Abstract:Introduction: Lunar heat flow provides important information for constraining internal temperature profile of the Moon, estimating the bulk concentration of radioactive elements (Th, U and K) in lunar crust, and testing models for formation and thermal evolution of the Moon [1]. Based on long-term measurements of Apollo heat flow probes, heat flows at the Apollo 15 and 17 landing sites were estimated as 0.021 and 0.016 Wm -2 , respectively [2]. Given these two measurements were conducted at the boundary between highlands and maria, it is still in debate whether the estimated heat flow is representative at global scale or not. Given the low dielectric loss of lunar regolith, microwave at proper frequency can penetrate several meters below lunar surface. Thermal emission from lunar surface layer correlates closely with subsurface temperature profile, from which internal heat flow of the Moon can be estimated. Therefore, spaceborne passive microwave remote sensing provide an effective tool for global studying of heat flow of the Moon. In this study, Chang’E-2 (CE-2) microwave radiometer (MRM) Level 2C data were analyzed with the purpose to invert lunar heat flow at global scale. The observed brightness temperatures (TBs) were preprocessed by radiation correction, removal of sidelobe components in Level 2A and 2B procedures, and validation based on ground truth at Apollo landing sites . Then a radiative transfer model is used to simulate thermal emission from lunar regolith layer, with considering the dielectric and temperature profile of lunar subsurface. This model shows a linear relation between brightness temperature and internal heat flow. Using this relation, heat flow at mid-latitude region (60°S – 60°N) is inverted from TB at 3 GHz. Thermal Emission Model and Heat Flow Inversion Approach: In this study, lunar surface layer is described by a two layer model, i.e., a regolith layer atop an underlying bedrock. The regolith layer is described by its physical temperature, dielectric constant and thickness, and the underlying bedrock is described by its dielectric constant. Using a similar radiative transfer approach as in [3], thermal emission from lunar surface layer can be calculated, with considering temperature and dielectric profiles within the regolith layer. Based on the relation among dielectric constant, bulk density and regolith composition [4], dielectric constant profile of regolith layer was introduced with an assumed porosity profile [5]. The model input physical temperature profile was obtained by resolving one-dimensional heat transfer equation [6] where temperature gradient at equilibrium depth is mostly dominated by internal heat flow [7]. Figure 1 shows the simulated TBs at 3.0, 7.8, 19.35 and 37 GHz as a function of heat flow for highland region at lunar midnight. It can be seen that TB at four channels increases linearly with internal heat flow. Among the four channels, 3.0 GHz is most sensitive to heat flow because of its larger penetration depth. Further analysis shows that this linear relation depends on frequency, FeO and TiO2 abundances, lunar regolith thickness, and local time. Therefore, as this parameter dependent relation (represented by two coefficients) is obtained from thermal emission model, lunar internal heat flow can be estimated from TB at 3 GHz.

Global Inventory of Helium-3 in Lunar Regoliths Estimated by a Multi-Channel Microwave Radiometer on the Chang-E 1 Lunar Satellite

Quantitative estimation of helium-3 spatial distribution in the lunar regolith layer

Moon-Based Ground Penetrating Radar Derivation of the Helium-3 Reservoir in the Regolith at the Chang'E-3 Landing Site

Investigating the Retention of Solar Wind Implanted Helium-3 on the Moon from the Analysis of Multi-Wavelength Remote Sensing Data

Analysis of Microwave Brightness Temperature of Lunar Surface and Inversion of Regolith Layer Thickness:Primary Results of Chang-E 1 Multi-Channel Radiometer Observation

Preliminary analysis of mircowave brightness temperature of the luanr surface from change 1 multi-channel radiometer observation and inversion of regolith layer thickness

Modeling, Simulation, Inversion and Chang E-1 Data Validation for Microwave Emission Remote Sensing of Lunar Surface Media

Inversion of Dielectric Properties of the Lunar Regolith Media With Temperature Profiles Using Chang'e Microwave Radiometer Observations

Regolith Properties in the Chang'E-5 Landing Region of the Moon: Results from Multi-Source Remote Sensing Observations

Bulk density of the lunar regolith at the Chang'E‐3 landing site as estimated from Lunar Penetrating Radar

Parameters and Structure of Lunar Regolith in Chang ' E-3 Landing Area from Lunar Penetrating Radar (lpr) Data

THORIUM ON THE LUNAR HIGHLANDS SURFACE : INSIGHTS FROM CHANG ’ E-2 GAMMA RAY SPECTROMETER

A preliminary estimation of lunar heat flow from chang ’ e-2 microwave radiometer observations

In Situ Photometric properties of Lunar Regolith Revealed by Lunar Mineralogical Spectrometer on board Chang'E‐5 Lander

Measurement and Uncertainty Analysis of Lunar Soil Water Content Via Heating Flux Method

Taking Advantage of Glass: Capturing and Retaining the Helium Gas on the Moon

Photometric Characteristics of Lunar Soils: Results from Spectral Analysis of Chang'E-5 In Situ Data Using Legendre Phase Function

A Novel Approach for Permittivity Estimation of Lunar Regolith Using the Lunar Penetrating Radar Onboard Chang’E-4 Rover

Properties of Lunar Regolith on the Moon's Farside Unveiled by Chang'E-4 Lunar Penetrating Radar

Lunar Regolith Stratigraphy Analysis Based on the Simulation of Lunar Penetrating Radar Signals

In situ detection of water on the Moon by the Chang'E-5 lander