Abstract:OBJECTIVETo establish a two-dimensional biological printing technique of hBMSCs so as to control the cell transfer process and keep cell viability after printing.METHODSBone marrow (5 mL) was obtained from healthy volunteer. The hBMSCs were regularly subcultured to harvest cells at passage 2, which were adjusted to the single cell suspension at a density of 1 x 10(6)/mL. The experiment was divided into 3 groups: printing group 1 in which cells underwent propidium iodide (PI) fluorescent labeling, then were transferred by rapid prototype biological printer (interval in x-axis 300 microm, interval in y-axis 1500 microm), and laser scanning confocal microscope was applied to observe cell fluorescence; printing group 2 in which cells received no PI labeling and were cultured for 2 hours after transfer, Live/Dead viability Kit was adopted to detect cell viability and laser scanning confocal microscope was applied to observe cell fluorescence; half of the cells in printing group receiving no Live/Dead viability Kit detection were cultured for 7 days, then inverted microscope was used to observe cell morphology, routine culture was conducted after the adherence of cells, the growth condition of cells was observed dynamically; control group in which steps were the same as the printing group 2 except that cell suspension received no printing.RESULTSLaser scanning confocal microscope observation on the cells in printing group 1 revealed the "cell ink droplets" were distributed regularly and evenly in the two-dimensional layer and each contained 15-35 cells, meeting the requirement of designing two-dimensional cell printing. The cells in printing group 2 went through cell viability test, laser scanning confocal microscope observation showed the fluorescence of cells 30 minutes after cell incubation. There was no significant difference between the control group and the printing groups in terms of cell viability. The printed cells presented normal adherence, good morphology and good growth state 7 days after routine culture.CONCLUSIONBiological printing technique can realize the oriented, quantificational and regular distribution of hBMSCs in the two-dimensional plane and lays the foundation for the construction of three-dimensional cell printing or even organ printing system.

[A Pilot Study of Three Dimensional Printing of Human Bone Marrow Stem Cells (Hbmscs)].

Projection-based 3D Bioprinting for Hydrogel Scaffold Manufacturing

[Preliminary Study on Biological Printing of Hbmscs].

Osteogenesis of Human Adipose-Derived Mesenchymal Stem Cells-Biomaterial Mixture in Vivo after 3 D Bio-Printing

Three-dimensional bio-printed constructs consisting of human umbilical-derived mesenchymal stem cells promote cell viability, proliferation, and differentiation in vitro.

Osteogenic Differentiation of Three-Dimensional Bioprinted Constructs Consisting of Human Adipose-Derived Stem Cells in Vitro and in Vivo

Modeling the Printability of Photocuring and Strength Adjustable Hydrogel Bioink During Projection-Based 3D Bioprinting.

Directly Coaxial 3D Bioprinting of Large-Scale Vascularized Tissue Constructs.

Construction of 3D bioprinting of HAP/collagen scaffold in gelation bath for bone tissue engineering

Bioprinting of Human Cord Blood-Derived CD34+ Cells and Exploration of the Multilineage Differentiation Ability in Vitro.

Preliminary Study on Three Dimensional Bioprinting of Human Dental Pulp Cells

3D bioprinting optimization of human mesenchymal stromal cell laden gelatin-alginate-collagen bioink

Three-dimensional bioprinting using a coaxial needle with viscous inks in bone tissue engineering - An In vitro study

3D Printing of Differentiated Bone Marrow Mesenchymal Cells As a New Method for Liver Tissue Engineering

[Three Dimensional Bioprinting Technology of Human Dental Pulp Cells Mixtures].

Extrusion bioprinting of cellular aggregates improves mesenchymal stem cell proliferation and differentiation

Complex Heterogeneous Tissue Constructs Containing Multiple Cell Types Prepared by Inkjet Printing Technology.

Three-dimensional bioprinting of embryonic stem cells directs highly uniform embryoid body formation.

Three-dimensional Bioprinting of Embryonic Stem Cells Directs Highly Uniform Embryoid Body Formation

Low temperature hybrid 3D printing of hierarchically porous bone tissue engineering scaffolds with in situ delivery of osteogenic peptide and mesenchymal stem cells

Culture of Human Bone Marrow Mesenchymal Stem Cells by Three-Dimensional Scaffold in Vitro: an Experimental Study