Abstract:The C=C double bonds in the main chain of hydroxyl-terminated polybutadiene (DHTPB), obtained by the degradation of polybutadiene rubber, were partially epoxided using m-chloroperoxybenzoic acid (mCPBA) as epoxidation reagent. A series of epoxided HTPBs (EHTPB) with different epoxy contents (5%, 10% and 15%) were prepared by tuning the molar ratio of mCPBA to C=C double bonds. The structures of EHTPBs were characterized by Fourier transform-infrared (FTIR), nuclear magnetic resonance (H-1-NMR) spectroscopy and gel permeation chromatography (GPC). The epoxy percent in EHTPBs from H-1-NMR spectra was in accordance with the design. In addition, a series of EHTPB-based polyurethane elastomers (EPU) were prepared by the reaction between EHTPB and 4,4'-diphenylmethane diisocyanate with 1,4-butanediol as a chain extender. Mechanical and thermal properties of the EPU samples were characterized by tensile test, differential scanning calorimetry (DSC) and thermal gravity analysis (TGA). With increased epoxy percent in EHTPB, the Young's modulus and the tensile strength of the EPU samples increased, whereas the elongation at break decreased. The sample EPU10 prepared with 10% of epoxy had the best mechanical properties with 8.82 MPa as Young's modulus, 7.83 MPa as tensile strength, and (485 +/- 23)% as elongation at break. The elasticity recovery of the EPU sample was slightly better than HTPB-based PU (EPU0). The results with TGA test showed that the thermal degradation of EPU, similar to EPU0, was divided into three stages. However, the EPU samples had better thermal stability with the initial degradation temperature at 210 degrees C, about 30 degrees C higher than that of EPU0. The DSC results showed that the glass transition temperature (T-g) of EPU gradually increased as epoxy percent was increased, though still lower than that of HTPB (FHTPB) based PUs prepared by free-radical polymerization.

Preparation and Structure Analysis of Polyphenolhydroxy EPDM

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Synthesis of Polyethylene-G-polydimethylsiloxane Graft Copolymers by Copolymerization of Ethylene with Polydimethylsiloxane Macromonomer

Structure and Preperties of Reaction Rubber Blends of FPM/Modified EPDM

Characterization of chemical structure and morphology of MCS graft terpolymer

Synthesis and Characterization of Poly (hydroxyether Ketone) and Its Copolymers

Studies on the influence of soft-segment structure on the properties of polyurethane adhesive

Preparation of the EPDM/PBMA Organic Dispersion Based on In-Situ Polymerization: Application in the Protection of Flexible Electronic Devices

Synthesis and Reactivity of Hydroxypoly(ethylene Oxide) Propyl–b–polydimethylsiloxane–b–propyl Hydroxypoly(ethylene Oxide)

Structure and mechanical properties of SRP/HDPE/POE (EPR or EPDM) composites

Synthesis of EPDM-g-PMMA through atom transfer radical polymerization

Preparation and properties of C_5 petroleum resin/ethylene-propylene-diene monomer composites

Synthesis of 4-arms hydroxy-functionalized PMMA-b-PE through combining free radical polymerization with coordination polymerization

Synthesis and Characterization of Polystyrene-G-polydimethylsiloxane Copolymers

Study on Foaming Kinetics and Preparation of Epdm Foams

Study on Solution Polymerization of EPDM-g-MS by Grafting Method

Synthesis, Characterization, and Ring Opening Polymerization of Poly(1,4-Cyclohexylenedimethylene Terephthalate) Cyclic Oligomers

Preparation and properties of EPDM/TiO2 composites

Synthesis and Characterization of the Hydrophobic Diblock Copolymers of Poly(dimethylsiloxane)‐block‐poly(ethyl Methyl Acrylate) Through Atom Transfer Radical Polymerization

Poly(hydroxyether of bisphenol A)-block-polydimethylsiloxane alternating block copolymer and its nanostructured blends with epoxy resin