Abstract:Numerous combustion strategies have been suggested for compression ignition engines in order to meet the stringent emission regulations with minimal sacrifice in the fuel economy. Premixed charge compression ignition combustion has the potential to reduce the nitrogen oxide emissions and the soot emissions while maintaining a high thermal efficiency and has become the research focus recently. Experiments and simulations were used to study the effects of the injection mode and the injection timing on the premixed charge compression ignition combustion and the emissions in a heavy-duty diesel engine at low and medium loads. The results reveal the following. At low loads, when the injection timing of a single injection is 35° crank angle before top dead centre because of the impinging position of the spray, the mixture is divided into two parts: the fuel above the chamber and the fuel in the piston bowl. This helps to utilize fully the in-cylinder air to form a homogeneous mixture. Also the nitrogen oxide emissions are the lowest. At medium loads, with a single injection, the injection mass is increased, the injection duration is prolonged and the mixing timing is reduced. As a result, the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions are increased dramatically; the best emissions are gained at an injection timing of 35° crank angle before top dead centre owing to the combined effect of the optimized mixing time and the optimized mixing space. At medium loads, with multiple injections, the injection mass is divided into four pulses, the mixing timings of which are all increased. The mixing space of the fuel–air mixture is also improved, and a more homogeneous mixture is obtained, which is beneficial to decreasing the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions in comparison with those for the single-injection case. When the injection timings of multiple injections are 80° crank angle before top dead centre, 65° crank angle before top dead centre, 50° crank angle before top dead centre and 35° crank angle before top dead centre, the best trade-off between the performance and the emissions can be achieved at medium loads.

Study on Diesel Combustion and Emission Based on Injection Timing

Study on injection characteristics of diesel and DME

Influence of Multi-Injection on Combustion and Emission of Diesel Engine

Experimental Study on the Influence of Injection Timing on Combustion and Emission of Biodiesel Engine Based on Mechanical Mechanics

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

The Influence of Fuel Injection Timing on Exhaust Emission From a Diesel Engine

Effect of post-injection timing and EGR ratio on diesel low temperature combustion and emission

Experimental and computational study on the effects of injection timing on thermodynamics, combustion and emission characteristics of a natural gas (NG)-diesel dual fuel engine at low speed and low load

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Effect of Injection Strategy on Emission Characteristics of Compression Ignition Engine Fueled with Blended Fuel

Effects of the Injection Parameters on the Premixed Charge Compression Ignition Combustion and the Emissions in A Heavy-Duty Diesel Engine

Effect and optimization of injection timing on the combustion and particle emission of a gasoline engine

Study on Effect of Pilot Injection on Diesel Low Temperature Combustion

Combustion Characteristics and Particulate Emission in A Natural-Gas Direct-Injection Engine: Effects of the Injection Timing and the Spark Timing

Effect of Post-Injection on Combustion and Exhaust Emissions in DI Diesel Engine

Effects of Injection Timing on Combustion and Emission Performance of Dual-Fuel Diesel Engine under Low to Medium Load Conditions

Influence of Fuel Injection Timing on Combustion and Emission in Direct Injection Natural Gas Engine

Effect of Egr and Injection Timing on Combustion and Emission Characteristics of Split Injection Strategy Di-Diesel Engine Fueled with Biodiesel

Influence of Post-Injection Strategy on the Exhaust Emission and Fuel Consumption in a HSDI Diesel Engine

Analysis Of The Influence Of Pilot Injection Timing On Diesel Combustion In An Optical Engine By The Two-Color Method

Particulate Emission and Combustion Characteristics of a Direct-Injection Natural Gas Engine under Various Injection and Ignition Timings