Abstract:A thin-film calorimeter has been developed to investigate the thermodynamic properties of thin films including battery layer sequences. A new approach, i.e., the application of high-temperature stable piezoelectric resonators as highly sensitive planar temperature sensor, is chosen. Thin films with a thickness of several micrometers of the material of interest are deposited on the resonators. The production or consumption of latent heat by the active layer(s) results in temperature fluctuations with respect to surroundings, in our case the furnace in which the sensor is placed. The temperature fluctuations can be easily monitored in situ via changes of the resonance frequency of the resonator. This enables us to extract the temperature and time dependence of phase transformations as well as the associated enthalpies. To cover a temperature range from −20 to 1000 °C, high-temperature stable piezoelectric langasite (La3Ga5SiO14) resonators are applied. Initially, aluminum and tin layers are used to test the calorimeter. The temperature and enthalpy of the solid–liquid phase transformation agree well with the literature data. Further, the thermodynamic data of the battery materials to be used as cathode, solid electrolyte, and anode in lithium ion batteries are investigated by the newly developed method. The cathode materials Li(Ni0.8Co0.15Al0.05)O2-δ (NCA) and LiMn2O4-δ (LMO) are amorphous after deposition and crystallize during heating. NCA shows this transformation at 455 °C with an enthalpy of −4.8 J/g. LMO undergoes three phase transformations at 330, 410 and 600 °C. They require initially an activation which is followed by an exothermic enthalpy. The associated energies (activation; enthalpy) are (+67.2; −50.2) J/g, (+29.3; −29.3) J/g, and (+20.4; −26.2) J/g, respectively. The solid electrolyte Li3.4V0.6Si0.4O4-δ (LVSO) shows no phase transformation up to its decomposition at about 220 °C. The anode material molybdenum disulfide (MoS2) exhibits a phase transformation at 480 °C with an enthalpy of −183.2 J/g.

Study on the Materials Thermal Properties of Lithium Ion Secondary Batteries by Using C 80 Calorimeter

Micro calorimeter study on the thermal stability of lithium-ion battery electrolytes

Comparison analysis on the thermal runaway of lithium-ion battery under two heating modes

Thermal Behavior Inside Lithium-ion Batteries

Thermal properties and kinetics study of charged LiCoO 2 by TG and C80 methods

Effects of electrolyte/cathode ratio on investigation of their thermal behaviors using differential scanning calorimetry

Experimental and Numerical Study of PCM Thermophysical Parameters on Lithium-Ion Battery Thermal Management

Thermal Stability of LiPF 6 /EC+DMC+EMC Electrolyte for Lithium Ion Batteries

Thermal Stability of LiPF6-based Electrolyte and Effect of Contact with Various Delithiated Cathodes of Li-ion Batteries

Application of Accelerating Rate Calorimeter in the Lithium-ion Battery Thermal Test

Methods for Quantitative Thermal Analysis of Lithium Solid-State and Beyond Battery Safety

Thermal Stabilities of LixCoO2 and its Coexisting with LiPF6/EC + DEC Electrolyte

High-temperature thin-film calorimetry: a newly developed method applied to lithium ion battery materials

Experimental Study of a Passive Thermal Management System Using Expanded Graphite/Polyethylene Glycol Composite for Lithium-Ion Batteries

Thermal behaviors of electrolytes in lithium-ion batteries determined by differential scanning calorimeter

Thermal stability of LiPF6/EC + DEC electrolyte with charged electrodes for lithium ion batteries

Thermal Stability and Reactivity of Cathode Materials for Li-Ion Batteries

Precise In-Situ and Ex-Situ Study on Thermal Behavior of LiNi1/3Co1/3Mn1/3O2/graphite Coin Cell: from Part to the Whole Cell

The Effect of Mass Ratio of Electrolyte and Electrodes on the Thermal Stabilities of Electrodes Used in Lithium Ion Battery

Effects of solvents and salt on the thermal stability of charged LiCoO2

Thermal Behavior of Lithiated Graphite with Electrolyte in Lithium-Ion Batteries