Abstract:In the present work, (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 were produced by common casting and hot-forging technology utilizing the SHS reactions between titanium and B4C, C powder. The microstructures of composites were examined using optical microscopy (OM) and transmission electron microscopy (TEM). The X-ray diffraction (XRD) was used to identify the phases that were present in the composites. There are three phases — TiB, TiC and titanium matrix alloy. TiB grows in short-fiber shape, whereas TiC grows in dendritic, equiaxed or near-equiaxed shape. TiB whiskers were made to align the longitudinal direction and TiC dendritic was broken up after hot-forging. The reinforcements are distributed uniformly in matrix alloy. The interfaces between reinforcements and titanium matrix alloy are very clean. The tensile strength (yield strength and ultimate tensile strength) and the Young's modulus improve with the addition of TiB whiskers and TiC particles although some reduction in ductility is observed. (TiBw+TiCp)/Ti6242 composites with TiB:TiC=4:1 will fracture on a lower level of applied stain due to deformation restraint of TiB whiskers on titanium matrix alloy. The (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 show higher tensile strength and ductility. The addition of graphite not only improves the tensile strength and the Young's modulus but also increases the ductility. The improved Young's moduli and increased tensile strengths of the composites are explained using shear lag and rule-of mixtures theories. The Young's moduli of the composites were found in good agreement with that calculated from Tsai–Halpin equation applied for discontinuous-reinforced composites.

Young’s Modulus of in Situ TiB Whiskers in Ti Metal Matrix Composites

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

IN SITU TiBW/Ti COMPOSITES WITH A NOVEL QUASI- CONTINUOUS NETWORK REINFORCEMENT ARCHITECTURE

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Microstructural Characterization of in Situ TiB Whiskers in Ti MMCs Fabricated by SPS

Growth Mechanism of in Situ Tib Whiskers in Spark Plasma Sintered Tib/Ti Metal Matrix Composites

In Situ Tib Reinforced Titanium Metal Matrix Composites Prepared by Spark Plasma Sintering

Microstructure and Tensile Properties of in Situ (tib+tic)/ti6242 (tib:Tic=1:1) Composites Prepared by Common Casting Technique

Formation evolution and strengthening of quasi-continuous network like TiB whiskers in the in-situ TiBw/TC21 matrix composites

Microstructure and Mechanical Behaviors of Titanium Matrix Composites Containing In Situ Whiskers Synthesized via Plasma Activated Sintering

Effect of TiB Whiskers Orientation on Mechanical Properties in an <I>In Situ</I> TiB/Ti-1100 Composite

Room temperature tensile fracture characteristics of in situ TiBw/Ti6Al4V composites with a quasi-continuous network architecture

The Mechanical Behavior Dependence on the TiB Whisker Realignment During Hot-Working in Titanium Matrix Composites

Microstructure and tensile properties of in situ synthesized (TiBw + TiCp)/Ti6242 composites

Tensile Properties of Ex-Situ Ti-TiC Metal Matrix Composites Manufactured by Laser Powder Bed Fusion

Effect of TiB Whiskers Orientation on Mechanical Properties in an In Situ TiB/Ti-1100 Composite

Microstructural Characterisation Ofin Situtib/ti Matrix Composites Prepared by Mechanical Alloying and Hot Pressing

Fabrication and Tensile Properties of in Situ TiBw and TiCp Hybrid-Reinforced Titanium Matrix Composites Based on Ti–B4C–C

An innovative TiB whisker architecture of titanium matrix composite devised by scanning electron beam remodeling

In Situ Preparation Of Titanium Matrix Composites Reinforced With Tib Whiskers Andy(2)O(3) Particles

Precipitation and Distribution Behavior of in Situ-Formed TiB Whiskers in Ti64 Composites Fabricated by Selective Laser Melting