Abstract:Recently, microchannel heat exchangers (MCHX) have been widely used in heat pump systems due to their high surface-to-volume ratio and high efficiency of heat transfer. However, when the MCHX operates in frosting conditions, its performance is adversely affected. To study the frost formation and distribution characteristics of MCHX, a comprehensive parametric study was performed for the MCHX with a larger fin pitch. The effects of fin geometries and environmental parameters on the frosting characteristics of MCHX were studied. Fin height ( F h ) can effectively inhibit frost formation, which is due to the increase of surface temperature with the increase of F h . When F h increased from 6.0 mm to 11.8 mm, the frost time increased by 30.5 %. However, the increase in F h also brings the penalty of reduced heat transfer rate. The effect of fin depth ( F d ) on frost formation performance is small because the frost is mainly deposited in the front part, resulting in the rear fin cannot work efficiently. Fin pitch ( F p ) is the most significant structural parameter affecting frosting performance. When F p increases from 1.6 mm to 4 mm, the frosting time increases by 4 times and frost mass increased by 2.2 times. This is because with the increase of F p , the frost blocking in the front part can be effectively delayed, and the distribution uniformity of the frost layer is improved. Lower surface temperature and higher humidity ratio significantly promote frost formation and reduce the uniformity of frost distribution. When the inlet temperature is reduced from -5 degrees C to -8 degrees C, the frosting time is shortened by 2.15 times, and the frost mass is reduced by 55.7 %. When the relative humidity increases from 76 % to 92 %, the frosting time is shortened by 2.15 times, and the frost mass is reduced by 42.5 %. The air velocity has a minor impact on the growth rate of frost in the front part. However, as the air velocity increases, the uniformity of frost distribution is significantly improved. When the air velocity increased from 1.1 m s - 1 to 2.2 m s - 1 , the mass of accumulated frost increased by 29.5 %. Furthermore, frost thickness and air-side heat transfer coefficient correlations were developed by testing 12 samples. The developed heat transfer coefficient correlation can accurately capture the changing trend of the j -factor. This study provides a fundamental understanding of the frosting characteristics of MCHX and can effectively guide the louvered fin optimization.

Research on Frosting Characteristic of Air Source Heat Pump under Different Structure Parameters of Airside Heat Exchanger

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

A Study on the Performance of the Airside Heat Exchanger under Frosting in an Air Source Heat Pump Water Heater/chiller Unit

Frosting for Airside Heat Exchanger of the Water Chiller/heater of Air Source Heat Pump

Experimental Study on Characteristics of an Air-Source Heat Pump Under Frosting/Defrosting Conditions

Effect of Fin Type on Frosting Characteristics of an Air-source Heat Pump

Modeling the Airside Dynamic Behavior of a Heat Exchanger under Frosting Conditions

Frosting Phenomenon and Frost-Free Technology of Outdoor Air Heat Exchanger for an Air-Source Heat Pump System in China: An Analysis and Review

Simulation and Analysis of Air Source Heat Pump Water Heater/Chiller under a Whole Year's Running Condition

Experimental study of the facing airflow on the performance of air-to-water heat pump unit under frosting conditions

Analysis on Performance of a Novel Frost-Free Air-Source Heat Pump System

Frosting in winter for air source heat pump heat/chiller unit

Study on the frosting performance of air cooled heat pump units

Frosting performances of the metal heat-transfer surface for the air-source heat pump in Harbin

Experimental Study on the Frosting and Heat Transfer Performance of Three Rows of Variable Pitch Finned Coils

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Frosting Characteristics of Microchannel Heat Exchangers: Parametric Studies and Correlation Development

Simulation study on evaporator frosting process of air source heat pump

Investigation on the performance coupling characteristics between a compound anti-frosting method and air source heat pump system

Study on the Characteristics of Spray Defrosting of Air Source Heat Pump Solution in High Humidity Areas

A Modelling Study on the Frosting Characteristics of a Novel Dual-Fan Outdoor Coil in an Air Source Heat Pump Unit