavior of HDPE

Probing into the microstructural evolution of isotactic polypropylene during photo-oxidation degradation

Crystallization kinetics and morphology of high impact polypropylene

Correlation Between Impact Properties and Phase Structure in Impact Polypropylene Copolymer

Study on thermal behavior of impact polypropylene copolymer and its fractions

Reconstruction of Core-Shell Dispersed Particles in Impact Polypropylene Copolymer During Extrusion

Phase Morphology and Impact Toughness of Impact Polypropylene Copolymer

Morphology, Microstructure and Compatibility of Impact Polypropylene Copolymer

Destruction Mechanism of Core–shell Particles in Impact Polypropylene Copolymer During Short Molten-State Annealing

Investigation on thermo-stabilization effect and nonisothermal degradation kinetics of the new compound additives on polyoxymethylene