Abstract:Developing formaldehyde-free and excellent water resistance has constantly been at the center of attention of wood adhesives. In addition to enhancing the adhesive itself, the modification of wood interface can also improve its bonding strength and water resistance. In this study, aqueous solutions of NaIO 4 and NaClO 2 have been sprayed onto the surface of poplar veneer evenly. An activated wood interface equipped with -CHO and -COOH was prepared. Traditional polyurethane adhesives are primarily two-component, with excessive manufacturing cost, complicated production and use procedures. In this study, a single component high branched polyurethane adhesive (GI) was synthesized via a A 2 +B 3 oligomerization method by using glycerol and isophorone diisocyanate (IPDI). Using branched polyamine (PA 4 N ) as a modifier, GI was modified to GI-PA 4 N , which was used as an adhesive and then hot pressed with the activated wood to make three-layer plywood. The bonding interface was equipped with urethane bonds, urea-based chemical bonds, amide bonds, Schiff bonds and hydrogen bond, which considerably enhanced the stability and water resistance of the bonding interface. FT-IR and XPS confirmed the existence of -CHO and -COOH at the interface of the activated wood, and characterized the synthesis mechanism and bonding mechanism of GI-PA 4 N . The results indicated that when the mass ratio of polyurethane to polyamine was 4:1, the overall performance of the adhesive was the best. The dry bonding strength increased from 1.92 MPa to 3.63 MPa, and the wet bonding strength increased from 1.77 MPa to 3.13 MPa, much higher than the minimum requirement of GB/T 17657–2013 (0.7 MPa). A formaldehyde-free, high-performance plywood with excellent water resistance was successfully prepared using wood interfacial activation and branched polyamine modification.

Study on Starch-Based Aqueous Polymer Isocyanate Adhesive for Plywood

Preparation and properties of isocyanate prepolymer/corn starch adhesive

Preparation of starch polyols adhesive

Preparation and characterization of the bonding performance of a starch-based water resistance adhesive by Schiff base reaction

Preparation, Characterization and Properties of Starch-Based Wood Adhesive

An Environmentally Friendly and High Wet-Bond Strength Adhesive Based on Starch, Itaconic Acid and Silicone

Easy Preparation, High Water Resistance Glucose-Based Environment-Friendly Wood Adhesives

Facile preparation of high-performance plywood adhesive from gelatinized corn starch crosslinked with ammonium dihydrogen phosphate

High-amylose starch-based gel as green adhesive for plywood: Adhesive property, water-resistance, and flame-retardancy

Characterization and properties of plywood bioadhesive derived from cottonseed protein and sawdust cellulose

Synthesis and Characterization of Sucrose and Ammonium Dihydrogen Phosphate (SADP) Adhesive for Plywood

Preparation of high-performance antibacterial/antifungal citric acid-starch adhesives based on physical entanglement and chemical crosslinking

Effectiveness of Surface Treatment on Bonding Performance of Starch-Based Aqueous Polymer Isocyanate Wood Adhesive

Preparation and characterization on the eco-friendly corn starch based adhesive of with salient water resistance, mildew resistance

Preparation of isocyanate virtual 'core-shell' and its application in wood adhesive

Synthesis and characterization of starch stabilized polyvinyl acetate-acrylic acid copolymer-based wood adhesive

Corn starch blended polyvinyl alcohol adhesive chemically modified by crosslinking and its applicability as polyvinyl acetate wood adhesive

Retrogress Mechanism of Starch-Based Aqueous Polymer Isocyanate Adhesive

Bonding properties of polyurethan enhanced by branched polyamine and wood interfacial activation

Construction of xylan-based wood adhesive via tailoring crosslinking and interfacial chemical covalent bonding

Environmentally friendly chitosan adhesives for plywood bonding