Abstract:A shaping test of CuSn10 powders was carried out by using the selective laser melting (SLM) technology to study influences of process parameters of SLM on compactness of specimens. Meanwhile, process parameters were optimized based on the response surface methodology. Meanwhile, phase composition and microstructure of formed part were analyzed by XRD and OM. Results demonstrated that as the energy density of laser body increases from 146.7 J·mm -3 to 181.3 J·mm -3 , pores of samples decrease and the compactness increases from 98.97% to about 99.7%. Subsequently, the compactness begins to decrease with the continuous increase of laser energy density. The incomplete melting of powder under low energy density and gasification of powders under high energy density are major factors that influence the compactness. Over low or high laser energy density is disadvantageous for the improvement of compactness. A mathematical model of interaction between three factors (laser power, laser scanning speed and scanning space) and response value (compactness) was built up by using the BBD principle design test of response surface methodology. The degree of fitting (R 2 ) and correction coefficient (R 2 adj ) of the model were 0.9952 and 0.9866, which agree well with the fitting degree of experimental tests. Among three factors, influences of laser power and scanning speed on compactness are equivalent and more significant than scanning space. The optimal process parameters which were predicted by the model were laser power=331.471 W, scanning speed=648.045 mm·s -1 , scanning space=69.9302 μm. Under this circumstance, the compactness of CuSn10 powders after SLM is 99.75%. According to experimental verification, the practical value of compactness is 99.74%, showing a very small relative error. This proves that the BBD model is reliable. The shaped part is mainly composed of α-Cu phase and metastable phase β'-Cu13.7Sn. Compared with the original powders, the content of metastable phase β' increases significantly, while the δ-Cu41Sn11 phase disappears.

Experimental Research on Influence of Compactness in SLS of PA6 Powder Material

Experimental investigating and numerical simulations of the thermal behavior and process optimization for selective laser sintering of PA6

Process Parameter Optimization on Selective Laser Melting of CuSn10 Powders Based on Response Surface Methodology

Simulation and Experimental Analysis of the Laser Sintering of Nylon Powder

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

Experimental Study on Technological Parameters and Proportion of Selected Laser Sintered PS/PE Mixed Powders

Research on numerical simulation and experimental for temperature fields of thin layer powder with selective laser sintering

Advances in Thermal Modeling of Selective Laser Sintering of Metal Powders

Improvement on Selective Laser Sintering and Post-Processing of Polystyrene

Experimental and Numerical Investigation of Densification Behaviors During Powder Compaction

Effects of Particle Size on Mechanical Properties and Forming Accuracy of Prosopis chilensis Powder/Polyethersulfone Composites Produced via Selective Laser Sintering

Effects of laser sintering processing time and temperature on changes in polyamide 12 powder particle size, shape and distribution

Effects of Compaction Method and Sintering Process on Microstructure and Properties of Ti6Al4V Alloy Prepared by Sintering of Hydrogenerated Powder

Numerical study on the warm compaction and solid-state sintering of TiC/316L composite powders from particulate scale

Properties And Microstructure Of Pure Al Powder Compacts Using Spark Plasma Sintering

Melting process and mechanics on laser sintering of single layer polyamide 6 powder

Multi-scale phase-field modeling of layer-by-layer powder compact densification during solid-state direct metal laser sintering

Comparisons of Indirect Selective Laser Sintering with Selective Laser Melting

Selective Laser Sintering Parameter Optimization of Prosopis Chilensis/Polyethersulfone Composite Fabricated by AFS-360 SLS

Effect of Interface Behavior between Particles on Properties of Pure Al Powder Compacts by Spark Plasma Sintering.