Abstract:Abstract With increasing aerodynamic and thermal loads, film cooling has been a popular technology integrated into the design of the modern gas turbine vane endwall, especially for the first-stage vane endwall. A staggering amount of research has been completed to quantify the effect of operating conditions and cooling hole geometrical properties. However, most of these investigations did not address the influence of the manufacturing tolerances, assembly errors, and operation degradations on the endwall misalignment. In this paper, uncertainty quantification (UQ) analysis was performed to quantify the impacts of upstream endwall misalignment uncertainties on the endwall film cooling performance and vane surface phantom cooling performance. The upstream endwall misalignment, step geometry with various step heights, commonly exists between the combustor exit and the first-stage vane endwall. Based on the non-intrusive polynomial chaos expansion (NIPC) and the uniform probability distribution assumption, the deviation (step height) uncertainties of the upstream endwall misalignment were quantified. To predict the endwall secondary flow and film cooling effectiveness in the transonic linear vane passage, the commercial computational fluid dynamic solver ANSYS FLUENT was used to numerically solve the three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) equations. The robustness analysis of endwall film cooling performance and phantom cooling performance to the upstream endwall misalignment was conducted for three design upstream step heights (ΔH): a baseline configuration (ΔH = 0 mm), two misaligned configurations with forward step (ΔH = −5 mm) and backward step (ΔH = 5 mm), respectively. Results show that the actual cooling performance has a high probability of deviating from the nominal value for the baseline configuration. The critical regions that are most sensitive to the upstream step misalignment are also identified by variances. The UQ results also show that the design geometry with a forward step has a more robust film cooling performance on endwall and phantom cooling performance on the vane pressure side surface, which means a smaller variance and a better expectation than the no-step configuration. In contrast, the design geometry with a backward step induces the reductions in the expectation of the film cooling effectiveness and coolant coverage and the amplification of performance fluctuations. This work provides a certain guiding direction for the optimization design for the upstream step geometry.

Performance Analysis of the Reheat-Stop-Valve Mechanism under Dimensional Tolerance, Misalignment and Thermal Impact

Research on New Type of Fast-Opening Mechanism in Steam Turbine Regulating System and Optimization of Operation Tactic

Thermo-mechanical Coupling Analysis of a High-Speed Actuating Mechanism Based on a New Thermal Contact Resistance Model

Investigation Into The Performance Of The Vl Seal Based On The 3d Model

Dynamic Behavior Analysis of a Rotor-Bearing-Squeeze Film Damper Coupling System with Bearing Outer Race Localized Defect

Thermo-mechanical Stress and Fatigue Damage Analysis on Multi-Stage High Pressure Reducing Valve

Parametric Analysis on Throttling Components of Multi-Stage High Pressure Reducing Valve

Hybrid Modelling of a High-Pressure Control Valve of a Steam Turbine at Off-Design Modes Using First-Principle Mechanism and Operational Data

Thermo-Mechanical Coupling Analysis of the Actuating Mechanism in a High Speed Press

Evaluation of the Viscous Heating Induced Jam Fault of Valve Spool by Fluid–structure Coupled Simulations

Numerical Simulation and Structure Improvement of Double Throttling in A High Parameter Pressure Reducing Valve

Angle-Regulating Rule of Guide Vanes of Variable Geometry Turbine Adjusting Mechanism

Numerical Analysis of Misaligned Guide Vanes Effect Pressure Oscillations in a Prototype Pump Turbine

Thermal Analysis and Simulation of Auxiliary Bearings and Its Application in the High Temperature Reactor-10

Fluid–Structure Coupling Analysis of the Stationary Structures of a Prototype Pump Turbine during Load Rejection

Numerical Analysis of the Effect of Misaligned Guide Vanes on Improving S-Shaped Characteristics for a Pump-Turbine

Thermal error prediction and reliability analysis of the main shaft bearing at wind turbines

Numerical and Experimental Investigation on Thermohydrodynamic Performance of Turbocharger Rotor-Bearing System

Reliability and Sensitivity Analyses of HPT Blade-Tip Radial Running Clearance Using Multiply Response Surface Model

Hybrid Modelling and Digital Twin Development of a Steam Turbine Control Stage for Online Performance Monitoring

Uncertainty Quantification on the Cooling Performance of a Transonic Turbine Vane With Upstream Endwall Misalignment