Abstract:Carbon nanotubes (CNTs) have outstanding characteristics including high mechanical properties, namely tensile strength and elastic modulus,and still remarkable flexibility, excellent thermal and electric conductivities, low percolation thresholds (loading weight at which a sharp drop in resistivity occurs) and high aspect ratios (length to diameter ratio, L/D) while the latter provides the nanotubes with additional advantage over spherical fillers to obtain high property composites. Therefore I CNTs have the potential to act as a reinforcing filler of polymer matrices. The tetraglycidyl-4,4'-diaminodiphenylmethane (TGDDM) cured with 4,4'-diaminodiphenylsulphone WDS) and filled with graphite or carbon fibers are commonly used as a polymeric matrix in high performance composites employed in the aircraft and spacecraft industries. In present paper, multi-walled carbon nanotubes (MWNTs) as a nano-filler were incorporated in the TGDDM/DDS epoxy. The thermal properties of the composites were studied by differential scanning calorimetry (DSC), dynamic thermal analysis (DMTA) and thermal gravitimetric analysis TGA). In addition, the dispersion of MWNTs in the epoxy was also investigated by scanning electron microscopy SEM). In DSC studies, Kissinger and Flynn-Wall-Ozawa (FWO) methods were used to study the nonisothermal cure kinetics of the MWNTs filled TGDDM/DDS composites at different heating rates. The activation energy (E.) of cure reactions of the MWNTs filled epoxy composites was obtained by Kissinger and FWO methods. For all composites, the E. obtained by Kissinger method was slightly less than that of FWO method. With the addition of MWNTs, the E. of the epoxy composites decreased first and then increased with the increase of the MWNTs contents. These results showed that the incorporation of carbon nanotubes accelerated the cure reaction of the TGDDM/DDS epoxy at lower MWNTs content due to the interaction between the hydroxyl groups on the surface of nanotubes and the epoxy. However, due to the high surface energy of carbon nanotubes, the viscosity of MWNTs/epoxy composites increased at higher MWNTs content. Hence, the mobility of hydroxyl groups was hindered, and the reaction energy of composites increased with increasing MWNTs contents. The influence of carbon nanotubes on the thermal stability of the epoxy was studied by TGA. It is shown that MWNTs had little influence on the thermal stability of the cured epoxy. The storage modulus and glass transition temperature of MWNTs filled TGDDM/DDS were investigated by DMTA. It is seen that the storage modulus of TGDDM/DDS system was enhanced with the increasing of MWNTs content, that is, the modulus increased 6.3% and 7.8% at 1 wt % and 5 % MWNTs content, respectively. The glass transition temperature of the epoxy slightly decreased. Furthermore, the DMTA results of MWNTs/TGDDM/DDS composites were compared with that of carbon narrofibers (CNFs)/TGDDM/DDS composites. It was shown that the interactions between CNFs and epoxy were better those between that MWNTs and epoxy. The dispersion of carbon nanotubes in the epoxy was studied by SEM. The SEM results suggest that of MWNTs had poor dispersion in the cured epoxy. However, the radii of carbon nanotubes in the epoxy were greater than those of pure nanotubes. These results show the existence of interaction between carbon nanotubes and epoxy.

Progress in Preparation and Study of Property of Epoxy Resin/Carbon Nano-meter Tube Nano-meter Composite

Progress in the Study of Polymer/carbon Nanotube Nanocomposites

PREPARATION AND MECHANICAL PROPERTIES OF CARBON NANOTUBES/RESIN EPOXY COMPOSITE

Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

Preparation and Damping Properties of Cups-Stacked Carbon Nanotubes(Cscnts)/Prime 20

Progress of the study of carbon fiber/nanomaterial/epoxy hierarchical composites

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Study on Mechanical Properties of Carbon Nanotube Reinforced Carbon Fiber/ Epoxy Resin Composites

Preparation and functional study of epoxy composites reinforced with ultra-low content single-walled carbon nanotubes

Preparation and Application of High Strength Carbon Nanotubes/Polymer Composites

Research Development of Preparation and Characterization of Polypropylene/Carbon Nano-tube Composites

Interaction between carbon nanotubes with functional groups and epoxy resin and its effect on thermal properties of carbon nanotubes/epoxy composites

Microstructural design and mechanical performance of epoxy/carbon nanotube fiber composite

Thermo-Mechanical and Thermo-Electric Properties of a Carbon-Based Epoxy Resin: An Experimental, Statistical, and Numerical Investigation

Progress of Electrical Property in Polymer/Carbon Nanotube Composites

The mechanical and electrical properties of direct-spun carbon nanotube mat-epoxy composites

Thermoanalytical Studies of High Performance Epoxy/Carbon Nanotube Composites

Fabrication and properties of aligned multiwalled carbon nanotube-reinforced epoxy composites

Investigation on Tribological and Thermo-Mechanical Properties of Ti 3 C 2 Nanosheets/Epoxy Nanocomposites

Study of the Preparation and Properties of Carbon Nano-Tubes Doped TiO<sub>2</sub>/Glass Fiber Reinforced Plastics