Abstract:The investigation of fabricating ultra‐compact solid‐state dye laser (SSDL) using N'N‐dimethylformamide (DMF) modified poly(methyl methacrylate) (PMMA) as the polymeric matrix was carried out. Atom transfer radical polymerization (ATRP) was introduced to manipulate the polymerization process of PMMA. By adjusting the additive amount of the FeIII complex (mixture of FeCl3 and 2,2’‐Bipyridyl (bPy)), the polymerization degree of PMMA was coordinated to gain better amplified spontaneous emission (ASE) properties of the embedded laser dye, Lumogen Orange 240 (LO). The ASE threshold of the FeIII complex catalyzed sample decreased as high as ~75%, from 225.3 ± 11.2 μJ cm−2 to 57.2 ± 2.9 μJ cm−2, comparing to that measured in common PMMA matrix. Additionally, a secondary dye, Stilbene 420 was added in the system for sharing excess excitation energy and oxidization damage, to overcome the photostability problem caused by the oxygen‐rich solvent, DMF. The operational lifetime of the resulted sample increased 200%, to the similar level of that without DMF component. Finally, by mechanical polishing and coating a thin film of silver at one end of the PMMA rod, an analogous Fabry‐Perot resonator was structured within the rod. Decent laser emission was obtained from the resulted SSDL without complex external cavities.

Solid State Dye Lasers Based on LDS 698 Doped in Modified Polymethyl Methacrylate

Solid state dye laser based on copolymer of methyl methacrylate with 2-hydroxyethyl methacrylate

Solid-state Dye Lasers Based on Polymethyl Methacrylate Modified with Methanol

Highly Efficient and Photostable Solid-State Dye Lasers Based on Modified Copolymers Doped with Pm567

Pm567-Doped Solid Dye Lasers Based on Pmma

Highly photostable solid-state dye lasers based on MPMMA co-doped with PM567 and C460

Solid Dye Lasers Based on 2-Hydroxypropyl Methacrylate and Methyl Methacrylate Copolymers

Investigation of Broadband Solid State Dye Laser Based on PM580 Doped PM MA

Solid-state lasers based on copolymers of methyl methacrylate and 2-hydroxyethyl acrylate doped with pyrromethene 567 dye

Enhanced Laser Characteristics of Pyrromethene 650 Using Modified PMMA As Solid Hosts

Tunable Solid-State Laser Based on Modified Polymethyl Methacrylate with Methanol Doped with Pyrromethene 580.

Highly Photostable Solid-State Dye Lasers Based on Mixed Pyrromethene 567 and Coumarin 500

Solid-state laser based on PMMA doped with Coumarin 540A

Solid State Dye Lasers Based on Coumarin 440 and Pyrromethene 567 Codoped Polymethyl Methacrylate

Properties of Improved Polymer Host Solid-State Dye Laser

Tunable Ultraviolet Solid-State Dye Laser Based on MPMMA Doped with Pyrromethene 597

Laser Properties and Photostabilities of Laser Dyes Doped in Ormosils

Tunable Solid-State Lasers Based on PMMA Doped with Pyrromethene Dyes

Tunable Solid-State Laser Based on MPMMA Co-Doped with Pyrromethene 567 and Rhodamine 610

Research of Solid-state Laser Based on Pre-polymerization PMMA Polymer Doped with Laser Dye

Polymeric Laser Rods Based on Modified Poly(methyl Methacrylate) Matrix Synthesized by FeIII Complex Catalyzed Atom Transfer Radical Polymerization with Enhanced Optical Gain and Photostability