Abstract:Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.

Effect of Compression Properties on Germination and Growth for Flowering Chinese Cabbage Seeds

Research on Physicochemical Properties, Microscopic Characterization and Detection of Different Freezing-Damaged Corn Seeds

Nondestructive Evaluation of Chinese Cabbage Quality Using Mechanical Vibration Response

Effects on Relaxation Properties of Chinese Cabbage (brassica Campestris L.) Subjected to Different Compression Directions

Evaluation of Compactness As a Method to Quantitatively Assess Chinese Cabbage Texture

Effect of Shock Compression on Germination Rate of Plant Seeds

Factors Affecting Transformation Efficiency by Micro-Injecting Agrobacterium into Flower Bud of Chinese Cabbage

Compressive mechanical properties of cottonseed

Effect of the Crude Toxin from Seedborne Fusarium Oxysporum on Seed Germination and Seedlings of Cabbage

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

Optimization of cutting position and mode for cabbage harvesting

Effects of Wet and Dry Alternately Soaking and NaCl Treatments on Bottle Laqenaria siceraria Seed Germination

Effects of Water Extraction Ratio of Pig Manure and Its Compost on Seed Germinative Indicators

Effect of Air Disturbance on Seed-filling Performance of the Pneumatic Precision Seed-metering Device for Maize

Seed Biomechanical Monitoring: A New Method to Test Maize (zea Mays) Seed Vigour

Effects of Seeds Morphology on Pressure Distribution in the Cone Hole of Air-Blowing Seed-Metering Device Based on CFD

Establishment and Parameter Calibration of a Simulation Model of Coated Cotton Seeds and Soil

The Physical Parameters and Mechanical Properties of Small Round Seeds for Air Suction Precision Seed Metering Device

Preliminary study on Bioassay of Capparis spinosa L. seed extract and seed germination

Effect of Naphthalene Acetic Acid and Chitosan Coating on Germination Rate of Chinese Cabbage Seeds

Physical and Mechanical Experiments for Designing Cabbage Precision Trimming Device